FORD FLTM BU 154-03-2007 PRODUCTION FACILITY PAINTED TEST PANEL PREPARATION METHOD FOR QUICK KNIFE ADHESION TEST (FLTM BU 154-01)《快刀粘附力试验用涂漆板的制备方法（FLTM BU 154-01）》.pdf

《FORD FLTM BU 154-03-2007 PRODUCTION FACILITY PAINTED TEST PANEL PREPARATION METHOD FOR QUICK KNIFE ADHESION TEST (FLTM BU 154-01)《快刀粘附力试验用涂漆板的制备方法（FLTM BU 154-01）》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BU 154-03-2007 PRODUCTION FACILITY PAINTED TEST PANEL PREPARATION METHOD FOR QUICK KNIFE ADHESION TEST (FLTM BU 154-01)《快刀粘附力试验用涂漆板的制备方法（FLTM BU 154-01）》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHODBU 154-03Date Action Revisions 2007 01 23 Activated H. Kon, M. MehandruPrinted copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 1 of 2 PRODUCTION FACILITY PAINTED TEST PANEL PREPARATION METHOD FOR QUICK KNIFE ADHESION TEST (FLTM BU 154-01) APPLIC

2、ATION This procedure is used to prepare painted panels through the production paint facility process for Direct Glazing (Urethane adhesive to Painted Metal substrate) performance evaluation of Primerless and non-Primerless systems via Quick Knife Adhesion Test. REQUIRED EQUIPMENT/MATERIALS Electroco

3、ated steel 4 in. x 12 in. (101 mm x 304 mm) panels, with one long edge taped for film build measurement purposes (two strips of in. or 12 mm tape, leaving 3 in. x 12 in. or 75 mm x 304 mm of testable area) Production Paint facility and materials Supporting documents: o FLTM BU 154-01 o AVP-T118-001

4、TEST PROCEDURE Test Panel Preparation Procedure: 1. Fixture test panel to production unit prior to topcoat spray booths. Panel should be in windshield opening, adjacent to windshield flange and attached using spring clips or other appropriate method. See Figure 1 for panel placement options on typic

5、al vehicle. Note: Test panel location shall be based on plant facility capability of applying topcoat film builds representative of those on production flanges and once established, shall not be changed unless approved by Paint Engineering. 2. Allow test panel to travel through standard production p

6、aint process, i.e. topcoat spray booths and ovens, on the production unit. 3. Remove test panel from production unit after exiting last oven, taking care not to touch or contaminate the painted face of panels. 4. If evaluating tutone or repair adhesion performance, repeat steps 1 3 with the same pan

7、el on another production unit of the same color. Test Panel Labeling and Handling: 1. Painted Test panels must be labeled with the following information: a. Date of preparation b. Spray booth/oven identification c. Basecoat Color, M-code, and topcoat technology d. Any special processing, e.g. Repair

8、 panel, Fresh Setup, non-production adhesive etc. 2. If evaluating adhesion performance on fresh paint, i.e. “Fresh Setup,“ apply primer (if applicable) and direct glazing adhesive per supplier process standards within 4 hours of oven exit. 3. If test facility is off-site, wrap painted test panels i

9、ndividually, or two panels back-to-back, in clean aluminum foil, taking care not to touch or contaminate the painted face of panels. 4. Transport/ship panels to test facility for evaluation per FLTM BU154-01 FORD LABORATORY TEST METHODBU 154-03Printed copies are uncontrolled Copyright 2007, Ford Glo

10、bal Technologies, LLC Page 2 of 2 REPORT 1. Panel label information 2. Average topcoat film build, clearcoat film build preferred, on panel 3. Most recent topcoat oven curves to panel preparation timeframe 4. Layering separation distance per FLTM BU 154-01 5. Separation Mode per FLTM BU 154-01 KEY WORDS Glass Bonding Quick Knife Figure 1