ETSI TS 125 143-2018 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V15 0 0 3GPP TS 25 143 version 15 0 0 Release 15).pdf

《ETSI TS 125 143-2018 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V15 0 0 3GPP TS 25 143 version 15 0 0 Release 15).pdf》由会员分享，可在线阅读，更多相关《ETSI TS 125 143-2018 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V15 0 0 3GPP TS 25 143 version 15 0 0 Release 15).pdf（85页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 125 143 V15.0.0 (2018-07) Universal Mobile Telecommunications System (UMTS); UTRA repeater conformance testing (3GPP TS 25.143 version 15.0.0 Release 15) TECHNICAL SPECIFICATION ETSI ETSI TS 125 143 V15.0.0 (2018-07)13GPP TS 25.143 version 15.0.0 Release 15Reference RTS/TSGR-0425143vf00 Key

2、words UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be download

3、ed from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing o

4、r perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject t

5、o revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People

6、/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the wri

7、tten authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETMare trademarks of ETSI registere

8、d for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 125 143 V15.0.0 (2018-07)23GPP TS 25.143 version 15.0.0 Release 15Contents 1

9、 Scope 6g32 References 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 (void) 7g33.3 Abbreviations . 7g34 Frequency bands and channel arrangement 8g34.1 Frequency bands . 8g34.2 TX RX frequency separation . 8g34.3 Channel arrangement 9g34.3.1 Channel spacing 9g34.3.2 Channel

10、raster . 9g34.3.3 Channel number 9g35 General test conditions and declarations 11g35.1 Acceptable uncertainty of Test System 12g35.1.1 Measurements of test environments 12g35.1.2 Measurements of Repeater 13g35.2 Repeater test tolerances (informative) 15g35.3 Interpretation of measurement results 16g

11、35.4 Test Environment . 16g35.4.1 Normal test environment 16g35.4.2 Extreme test environment . 17g35.4.2.1 Extreme temperature . 17g35.4.3 Vibration . 17g35.4.4 Power supply 17g35.5 Selection of configurations for testing 18g35.6 Regional requirements 19g35.7 Test Models 20g35.8 Format and interpret

12、ation of tests . 20g35.9 Repeater configurations 21g35.9.1 Power supply options 21g35.9.2 Combining of Repeaters . 21g36 Output power 21g36.1 Maximum output power . 21g36.1.1 Definition and applicability 21g36.1.2 Minimum Requirements . 21g36.1.3 Test purpose 22g36.1.4 Method of test . 22g36.1.4.1 I

13、nitial conditions . 22g36.1.4.2 Procedure 22g36.1.5 Test Requirements 22g37 Frequency stability . 23g37.1 Definition and applicability 23g37.2 Minimum Requirement 23g37.3 Test purpose . 23g37.4 Method of test . 23g37.4.1 Initial conditions . 23g37.4.2 Procedure 23g37.5 Test requirements . 24g38 Out

14、of band gain . 24g38.1 Definitions and applicability 24g38.2 Minimum Requirements . 24g38.3 Test purpose . 24g38.4 Method of test . 24g3ETSI ETSI TS 125 143 V15.0.0 (2018-07)33GPP TS 25.143 version 15.0.0 Release 158.4.1 Initial conditions . 24g38.4.2 Procedure 25g38.5 Test requirements . 25g39 Unwa

15、nted emission 25g39.1 Out of band emission 26g39.1.1 Void 26g39.1.2 Operating band unwanted emissions 26g39.1.2.1 Definitions and applicability . 26g39.1.2.2 Minimum Requirements 26g39.1.2.3 Test purpose 30g39.1.2.4 Method of test . 30g39.1.2.4.1 Initial conditions 30g39.1.2.4.2 Procedures . 30g39.1

16、.2.5 Test requirements 30g39.1.3 Protection of BS receiver in the operating band . 33g39.1.3.1 Minimum Requirement . 33g39.1.4 Co-existence with services in adjacent frequency bands 34g39.1.4.1 Minimum requirement 34g39.2 Spurious emissions . 34g39.2.1 Definition and applicability 34g39.2.2 Minimum

17、Requirements . 34g39.2.2.1 Spurious emission (Category A) . 34g39.2.2.2 Spurious emission (Category B) . 35g39.2.2.3 Void. 36g39.2.2.4 Co-existence with other systems in the same geographical area . 36g39.2.2.4.1 Minimum Requirements 37g39.2.2.5 Co-existence with co-located and co-sited base station

18、s . 40g39.2.2.5.1 Minimum Requirements 41g39.2.2.6 Co-existence with PHS . 44g39.2.2.6.1 Minimum requirement. 44g39.2.2.7 Co-existence with UTRA-TDD and/or E-UTRA TDD . 45g39.2.2.7.1 Operation in the same geographic area 45g39.2.2.7.2 Co-located Repeaters and UTRA-TDD and/or E-UTRA TDD base stations

19、 46g39.2.2.8 (Void) 49g39.2.2.9 Protection of public safety operations . 49g39.2.2.9.1 Minimum Requirement . 49g39.2.3 Test purpose 49g39.2.4 Method of test . 49g39.2.4.1 Initial conditions . 49g39.2.4.2 Procedures . 50g39.2.5 Test requirements 50g310 Modulation accuracy 50g310.1 Error vector magnit

20、ude . 50g310.1.1 Definition and applicability 50g310.1.2 Minimum Requirements . 50g310.1.3 Test purpose 50g310.1.4 Method of test . 50g310.1.4.1 Initial conditions . 50g310.1.4.2 Procedure 51g310.1.4.3 Stimulus EVM effect. 51g310.1.5 Test requirements 51g310.2 Peak code domain error 51g310.2.1 Defin

21、ition and applicability 51g310.2.2 Minimum Requirements . 51g310.2.3 Test purpose 51g310.2.4 Method of test . 51g310.2.4.1 Initial conditions . 51g310.2.4.2 Procedure 51g310.2.5 Test requirements 51g310.3 Relative Code Domain Error (RCDE) for 64QAM modulation . 52g3ETSI ETSI TS 125 143 V15.0.0 (2018

22、-07)43GPP TS 25.143 version 15.0.0 Release 1510.3.1 Definition and applicability 52g310.3.2 Minimum requirement 52g310.3.3 Test purpose 52g310.3.4 Method of test . 52g310.3.4.1 Initial conditions . 52g310.3.4.2 Procedure 52g310.3.5 Test requirements 52g311 Input intermodulation . 52g311.1 Definition

23、 and applicability 52g311.2 Minimum Requirements . 53g311.2.1 General requirement . 53g311.2.2 Co-location with BS in other systems . 53g311.2.3 Co-existence with other systems . 58g311.3 Test purpose . 62g311.4 Method of test . 62g311.4.1 Initial conditions . 62g311.4.2 Procedure 63g311.5 Test requ

24、irements . 63g311.5.1 Mandatory requirement . 63g311.5.2 Co-location with BS in other systems . 63g311.5.3 Co-existence with other systems . 68g312 Output intermodulation 72g312.1 Definition and applicability 72g312.2 Minimum requirement 73g312.3 Test purpose . 73g312.4 Method of test . 73g312.4.1 I

25、nitial conditions . 73g312.4.2 Procedures. 73g312.5 Test requirements . 73g313 Adjacent Channel Rejection Ratio (ACRR) . 74g313.1 Definitions and applicability 74g313.2 Minimum Requirements . 74g313.3 Test purpose . 74g313.4 Method of test . 74g313.4.1 Initial conditions . 74g313.4.2 Procedure 74g31

26、3.4.3 Test Requirements 75g3Annex A (informative): Repeater measurement system set-up 76g3A.1 Maximum output power . 76g3A.2 Frequency stability . 76g3A.3 Out of band gain . 76g3A.4 Unwanted emission: Spectrum emission mask 76g3A.5 Unwanted emission: Spurious emission . 77g3A.6 Modulation Accuracy:

27、Error Vector Magnitude 77g3A.7 Modulation Accuracy: Peak Code Domain Error Error and Relative Coder Domain Error 77g3A.8 Input inter modulation 78g3A.9 Output Intermodulation 78g3Annex B (informative): Derivation of Test Requirements 79g3Annex C (informative): Acceptable uncertainty of Test Equipmen

28、t . 81g3Annex D (informative): Change History 82g3ETSI ETSI TS 125 143 V15.0.0 (2018-07)53GPP TS 25.143 version 15.0.0 Release 15History 84g3ETSI ETSI TS 125 143 V15.0.0 (2018-07)63GPP TS 25.143 version 15.0.0 Release 15Foreword This Technical Specification has been produced by the 3rdGeneration Par

29、tnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an in

30、crease in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. Y the second digit is incremented for all changes of substance, i.e. technical enhancem

31、ents, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. 1 Scope The present document specifies the Radio Frequency (RF) test methods and Minimum Requirements for UTRA FDD Repeaters. These have been derived from, and are co

32、nsistent with the UTRA FDD Repeater specifications defined in TS 25.106. This document establishes the minimum RF characteristics of the UTRA FDD Repeater. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. Re

33、ferences are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GS

34、M document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 25.104: “UTRA(BS) FDD; Radio transmission and Reception“. 2 3GPP TS 25.942: “RF system scenarios“. 3 3GPP TS 25.113 : “Base station EMC“. 4 ITU-R reco

35、mmendation SM.329: “Unwanted emissions in the spurious domain “. 5 ITU-T recommendation O.153: “Basic parameters for the measurement of error performance at bit rates below the primary rate“. 6 IEC 60721-3-3 (1994): “Classification of environmental conditions Part 3: Classification of groups of envi

36、ronmental parameters and their severities Section 3: Stationary use at weather protected locations“. ETSI ETSI TS 125 143 V15.0.0 (2018-07)73GPP TS 25.143 version 15.0.0 Release 157 IEC 60721-3-4 (1995): “Classification of environmental conditions Part 3: Classification of groups of environmental pa

37、rameters and their severities Section 4: Stationary use at non-weather protected locations“. 8 IEC 60068-2-1 (1990): “Environmental testing Part 2: Tests. Tests A: Cold“. 9 IEC 60068-2-2 (1974): “Environmental testing Part 2: Tests. Tests B: Dry heat“. 10 IEC 60068-2-6 (1995): “Environmental testing

38、 Part 2: Tests Test Fc: Vibration (sinusoidal)“. 11 3GPP TS 25.141: “Base station conformance testing (FDD)“. 12 3GPP TS 25.106: “UTRA Repeater; Radio transmission and reception“. 13 3GPP TS 36.143: “Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater conformance testing“ 14 CEPT ECC D

39、ecision (13)03, “The harmonised use of the frequency band 1452-1492 MHz for Mobile/Fixed Communications Networks Supplemental Downlink (MFCN SDL)“. 15 3GPP TS 36.104: “Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio transmission and reception“. 3 Definitions, symbols and

40、 abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Donor coupling loss: is the coupling loss between the repeater and the donor base station. Down-link: signal path where base station transmits and mobile receives Maximum output power,

41、 Pmax: This is the mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition. Operating band: the frequency range in which UTRA FDD operates, that is defined with a specific set of technical requirements. NOTE 1: The operating band(s) for an UTRA

42、 Repeater is declared by the manufacturer according to the designations in clause 4.1, Table 4.1. NOTE 2: Unless specified, operating band refers to the uplink operating band and downlink operating band. Pass band: the pass band is the frequency range in which the Repeater operates in with operation

43、al configuration. This frequency range can correspond to one or several consecutive nominal 5 MHz channels. If they are not consecutive each subset of channels shall be considered as an individual pass band. A repeater can have one or several pass bands. Repeater: a device that receives, amplifies a

44、nd transmits the radiated or conducted RF carrier both in the down-link direction (from the base station to the mobile area) and in the up-link direction (from the mobile to the base station). In operating bands specified with only down-link or up-link, only the up-link or down-link as specified for

45、 the operating band is repeated. Up-link: signal path where mobile transmits and base station receives. 3.2 (void) 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BS Base Transceiver Station CW Continuous Wave (unmodulated signal) DL Down Link (forward

46、link) ETSI ETSI TS 125 143 V15.0.0 (2018-07)83GPP TS 25.143 version 15.0.0 Release 15DTT Digital Terrestrial Television EIRP Effective Isotropic Radiated Power EVM Error Vector Magnitude FDD Frequency Division Duplex FFS For Further Study IMT2000 International Mobile Telecommunication-2000 ITU Inter

47、national Telecommunication Union MS Mobile Station RCDE Relative Code Domain Error RF Radio Frequency RSS Root Sum of the Squares TDD Time Division Duplex UARFCN UTRA Absolute Radio Frequency Channel Number UL Up Link (reverse link) UMTS Universal Mobile Telecommunication System UTRA Universal Terre

48、strial Radio Access WCDMA Wide band Code Division Multiple Access 4 Frequency bands and channel arrangement 4.1 Frequency bands a) A UTRA/FDD Repeater is designed to operate in one or several pass bands within either of the following operating bands; Table 4.1: Frequency bands Operating Band UL Freq

49、uencies UE transmit, Node B receive DL frequencies UE receive, Node B transmit I 1920 1980 MHz 2110 -2170 MHz II 1850 -1910 MHz 1930 -1990 MHz III 1710 1785 MHz 1805 1880 MHz IV 1710 1755 MHz 2110 2155 MHz V 824 849MHz 869 894MHz VI 830 840 MHz 875 885 MHz VII 2500 2570 MHz 2620 2690 MHz VIII 880 915 MHz 925 960 MHz IX 1749.9 1784.9 MHz 1844.9 1879.9 MHz X 1710 1770 MHz 2110 2170 MHz XI 1427.9 1452.9 MHz 1475.9 1500.9 MHz XII 698 - 716 MHz 728 - 746 MHz XIII 777 - 787 MHz 746 - 756 MHz XI