EN ISO 7143-2007 en Binders for paints and varnishes - Methods of test for characterizing water-based binders《色漆和清漆用基料 表征水性基料的试验方法》.pdf

《EN ISO 7143-2007 en Binders for paints and varnishes - Methods of test for characterizing water-based binders《色漆和清漆用基料 表征水性基料的试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 7143-2007 en Binders for paints and varnishes - Methods of test for characterizing water-based binders《色漆和清漆用基料 表征水性基料的试验方法》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN ISO 7143:2007Binders for paints and varnishes Methods of test for characterizing water-based bindersThe European Standard EN ISO 7143:2007 has the status of a British StandardICS 87.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g

2、50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN ISO 7143:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 580 50378 8National forewordThis

3、 British Standard was published by BSI. It is the UK implementation of EN ISO 7143:2007. It supersedes BS EN ISO 7143:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee STI/3, Paints, media and related products.A list of organizations represented on

4、 STI/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publi

5、cationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 7143February 2007ICS 87.060.20 Supersedes EN ISO 7143:2004 English VersionBinders for paints and varnishes - Methods of test forcharacterizing water-based binders (ISO 7143:2007)Liants pour peintures et vernis - Mthode

6、s dessai pourcaractriser les liants base deau (ISO 7143:2007)Bindemittel fr Beschichtungsstoffe - Prfverfahren zurCharakterisierung von wasserverdnnbaren Bindemitteln(ISO 7143:2007)This European Standard was approved by CEN on 6 February 2007.CEN members are bound to comply with the CEN/CENELEC Inte

7、rnal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN membe

8、r.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members ar

9、e the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerl

10、and and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO

11、7143:2007: EForeword This document (EN ISO 7143:2007) has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes“ in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes“, the secretariat of which is held by DIN. This European Standard shall be given the status of a

12、national standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. This document supersedes EN ISO 7143:2004. According to the CEN/CENELEC Internal Regulations, the nationa

13、l standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

14、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 7143:2007 has been approved by CEN as EN ISO 7143:2007 without any modifications. EN ISO 7143:2007Reference numberISO 7143:2007(E)INTERNATIONAL STANDARD ISO7143Third edition2

15、007-02-01Binders for paints and varnishes Methods of test for characterizing water-based binders Liants pour peintures et vernis Mthodes dessai pour caractriser les liants base deau EN ISO 7143:2007ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of n

16、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter

17、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the

18、 rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by

19、 at least 75 % of the member bodies casting a vote. ISO 7142 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10, Test methods for binders for paints and varnishes, in collaboration with CEN Technical Committee CEN/TC 139, Paints and varnishes. This third edition

20、cancels and replaces the second edition (ISO 7143:2000), which has been technically revised. The major changes are as follows: a) water-based coating materials have been excluded from the scope because these products are not specified in accordance with this standard; b) the determination of molecul

21、ar mass has been added to Table 1; c) the normative references have been updated and the text has been editorially revised. Readers should note that ISO 12000 gives definitions relative to polymer dispersions and lattices, and identifies the test methods applicable to the determination of their prop

22、erties. ISO 12000 covers both aqueous and non-aqueous polymer dispersions, and products of synthetic and natural origin, including synthetic rubber latices. It was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials, in close collaboration with ISO/TC 45,

23、Rubber and rubber products. EN ISO 7143:2007blank1Binders for paints and varnishes Methods of test for characterizing water-based binders 1 Scope This International Standard specifies methods of test for characterizing binders, i.e. aqueous dispersions and solutions of polymers and copolymers, in pa

24、rticular those used as raw materials for water-based coating materials. The properties determined will depend on whether a drying or curing system is tested. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t

25、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 976, Rubber and plastics Polymer dispersions and rubber latices Determination of pH ISO 2115, Plastics Polymer dispersions Determination of white point temperature

26、and minimum film-forming temperature ISO 2811-1, Paints and varnishes Determination of density Part 1: Pyknometer method ISO 3219, Plastics Polymers/resins in the liquid state or as emulsions or dispersions Determination of viscosity using a rotational viscometer with defined shear rate ISO 3251, Pa

27、ints, varnishes and plastics Determination of non-volatile-matter content ISO 4576, Plastics Polymer dispersions Determination of sieve residue (gross particle and coagulum content) ISO 11357-2, Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature IS

28、O 11359-2, Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature ISO 13741-1, Plastics/rubber Polymer dispersions and rubber latices (natural and synthetic) Determination of residual monomers and other organic compo

29、nents by capillary-column gas chromatography Part 1: Direct liquid injection method ISO 13741-2, Plastics/rubber Polymer dispersions and rubber latices (natural and synthetic) Determination of residual monomers and other organic components by capillary-column gas chromatography Part 2: Headspace met

30、hod ISO 13885-1, Binders for paints and varnishes Gel permeation chromatography (GPC) Part 1: Tetrahydrofuran (THF) as eluent ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling EN ISO 7143:20072 ISO 15880, Paints, varnishes and binders Determination of MEQ value of wate

31、r-based coating materials and binders ISO 16805, Binders for paints and varnishes Determination of glass transition temperature 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 polymer dispersion liquid or semi-liquid material, usually milkwhi

32、te, containing the polymeric material in a stable condition, finely dispersed in a continuous liquid phase, normally water (aqueous dispersion) or an organic liquid (non-aqueous dispersion, NAD) ISO 4618:2006 3.2 water-based binder binder in which the main component of the volatile matter is water 4

33、 Sampling Take a representative sample of the product to be tested, as described in ISO 15528. 5 Methods of test The test methods used for a particular binder shall be the subject of agreement between the interested parties, if not otherwise specified. The properties given in Table 1 are considered

34、as characterizing properties of water-based binders, in particular if they are used as raw materials for paints and varnishes. If reactive groups, e.g. hydroxyl groups, are to be determined, the test shall be carried out as for organic binders, before diluting with water. 6 Test report The test repo

35、rt shall contain at least the following information: a) a reference to this International Standard (ISO 7143:2007); b) all details necessary for complete identification of the product tested (manufacturer, trade name, batch number, etc.); c) the results of the tests and the test methods used; d) any

36、 deviations from the procedures specified; e) the dates of the tests. EN ISO 7143:20073Table 1 Characterizing properties and test methods Property Method of test Viscosity ISO 3219 Non-volatile matter ISO 3251 pH-value ISO 976 Sieve residue (gross particle and coagulum content) ISO 4576 Minimum film

37、-forming temperature ISO 2115 Glass transition temperature ISO 16805 Density ISO 2811-1 Residual monomers ISO 13741-1 and ISO 13741-2 Particle size distribution To be agreed between the interested parties aMEQ value ISO 15880 Molecular mass ISO 13885-1 baThe results of particle size analysis, for ex

38、ample with PCS (photon correlation spectroscopy), strongly depend on the details of the method. The results obtained by different laboratories can therefore be compared only if common reference samples are used. bThe results of GPC (gel permeation chromatography) analysis are relative values and dep

39、end on the separation factor, column material, detector, etc. The data obtained by different laboratories can therefore be compared only if common reference samples are used. EN ISO 7143:20074 Bibliography 1 ISO 4618:2006, Paints and varnishes Terms and definitions 2 ISO 12000, Plastics/rubber Polym

40、er dispersions and rubber latices (natural and synthetic) Definitions and review of test methods EN ISO 7143:2007blankBS EN ISO 7143:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents

41、 the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to im

42、prove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 900

43、0. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Service

44、s. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, u

45、nless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its p

46、roducts and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other be

47、nefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.

48、bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tran

49、smitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obt