ETSI TS 127 005-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) LTE Use of Data Terminal Equipment - Data Circuitf.pdf

《ETSI TS 127 005-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) LTE Use of Data Terminal Equipment - Data Circuitf.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 127 005-2018 Digital cellular telecommunications system (Phase 2+) (GSM) Universal Mobile Telecommunications System (UMTS) LTE Use of Data Terminal Equipment - Data Circuitf.pdf（69页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 127 005 V15.0.0 (2018-06) Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); LTE; Use of Data Terminal Equipment - Data Circuit terminating Equipment (DTE - DCE) interface for Short Message Service (SMS) and Cell Broadcast Service

2、 (CBS) (3GPP TS 27.005 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 127 005 V15.0.0 (2018-06)13GPP TS 27.005 version 15.0.0 Release 15Reference RTS/TSGC-0127005vf00 Keywords GSM,LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fa

3、x: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic ver

4、sions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is

5、 the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is ava

6、ilable at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by

7、 any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all med

8、ia. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for th

9、e benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 127 005 V15.0.0 (2018-06)23GPP TS 27.005 version 15.0.0 Release 15Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables ma

10、y have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI s

11、tandards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs no

12、t referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of t

13、hese except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those

14、trademarks. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being refer

15、ences to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not

16、“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 127 005 V15.0.0 (2018-06)33GPP TS 27.005 ver

17、sion 15.0.0 Release 15Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 6g30 Scope 7g30.1 References 8g30.2 Abbreviations . 8g31 Reference configuration . 9g31.1 V.24 Interface Circuits . 9g31.1.1 Circuit definitions for the SMS Block mode 9g31.1.2 Circuit

18、definitions for the SMS Text and PDU modes . 10g32 SMS Block Mode . 10g32.1 Beginning and ending of SMS/CBS Block Mode 10g32.1.1 Beginning SMS/CBS Block Mode . 10g32.1.2 Returning from SMS/CBS Block Mode To Default Mode . 10g32.2 Protocol description 11g32.3 Requesting messages already held in the M

19、obile Termination 12g32.3.1 Requesting List Of Messages 12g32.3.2 Requesting Transfer Of Messages 12g32.3.2.1 Requesting Transfer Of A Specific Message 13g32.3.2.2 Requesting Transfer Of All Messages. 13g32.3.3 Requesting Diversion Of Incoming Messages 13g32.3.3.1 Requesting SMS Messages . 13g32.3.3

20、.2 Requesting CBS Messages 14g32.3.3.3 Requesting indication of message arrival 14g32.3.4 Requesting Transfer Into Mobile Termination . 14g32.3.5 Requesting Deletion Of Messages 15g32.4 Message functional definitions and contents 15g32.4.1 Commands Issued By The Terminal Equipment 16g32.4.1.1 List R

21、equest. 16g32.4.1.2 Get Message 16g32.4.1.3 Get First Message 17g32.4.1.4 Get Next Message . 17g32.4.1.5 Transfer Inc SMS 17g32.4.1.6 Indicate Inc SMS . 17g32.4.1.7 Transfer Inc CBS 17g32.4.1.8 Insert SMS. 17g32.4.1.9 Delete message 18g32.4.1.10 Unable to process 18g32.4.1.11 End SMS Mode . 18g32.4.

22、1.12 Acknowledge Message 18g32.4.2 Responses/Indications Issued By The MT 18g32.4.2.1 Message List . 18g32.4.2.2 Message. 19g32.4.2.3 Get Message Failure 19g32.4.2.4 Inc Message. 19g32.4.2.5 Message Arrived . 19g32.4.2.6 Insert SMS Complete 19g32.4.2.7 Insert SMS Failure 20g32.4.2.8 Delete Message C

23、omplete . 20g32.4.2.9 Delete Message Failure . 20g32.4.2.10 Unable To Process 20g32.4.2.11 End SMS Mode . 20g32.4.2.12 Request Confirmed 20g32.5 General message format and information elements coding 21g3ETSI ETSI TS 127 005 V15.0.0 (2018-06)43GPP TS 27.005 version 15.0.0 Release 152.5.1 Message Typ

24、e . 21g32.5.2 Other Information Elements . 22g32.5.2.1 Short Message Reference 22g32.5.2.2 SMS Transfer Type . 22g32.5.2.3 Indication Type . 23g32.5.2.4 Insert Type 24g32.5.2.5 Short Message Index . 25g32.5.2.6 Short Message Data. 26g32.5.2.7 Cause . 28g32.5.2.8 Index Count . 29g32.5.2.9 CBS Transfe

25、r Type . 29g32.5.2.10 Page Index . 29g32.5.2.11 Last Short Message . 30g32.5.2.12 Confirm Type 30g32.5.2.13 TP-Failure Cause . 31g32.5.2.14 SM-Deliver-Ack 31g32.5.2.15 SM-Submit-Ack 32g33 Text Mode 32g33.1 Parameter Definitions . 32g33.2 General Configuration Commands . 35g33.2.1 Select Message Serv

26、ice +CSMS . 35g33.2.2 Preferred Message Storage +CPMS 35g33.2.3 Message Format +CMGF . 36g33.2.4 Enter SMS Block Mode Protocol +CESP . 36g33.2.5 Message Service Failure Result Code +CMS ERROR . 37g33.2.6 Informative Examples. 37g33.3 Message Configuration Commands . 38g33.3.1 Service Centre Address

27、+CSCA . 38g33.3.2 Set Text Mode Parameters +CSMP 38g33.3.3 Show Text Mode Parameters +CSDH 38g33.3.4 Select Cell Broadcast Message Types +CSCB . 39g33.3.5 Save Settings +CSAS . 39g33.3.6 Restore Settings +CRES . 40g33.3.7 Informative Examples. 40g33.4 Message Receiving and Reading Commands . 41g33.4

28、.1 New Message Indications to TE +CNMI 41g33.4.2 List Messages +CMGL . 45g33.4.3 Read Message +CMGR 46g33.4.4 New Message Acknowledgement to ME/TA +CNMA 46g33.4.5 Informative Examples . 47g33.5 Message Sending and Writing Commands . 48g33.5.1 Send Message +CMGS . 48g33.5.2 Send Message from Storage

29、+CMSS 49g33.5.3 Write Message to Memory +CMGW . 49g33.5.4 Delete Message +CMGD 50g33.5.5 Send Command +CMGC 50g33.5.6 More Messages to Send +CMMS . 51g33.5.7 Informative Examples . 51g34 PDU Mode 52g34.0 General . 52g34.1 List Messages +CMGL 53g34.2 Read Message +CMGR 53g34.3 Send Message +CMGS 53g3

30、4.4 Write Message to Memory +CMGW . 54g34.5 Send Command +CMGC . 54g34.6 New Message Acknowledgement to ME/TA +CNMA 55g34.7 Send Message from Storage +CMSS . 56g3Annex A (normative): Character Set Conversions for SMS Text Mode . 57g3Annex B (informative): Example of processing a data block . 60g3ETS

31、I ETSI TS 127 005 V15.0.0 (2018-06)53GPP TS 27.005 version 15.0.0 Release 15B.1 Example state diagrams for the block receiver. 60g3B.2 Example of coding and decoding a data block . 60g3Annex C (informative): Change History 67g3History 68g3ETSI ETSI TS 127 005 V15.0.0 (2018-06)63GPP TS 27.005 version

32、 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the presen

33、t document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 Indicates TSG approved document under change control.

34、y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the specification; ETSI ETSI TS 127 005 V15.0.0 (2018-06)73GPP TS 27.005 version 15.0.0 Relea

35、se 150 Scope The present document defines three interface protocols for control of SMS functions within a GSM/UMTS mobile telephone from a remote terminal via an asynchronous interface. Clause 2 defines a binary protocol (“Block Mode“). The protocol includes error protection and is suitable for use

36、where the link may not be completely reliable. It will be of particular use where control of remote devices is required. Efficient transfer of binary encoded user data is possible. Clause 3 defines a character-based interfaced based on “AT“ commands (“Text Mode“). This mode is suitable for unintelli

37、gent terminals or terminal emulators, and for application software built on command structures like those defined in V.25ter. Some of the commands defined in clause 3 will also be useful for implementations of clause 2 and/or clause 4, for example enabling an indication of incoming SMS messages. Cla

38、use 4 defines a character-based interface with hex-encoded binary transfer of message blocks (“PDU Mode“). This mode is suitable for software drivers based on AT command structures which do not understand the content of the message blocks and can only pass them between the MT and “upper level“ softw

39、are resident in the TE. In all three modes, the terminal is considered to be in control for SMS/CBS transactions. The present document considers the mobile termination to be a single entity. Other 3GPP/GSM Technical Specifications describe the split of functionality between the mobile equipment and

40、(U)SIM. The three “modes“ referred to above, are represented in figure 0.1. The “Block mode“ is a self contained mode in its own right, and when entered, control will remain within that mode until the procedures to exit the mode are executed, after which control is returned to the V.25ter “command“

41、state or “on-line command“ state. The “Text“ and “PDU“ modes are not in themselves V.25ter states but are simply sets of commands which will operate in either the V.25ter “command“ state or “on-line command“ state. The “Text“ and “PDU“ modes are transitory states and after each operation, control is

42、 automatically returned to the V.25ter “command“ state or “on-line command“ state. Whilst in the V.25ter command state, the MS is available to handle incoming and outgoing calls such as Data or Facsimile. SMSTextModeSMSPDUModeSMS Block ModeV.25ter“command“ stateand “on-line command“ stateFigure 0.1:

43、 Block, Text and PDU modes In the “Block mode“ and “PDU“ mode a mobile is not permitted to modify any component of an SMS/CBS message received from the air interface or an SMS message received from a TE, before passing it on, except where 3GPP TS 23.040 3 or 3GPP TS 23.041 4 defines a “component mod

44、ification facility“ and where this “component modification facility“ is supported by the mobile. In the Text Mode the mobile may be unable to display characters coded in particular coding schemes. In this case, the mobile shall behave as described in 3GPP TS 23.038 2 and assume the coding scheme to

45、be the GSM 7 bit default alphabet. ETSI ETSI TS 127 005 V15.0.0 (2018-06)83GPP TS 27.005 version 15.0.0 Release 150.1 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identifi

46、ed by date of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific refere

47、nce implicitly refers to the latest version of that document in the same Release as the present document. 1 Void. 2 3GPP TS 23.038: “Alphabets and language-specific information“. 3 3GPP TS 23.040: “Technical realization of the Short Message Service (SMS) “. 4 3GPP TS 23.041: “Technical realization o

48、f the Cell Broadcast Service (CBS)“. 5 3GPP TS 24.008: “Mobile Radio Interface Layer 3 specification; Core Network Protocols; Stage 3“. 6 3GPP TS 24.011: “Short Message Service (SMS) support on mobile radio interface“. 7 3GPP TS 24.012: “Cell Broadcast Service (CBS) support on the mobile radio inter

49、face“. 8 3GPP TS 27.001: “General on Terminal Adaptation Functions (TAF) for Mobile Stations (MS)“. 9 3GPP TS 27.007: “AT command set for User Equipment (UE)“. 10 3GPP TS 51.011: “Specification of the Subscriber Identity Module - Mobile Equipment (SIM - ME) interface“. 11 ITU-T Recommendation V.25ter: “Serial asynchronous automatic dialling and control“. 12 ITU-T Recommendation V.24: “List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE)“. 13 ITU-T Recommendation E.164: “T