FORD ESB-M4D233-C-2009 POLYVINYL CHLORIDE COPOLYMER FOAM - HIGH DENSITY TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚氯乙烯共聚物泡沫 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESB-M4D233-C-2009 POLYVINYL CHLORIDE COPOLYMER FOAM - HIGH DENSITY TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚氯乙烯共聚物泡沫 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M4D233-C-2009 POLYVINYL CHLORIDE COPOLYMER FOAM - HIGH DENSITY TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚氯乙烯共聚物泡沫 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 07 28 N-STATUS No Replacement Named Y. Bankowski, NA 2007 02 05 Revised Inserted 3.0; Deleted 3.1, 3.13, 4 1980 09 30 Released AL1-6000-66 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 1 of 3 POLYVINYL

2、 CHLORIDE COPOLYMER FOAM - HIGH DENSITY ESB-M4D233-C NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a high density vinyl chloride copolymer foam. 2. APPLICATION This specification was released originally for padding in landau top roof construction. It has low wa

3、ter absorption and low compression set properties. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 CELL STRUCTURE A consistant medium sized cell

4、structure, with no large voids or solid spots. 3.3 DENSITY 9 - 11 lb/ft3(144 - 176 kg/m3) 3.4 TENSILE STRENGTH, min 70 psi (482 kPa) (ASTM D 412, Die “A ) Elongation, min 140% 3.5 25% COMPRESSION - DEFLECTION, min 6 - 9 psi (41 - 62 kPa) (ASTM D 1056) 3.6 DIMENSIONAL STABILITY, max +/- 5% Test Metho

5、d: A 12 x 12 in (300 x 300 mm) sample, with reference marks 10 (250 mm) apart, (length and width) shall be subjected to a temperature of 121 +/- 3 C for 30 min in a mechanical convection oven. After cooling to 23 +/- 2 C, sample shall be measured for linear dimensional change in both directions. 3.7

6、 WATER ABSORPTION, max 6% (ASTM D 1056) 3.8 COMPRESSION SET, max 50% (ASTM 395, Method “B“, 23 +/- 2 C, 50% deflection for 22 h) ENGINEERING MATERIAL SPECIFICATIONESB-M4D233-CPrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 3 3.9 COLD FLEXIBILITY No cracking pe

7、rmitted (ASTM F 147, condition a 1 x 6 x 3/16 in (25 x 150 x 4.8 mm) sample in a cold box at -23 +/- 1 C for 4 h and bend 180 around a temperature conditioned 2 in (50 mm) mandrel) 3.10 COMPATIBILITY WITH VINYL TOP MATERIAL (Requirement for Initial Qualification Only) Shall be no evidence of blister

8、ing, foam collapse, or staining of the vinyl top material after the following environmental conditions. Ultraviolet Light Exposure 200 h (FLTM BU 105-01) Weatherometer Exposure 500 h (FLTM BO 101-01) Dry Heat Aging at 88 +/- 2 C 200 h (mechanical convention oven) Humidity Aging at 38 +/- 1 C 14 days

9、 (95 - 100% Relative Humidity) Florida Exposure 12 months (5 DWI, Miami, Florida) Sample Preparation: Spray apply ESB-M2G202 vinyl top adhesive at a dry coating weight of 3.0 - 3.5 oz/sq yd (0.10 - 0.12 kg/m2) to one side of a 4 x 12 x 3/16 in (100 x 300 x 4.8 mm) foam pad. Allow the adhesive 5 min

10、open time then position the foam pad, adhesive side down, on a 4 x 12 x 0.035 in (100 x 300 x 0.89 mm), ESB-M6J119 taupe primed steel panel. Within 5 s after positioning, roll the bonded area with a 4.5 lb (2.0 kg roller (ASTM D 1000) using one forward and one backward stroke along both the length a

11、nd across the width of the panel. Repeat Step 1 except apply adhesive to the fabric side of a 6 x 14 in (150 x 350 mm) white or light colored sample of ESB-M2F143 vinyl top material. Position the vinyl top material, adhesive side down, on the foam padded panel and wrap the excess fabric around panel

12、 back. Condition the assembled panels at 23 +/- 2 C for 72 h prior to environmental exposure. Save test panels after exposure for 180 Peel Adhesion Strength, para. 3.11 3.11 180 PEEL ADHESION STRENGTH, average min 32 oz/in (Requirement for Initial Qualification (0.35 N/mm) width Only - ASTM D 903, c

13、ondition each tested panels in para. 3.10 at 23 +/- 2 C for 72 h then determine adhesion of the vinyl top material to the foam padding and the foam padding to the primed panel) ENGINEERING MATERIAL SPECIFICATIONESB-M4D233-CPrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC

14、 Page 3 of 3 3.12 ODOR No objectionable or offensive odor 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 Material Background This material was developed to eliminate field problems associated with ESB-M4D233-A foam padding collapse, and to reduce permanent compression set caused by ski rack loading. In addition, this material eliminates the need for polyester sheeting which currently backs the ESB-M4D233-A foam padding to maintain its shape during installation.