FORD FLTM BV 107-03-2000 WEATHERSTRIP SEALER - PLASTICIZER MIGRATION (Replaces FLTM BV 007-03 FLTM EU-BV 007-03)《挡风雨条密封剂 增塑剂迁移性 替代FLTM BV 007-03 FLTM EU-BV 007-03[替代 FORD FLTM BV 0.pdf

《FORD FLTM BV 107-03-2000 WEATHERSTRIP SEALER - PLASTICIZER MIGRATION (Replaces FLTM BV 007-03 FLTM EU-BV 007-03)《挡风雨条密封剂 增塑剂迁移性 替代FLTM BV 007-03 FLTM EU-BV 007-03[替代 FORD FLTM BV 0.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BV 107-03-2000 WEATHERSTRIP SEALER - PLASTICIZER MIGRATION (Replaces FLTM BV 007-03 FLTM EU-BV 007-03)《挡风雨条密封剂 增塑剂迁移性 替代FLTM BV 007-03 FLTM EU-BV 007-03[替代 FORD FLTM BV 0.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BV 107-03 Date Action Revisions 2000 12 11 Revised Editorial no technical change A. Cockman 1992 06 29 Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. WEATHERSTRIP SEALER - PLASTICIZER MIGRATION Application This method simulates

2、 production application of automotive windshield sealers to determine whether the sealer will stain headlining material by plasticizer migration. Apparatus Required Mechanical Convection Oven Capable of maintaining a constant temperature of 102 +/- 2 C. Pinch Weld Flange Refer to Figure 1. Materials

3、 Required Headlining Material 100 mm wide x 150 mm long; material as required by the applicable Engineering Material Specification. Paper Masking Tape Weatherstrip 100 mm long; material as required by the applicable Engineering Material Specification. Conditioning and Test Conditions All test values

4、 indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST METHOD BV 107-03 Page 2 of 3 Copyright 2000, For

5、d Global Technologies, Inc. Procedure 1. Fill the rubber channel of the weatherstrip which fits over the pinch weld flange with the sealer under test. Refer to Figure 1. 2. Drape the 100 mm section of the headlining material over the pinch weld flange as shown in Figure 1 and secure with the masking

6、 tape. The tape should contact just enough of the edge of the headlining to secure it to the metal flange. 3. Assemble the flange and the headlining to the rubber weatherstrip by fully inserting the flange into the channel of the weatherstrip containing the sealer. 4. Place the assembly into the ove

7、n at 102 +/- 2 C for 70 h. Allow the headlining to hang freely from the assembly. Evaluation 1. Remove the assembly from the oven and cool to 23 +/- 2 C. 2. Examine and report any staining of the headlining resulting from plasticizer migration. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BV 107-03 Page 3 of 3 Copyright 2000, Ford Global Technologies, Inc. WEATHERSTRIP SEALER - PLASTICIZER MIGRATION Figure 1