FORD ESA-M2D52-A-2004 HOSE HIGH TEMPERATURE - LOW PRESSURE - OIL RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐高温、低压、抗油软管 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESA-M2D52-A-2004 HOSE HIGH TEMPERATURE - LOW PRESSURE - OIL RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐高温、低压、抗油软管 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESA-M2D52-A-2004 HOSE HIGH TEMPERATURE - LOW PRESSURE - OIL RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐高温、低压、抗油软管 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONHOSE, HIGH TEMPERATURE - LOW PRESSURE ESA-M2D52-A - OIL RESISTANT 1. SCOPE The material defined by this specification is a high temperature, oil resistant, low pressure hose. 2. APPLICATION This specification was released originally for material used as a transmiss

2、ion oil cooler hose. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 CONSTRUCTION Shall be constructed of a high temperature, oil resistant, synt

3、hetic rubber tube. The tube shall be covered with a single fabric braid reinforcement, or a single fabric braid covered with a heat and ozone resistant rubber outer cover. 3.2 ELONGATION AND CONTRACTION +2 to -4% (At 40 +/- 5 psi (276 +/- 34 kPa) working pressure) 3.3 BURSTING STRENGTH (ASTM D 380)

4、Must not burst below the minimum specified in Table I. 3.4 TENSILE STRENGTH (ASTM D 380, 1 in (25 mm)/min) This requirement applies only when couplings are used with the hose. Assemblies must withstand a minimum pull as specified in Table I without the couplings pulling off or rupture of the hose. 3

5、.5 ADHESION, min 8 lb/in (1.4 kN/m) Test Method: Measure the force of pull required to strip 1 in (25 mm) width of cover from the braid, as applied at right angle to the center line of the hose. 3.6 VOLUME CHANGE, Inner Tube, max +110% (ASTM D 380, immersion in ASTM No. 3 oil for 70 h at 149 C) Date

6、 Action Revisions 2004 09 09 Revised Inserted 3.0; Deleted 3.11 & 4 1979 12 17 Metricated, Renumbered and Retyped after Rev A CAJ2-822980-C6 Printed copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 1 of 3 ENGINEERING MATERIAL SPECIFICATIONESA-M2D52-A 3.7 COLD FLEXIBILITY No

7、 breaking or cracking 3.7.1 As Received Test Method: Condition hose assembly in a straight position at -40 +/- 1 C for 70 h. After conditioning and without removal from the cold box, bend the hose around a temperature conditioned mandrel, having a radius equal to the minimum bend radius as shown in

8、Table I. 3.7.2 Aged Hose assembly shall be oil aged at 149 C for 24 h. Oil aging medium shall be a Ford Motor Company approved automatic transmission fluid. The oil aged hose assembly, after cooling to 23 +/- 2 C, shall be conditioned in a cold box in straight position at -40 C for 4 h. After condit

9、ioning and without removal from cold box, the hose assembly shall be bent around a temperature conditioned mandrel, having a radius equal to the minimum bend radius as shown in Table I. 3.8 IMPULSE, min 100,000 cycles Test Method: Age the samples in a Ford Motor Company approved automatic transmissi

10、on fluid at 149 +/- 3 C for 70 h. The aged hose assemblies must withstand 100,000 cycles at the maximum working pressure listed in Table I without showing signs of deterioration. 3.9 OZONE RATING Must meet (FLTM BP 101-01) ESB-M9P1-A 3.10 DETERIORATION Hose assemblies shall be oil aged for 70 h at 1

11、49 C. Oil aging medium shall be a Ford Motor Company approved automatic transmission fluid. The oil aged hose assemblies shall be subjected to the burst and tensile tests. The results of the tests shall average not more than 15% below the average of the original results. (para. 3.3 and 3.4) Printed

12、copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 2 of 3 ENGINEERING MATERIAL SPECIFICATION ESA-M2D52-A TABLE 1 Recommended Working Hose I.D. Limits, Hose O.D. Limits, Burst Pressure, Pressure, psi (Mpa) Assembly Tensile Bend Radius, I.D., in in (mm) O.D., in in (mm) psi (Mp

13、a), min At 135 C At 149 C Strength, ib (kN), min in (mm), min 5/16 0.350 (8.89) 9/16 0.594 (15.09) 1600 (11.0) 325 (2.2) 160 (1.1) 200 (0.9) 3 (76) 0.310 (7.87) 0.531 (13.49 3/8/ 0.370 (9.40) 5/8 0.640 (16.26) 1500 (10.3) 300 (2.1) 150 (1.0) 250 (1.1) 3-1/2 (88) 0.330 (8.38) 0.594 (15.09) 1/2 0.531 (13.49) 25/32 0.812 (20.62) 1000 (6.9) 200 (1.4) 100 (0.7) 300 (1.3) 5 (127) 0.469 (11.91) 0.750 (19.05) Printed copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 3 of 3