ETSI TS 137 145-2-2018 Universal Mobile Telecommunications System (UMTS) LTE Active Antenna System (AAS) Base Station (BS) conformance testing Part 2 radiated conformance testing (.pdf

《ETSI TS 137 145-2-2018 Universal Mobile Telecommunications System (UMTS) LTE Active Antenna System (AAS) Base Station (BS) conformance testing Part 2 radiated conformance testing (.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 137 145-2-2018 Universal Mobile Telecommunications System (UMTS) LTE Active Antenna System (AAS) Base Station (BS) conformance testing Part 2 radiated conformance testing (.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 137 145-2 V14.3.0 (2018-01) Universal Mobile Telecommunications System (UMTS); LTE; Active Antenna System (AAS) Base Station (BS) conformance testing; Part 2: radiated conformance testing (3GPP TS 37.145-2 version 14.3.0 Release 14) TECHNICAL SPECIFICATION ETSI ETSI TS 137 145-2 V14.3.0 (20

2、18-01)13GPP TS 37.145-2 version 14.3.0 Release 14Reference RTS/TSGR-0437145-2ve30 Keywords LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous

3、-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall n

4、ot be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secr

5、etariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document,

6、 please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written

7、 permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI re

8、gistered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association.

9、ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)23GPP TS 37.145-2 version 14.3.0 Release 14Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly av

10、ailable for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web se

11、rver (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may bec

12、ome, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or re

13、produce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partners

14、hip Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI ident

15、ities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verba

16、l forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)33GPP TS 37.145-2 version 14.3.0 Release 14Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology

17、 2g3Foreword . 6g31 Scope 7g32 References 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 10g33.3 Abbreviations . 12g34 General test conditions and declarations 13g34.1 Measurement uncertainties and test requirements 13g34.1.1 General 13g34.1.2 Acceptable uncertainty

18、of Test System . 13g34.1.2.1 General 13g34.1.2.2 Measurement of transmitter 13g34.1.2.3 Measurement of receiver . 13g34.1.3 Interpretation of measurement results . 14g34.2 Conducted and radiated requirement reference points . 14g34.3 Base station classes for AAS BS 15g34.4 Regional requirements 15g3

19、4.5 Operating bands and band categories . 15g34.6 Channel arrangements 15g34.7 Requirements for AAS BS capable of multi-band operation . 15g34.8 AAS BS configurations 15g34.8.1 Transmit configurations 15g34.8.2 Receive configurations . 16g34.8.3 Power supply options 16g34.8.4 BS with integrated Iuan

20、t BS modem 16g34.9 Capability sets 17g34.10 Manufacturer declarations 17g34.11 Test signal configurations for testing . 20g34.11.1 General 20g34.11.2 Test signal configurations . 21g34.11.2.1 ATCR1: UTRA multicarrier operation . 21g34.11.2.1.1 General 21g34.11.2.1.2 ATCR1a generation . 21g34.11.2.1.

21、3 ATCR1b generation . 21g34.11.2.1.4 ATCR1 EIRP allocation 21g34.11.2.2 ANTCR1: UTRA FDD multicarrier non-contiguous operation 21g34.11.2.2.1 General 21g34.11.2.2.2 ANTCR1 generation 21g34.11.2.2.3 ANTCR1 EIRP allocation . 22g34.11.2.3 ATCR2: E-UTRA multicarrier operation 22g34.11.2.3.1 General 22g3

22、4.11.2.3.2 ATCR2a generation . 22g34.11.2.3.3 ATCR2b generation . 22g34.11.2.3.4 ATCR2 EIRP allocation 23g34.11.2.4 ANTCR2: E-UTRA multicarrier non-contiguous operation . 23g34.11.2.4.1 General 23g34.11.2.4.2 ANTCR2 generation 23g34.11.2.4.3 ANTCR2 EIRP allocation . 24g34.11.2.5 ATCR3: UTRA and E-UT

23、RA multi RAT operation 24g34.11.2.5.1 General 24g3ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)43GPP TS 37.145-2 version 14.3.0 Release 144.11.2.5.2 ATCR3a generation . 24g34.11.2.5.3 ATCR3b generation . 24g34.11.2.5.4 ATCR3 EIRP allocation 25g34.11.2.6 ANTCR3: UTRA and E-UTRA multi RAT non-contiguous op

24、eration 25g34.11.2.6.1 General 25g34.11.2.6.2 ANTCR3a generation 25g34.11.2.6.3 ANTCR3 EIRP allocation . 26g34.11.2.7 ATCR4: Single carrier for receiver tests . 26g34.11.2.7.1 ATCR4a generation . 26g34.11.2.7.2 ATCR4b generation . 26g34.11.2.7.3 ATCR4c generation . 26g34.11.2.7.4 ATCR4 EIRP allocati

25、on 26g34.11.2.8 Generation of MB-MSR test configurations . 26g34.11.2.8.1 ATCR5a: MB-MSR test configuration for full carrier allocation 26g34.11.2.8.2 ATCR5b: MB-MSR test configuration with high PSD per carrier 27g34.11.2.9 ATCR6: Single carrier for Transmitter tests . 28g34.11.2.9.1 ATCR6a generati

26、on . 28g34.11.2.9.2 ATCR6b generation . 28g34.11.2.9.3 ATCR6c generation . 28g34.11.2.9.4 ATCR6 EIRP allocation 28g34.12 RF channels and test models 29g34.12.1 RF channels 29g34.12.2 Test models . 29g34.13 Format and interpretation of tests . 30g34.14 Reference coordinate system 31g35 Applicability

27、of Requirements . 32g35.1 General . 32g35.2 Test configurations for AAS BS for operating bands where MSR with more than 1 RAT is supported . 33g35.3 Test configurations for multi-carrier capable AAS BS in operating bands where one RAT capability sets are supported 33g35.3.1 General 33g35.3.2 AAS BS

28、supporting one RAT only MSR in the operating band . 33g35.3.3 AAS BS supporting Single-RAT UTRA in the operating band 34g35.3.4 AAS BS supporting Single-RAT E-UTRA in the operating band 34g35.4 Test configurations for AAS BS operating bands with multi-band dependencies 35g35.4.1 AAS BS operating ban

29、ds with multi-band dependencies supporting MSR operation 35g35.4.2 AAS BS operating bands with multi-band dependencies supporting Single-RAT only . 35g36 Radiated transmitter characteristics 36g36.1 General . 36g36.2 Radiated Transmit Power . 36g36.2.1 Definition and applicability 36g36.2.2 Minimum

30、Requirement . 36g36.2.3 Test purpose 36g36.2.4 Method of test . 37g36.2.4.1 Initial conditions . 37g36.2.4.2 Procedure 37g36.2.5 Test Requirement 37g37 Radiated receiver characteristics 38g37.1 General . 38g37.2 OTA sensitivity 38g37.2.1 Definition and applicability 38g37.2.2 Minimum Requirement . 3

31、9g37.2.3 Test Purpose 39g37.2.4 Method of test . 39g37.2.4.1 Initial conditions . 39g37.2.4.2 Procedure 39g37.2.5 Test Requirements 40g37.2.5.1 General 40g37.2.5.2 UTRA FDD Test Requirements 40g37.2.5.3 UTRA TDD 1,28Mcp option Test Requirements . 40g3ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)53GPP TS

32、37.145-2 version 14.3.0 Release 147.2.5.4 E-UTRA Test Requirements . 40g3Annex A (normative): Test system characterization . 42g3Annex B (normative): Calibration 43g3Annex C (informative): Test tolerances and derivation of test requirements . 44g3C.1 General . 44g3C.2 Measurement of transmitter (OTA

33、) 44g3C.3 Measurement of receiver (OTA) 44g3Annex D (informative): Test system set-up 45g3D.1 Transmitter . 45g3D1.1 Radiated Transmit Power . 45g3D.2 Receiver 46g3D.2.1 OTA sensitivity 46g3Annex E (normative): Estimation of Measurement Uncertainty . 47g3E.1 General . 47g3E.2 Measurement methodology

34、 descriptions 47g3E.3 Measurement uncertainty budget format 47g3E.4 Measurement uncertainty budgets 47g3E.5 Measurement error contribution descriptions . 47g3Annex F (informative): Change history . 48g3History 49g3ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)63GPP TS 37.145-2 version 14.3.0 Release 14For

35、eword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will b

36、e re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the seco

37、nd digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)73GPP TS 37.145-2 version 14.3.0 Release 141 Scop

38、e The present document specifies radiated test methods and conformance requirements for single RAT E-UTRA operation, single RAT UTRA operation (FDD and TDD) and Multi-Standard Radio (MSR) UTRA and E-UTRA Active Antenna System (AAS) Base Station (BS). These have been derived from, and are consistent

39、with non-AAS BS specifications in 3GPP TS 25.104 2, 3GPP TS 25.105 3, 3GPP TS 36.104 4 or 3GPP TS 37.104 5. The technical specification 3GPP TS 37.145 is in 2 parts, part 3GPP TS 37.145-1 9 covers conducted requirements and part 3GPP TS 37.145-2 (the present document) covers radiated requirements. T

40、he present document does not establish radiated test methods and conformance requirements for Band 46 operation as it is not supported by AAS BS. Conducted Band 46 test requirements are still applicable for AAS BS for protection of and against Band 46 operation, as specified in 3GPP TS 37.145-1 9. 2

41、 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequ

42、ent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 2

43、1.905: “Vocabulary for 3GPP Specifications“. 2 3GPP TS 25.104: “Base Station (BS) radio transmission and reception (FDD)“. 3 3GPP TS 25.105: “Base Station (BS) radio transmission and reception (TDD)“. 4 3GPP TS 36.104: “Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio tra

44、nsmission and reception“. 5 3GPP TS 37.104: “E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station (BS) radio transmission and reception“. 6 3GPP TS 37.105: “Active Antenna System (AAS) Base Station (BS) transmission and reception“. 7 3GPP TR 37.842: “E-UTRA and UTRA; Radio Frequency (R

45、F) requirement background for Active Antenna System (AAS) Base Station (BS)“. 8 Recommendation ITU-R M.1545: “Measurement uncertainty as it applies to test limits for the terrestrial component of International Mobile Telecommunications-2000“. 9 3GPP TS 37.145-1: “Active Antenna System (AAS) Base Sta

46、tion (BS) conformance testing; Part 1: Conducted conformance testing“. 10 3GPP TS 25.141: “Base Station (BS) conformance testing (FDD)“. 11 3GPP TS 25.142: “Base Station (BS) conformance testing (TDD)“. 12 3GPP TS 36.141: “Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) confor

47、mance testing“. 13 3GPP TS 37.141: “E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station (BS) conformance testing“. ETSI ETSI TS 137 145-2 V14.3.0 (2018-01)83GPP TS 37.145-2 version 14.3.0 Release 143 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the presen

48、t document, the terms and definitions given in 3GPP TR 21.905 1 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in 3GPP TR 21.905 1. AAS BS receiver: composite receiver function of an AAS BS receiving in an operating band

49、 active antenna system base station: base station system which combines an Antenna Array with an Active transceiver unit array and a Radio Distribution Network band category: group of operating bands for which the same MSR scenarios apply Base Station RF Bandwidth: bandwidth in which a base station transmits and/or receives single or multiple carrier(s) and/or RATs simultaneously within a supported operating band NOTE: In single carrier operation, the Base Station RF Bandwidth is equal to the channel bandwidth. Base Station RF Bandwid