ETSI TS 125 143-2016 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V13 0 0 3GPP TS 25 143 version 13 0 0 Release 13)《通用移动通信系统(UMTS) 通用陆地无线接入中.pdf

《ETSI TS 125 143-2016 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V13 0 0 3GPP TS 25 143 version 13 0 0 Release 13)《通用移动通信系统(UMTS) 通用陆地无线接入中.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 125 143-2016 Universal Mobile Telecommunications System (UMTS) UTRA repeater conformance testing (V13 0 0 3GPP TS 25 143 version 13 0 0 Release 13)《通用移动通信系统(UMTS) 通用陆地无线接入中.pdf（83页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 1Universal Mobile TelUTRA repe(3GPP TS 25.1TECHNICAL SPECIFICATION125 143 V13.0.0 (2016elecommunications System (peater conformance testing .143 version 13.0.0 Release 1316-01) (UMTS); 13) ETSI ETSI TS 125 143 V13.0.0 (2016-01)13GPP TS 25.143 version 13.0.0 Release 13Reference RTS/TSGR-0425

2、143vd00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can

3、be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

4、 existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may b

5、e subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/Peopl

6、e/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the wr

7、itten authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GP

8、PTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 125 143 V13.0.0 (2016-01)23GPP TS 25.143 version 13.0.0 Release 13Intellectual Propert

9、y Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Esse

10、ntial, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried

11、out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generati

12、on Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and

13、 ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting R

14、ules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 143 V13.0.0 (2016-01)33GPP TS 25.143 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs term

15、inology 2g31 Scope 8g32 References 8g33 Definitions, symbols and abbreviations . 9g33.1 Definitions 9g33.2 (void) 9g33.3 Abbreviations . 9g34 Frequency bands and channel arrangement 10g34.1 Frequency bands . 10g34.2 TX RX frequency separation . 10g34.3 Channel arrangement 11g34.3.1 Channel spacing 1

16、1g34.3.2 Channel raster . 11g34.3.3 Channel number 11g35 General test conditions and declarations 13g35.1 Acceptable uncertainty of Test System 14g35.1.1 Measurements of test environments 14g35.1.2 Measurements of Repeater 15g35.2 Repeater test tolerances (informative) 16g35.3 Interpretation of meas

17、urement results 17g35.4 Test Environment . 18g35.4.1 Normal test environment 18g35.4.2 Extreme test environment . 18g35.4.2.1 Extreme temperature . 18g35.4.3 Vibration . 19g35.4.4 Power supply 19g35.5 Selection of configurations for testing 19g35.6 Regional requirements 20g35.7 Test Models 21g35.8 F

18、ormat and interpretation of tests . 21g35.9 Repeater configurations 22g35.9.1 Power supply options 22g35.9.2 Combining of Repeaters . 22g36 Output power 22g36.1 Maximum output power . 22g36.1.1 Definition and applicability 22g36.1.2 Minimum Requirements . 22g36.1.3 Test purpose 23g36.1.4 Method of t

19、est . 23g36.1.4.1 Initial conditions . 23g36.1.4.2 Procedure 23g36.1.5 Test Requirements 23g37 Frequency stability . 24g37.1 Definition and applicability 24g37.2 Minimum Requirement 24g37.3 Test purpose . 24g37.4 Method of test . 25g37.4.1 Initial conditions . 25g37.4.2 Procedure 25g3ETSI ETSI TS 12

20、5 143 V13.0.0 (2016-01)43GPP TS 25.143 version 13.0.0 Release 137.5 Test requirements . 25g38 Out of band gain . 25g38.1 Definitions and applicability 25g38.2 Minimum Requirements . 25g38.3 Test purpose . 26g38.4 Method of test . 26g38.4.1 Initial conditions . 26g38.4.2 Procedure 26g38.5 Test requir

21、ements . 26g39 Unwanted emission 27g39.1 Out of band emission 27g39.1.1 Void 27g39.1.2 Operating band unwanted emissions 27g39.1.2.1 Definitions and applicability . 27g39.1.2.2 Minimum Requirements 28g39.1.2.3 Test purpose 31g39.1.2.4 Method of test . 31g39.1.2.4.1 Initial conditions 31g39.1.2.4.2 P

22、rocedures . 32g39.1.2.5 Test requirements 32g39.1.3 Protection of BS receiver in the operating band . 35g39.1.3.1 Minimum Requirement . 35g39.1.4 Co-existence with services in adjacent frequency bands 36g39.1.4.1 Minimum requirement 36g39.2 Spurious emissions . 36g39.2.1 Definition and applicability

23、 36g39.2.2 Minimum Requirements . 36g39.2.2.1 Spurious emission (Category A) . 36g39.2.2.2 Spurious emission (Category B) . 37g39.2.2.3 Void. 38g39.2.2.4 Co-existence with other systems in the same geographical area . 38g39.2.2.4.1 Minimum Requirements 39g39.2.2.5 Co-existence with co-located and co

24、-sited base stations . 42g39.2.2.5.1 Minimum Requirements 43g39.2.2.6 Co-existence with PHS . 45g39.2.2.6.1 Minimum requirement. 46g39.2.2.7 Co-existence with UTRA-TDD and/or E-UTRA TDD . 46g39.2.2.7.1 Operation in the same geographic area 46g39.2.2.7.2 Co-located Repeaters and UTRA-TDD and/or E-UTR

25、A TDD base stations 48g39.2.2.8 (Void) 50g39.2.2.9 Protection of public safety operations . 50g39.2.2.9.1 Minimum Requirement . 50g39.2.3 Test purpose 50g39.2.4 Method of test . 50g39.2.4.1 Initial conditions . 50g39.2.4.2 Procedures . 51g39.2.5 Test requirements 51g310 Modulation accuracy 51g310.1

26、Error vector magnitude . 51g310.1.1 Definition and applicability 51g310.1.2 Minimum Requirements . 51g310.1.3 Test purpose 52g310.1.4 Method of test . 52g310.1.4.1 Initial conditions . 52g310.1.4.2 Procedure 52g310.1.4.3 Stimulus EVM effect. 52g310.1.5 Test requirements 52g310.2 Peak code domain err

27、or 52g310.2.1 Definition and applicability 52g310.2.2 Minimum Requirements . 52g3ETSI ETSI TS 125 143 V13.0.0 (2016-01)53GPP TS 25.143 version 13.0.0 Release 1310.2.3 Test purpose 52g310.2.4 Method of test . 53g310.2.4.1 Initial conditions . 53g310.2.4.2 Procedure 53g310.2.5 Test requirements 53g310

28、.3 Relative Code Domain Error (RCDE) for 64QAM modulation . 53g310.3.1 Definition and applicability 53g310.3.2 Minimum requirement 53g310.3.3 Test purpose 53g310.3.4 Method of test . 53g310.3.4.1 Initial conditions . 53g310.3.4.2 Procedure 54g310.3.5 Test requirements 54g311 Input intermodulation .

29、54g311.1 Definition and applicability 54g311.2 Minimum Requirements . 54g311.2.1 General requirement . 54g311.2.2 Co-location with BS in other systems . 54g311.2.3 Co-existence with other systems . 58g311.3 Test purpose . 61g311.4 Method of test . 61g311.4.1 Initial conditions . 61g311.4.2 Procedure

30、 62g311.5 Test requirements . 62g311.5.1 Mandatory requirement . 62g311.5.2 Co-location with BS in other systems . 62g311.5.3 Co-existence with other systems . 66g312 Output intermodulation 69g312.1 Definition and applicability 69g312.2 Minimum requirement 70g312.3 Test purpose . 70g312.4 Method of

31、test . 70g312.4.1 Initial conditions . 70g312.4.2 Procedures. 70g312.5 Test requirements . 70g313 Adjacent Channel Rejection Ratio (ACRR) . 71g313.1 Definitions and applicability 71g313.2 Minimum Requirements . 71g313.3 Test purpose . 71g313.4 Method of test . 71g313.4.1 Initial conditions . 71g313.

32、4.2 Procedure 71g313.4.3 Test Requirements 72g3Annex A (informative): Repeater measurement system set-up 73g3A.1 Maximum output power . 73g3A.2 Frequency stability . 73g3A.3 Out of band gain . 73g3A.4 Unwanted emission: Spectrum emission mask 73g3A.5 Unwanted emission: Spurious emission . 74g3A.6 Mo

33、dulation Accuracy: Error Vector Magnitude 74g3A.7 Modulation Accuracy: Peak Code Domain Error Error and Relative Coder Domain Error 74g3A.8 Input inter modulation 75g3A.9 Output Intermodulation 75g3ETSI ETSI TS 125 143 V13.0.0 (2016-01)63GPP TS 25.143 version 13.0.0 Release 13Annex B (informative):

34、Derivation of Test Requirements . 76g3Annex C (informative): Acceptable uncertainty of Test Equipment . 79g3Annex D (informative): Change History 80g3History 82g3ETSI ETSI TS 125 143 V13.0.0 (2016-01)73GPP TS 25.143 version 13.0.0 Release 13Foreword This Technical Specification has been produced by

35、the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of r

36、elease date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. Y the second digit is incremented for all changes of substance, i.

37、e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 143 V13.0.0 (2016-01)83GPP TS 25.143 version 13.0.0 Release 131 Scope The present document specifies the Radio Frequency (RF) te

38、st methods and Minimum Requirements for UTRA FDD Repeaters. These have been derived from, and are consistent with the UTRA FDD Repeater specifications defined in TS 25.106. This document establishes the minimum RF characteristics of the UTRA FDD Repeater. 2 References The following documents contain

39、 provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific

40、reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 25.104: “UTRA(BS) FDD; Radio transmission and Rece

41、ption“. 2 3GPP TS 25.942: “RF system scenarios“. 3 3GPP TS 25.113 : “Base station EMC“. 4 ITU-R recommendation SM.329: “Unwanted emissions in the spurious domain “. 5 ITU-T recommendation O.153: “Basic parameters for the measurement of error performance at bit rates below the primary rate“. 6 IEC 60

42、721-3-3 (1994): “Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 3: Stationary use at weather protected locations“. 7 IEC 60721-3-4 (1995): “Classification of environmental conditions Part 3: Classification of group

43、s of environmental parameters and their severities Section 4: Stationary use at non-weather protected locations“. 8 IEC 60068-2-1 (1990): “Environmental testing Part 2: Tests. Tests A: Cold“. 9 IEC 60068-2-2 (1974): “Environmental testing Part 2: Tests. Tests B: Dry heat“. 10 IEC 60068-2-6 (1995): “

44、Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal)“. 11 3GPP TS 25.141: “Base station conformance testing (FDD)“. 12 3GPP TS 25.106: “UTRA Repeater; Radio transmission and reception“. 13 3GPP TS 36.143: “Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater conformance t

45、esting“ 14 CEPT ECC Decision (13)03, “The harmonised use of the frequency band 1452-1492 MHz for Mobile/Fixed Communications Networks Supplemental Downlink (MFCN SDL)“. 15 3GPP TS 36.104: “Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio transmission and reception“. ETSI

46、ETSI TS 125 143 V13.0.0 (2016-01)93GPP TS 25.143 version 13.0.0 Release 133 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Donor coupling loss: is the coupling loss between the repeater and the donor base st

47、ation. Down-link: signal path where base station transmits and mobile receives Maximum output power, Pmax: This is the mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition. Operating band: the frequency range in which UTRA FDD operates, that

48、 is defined with a specific set of technical requirements. NOTE 1: The operating band(s) for an UTRA Repeater is declared by the manufacturer according to the designations in clause 4.1, Table 4.1. NOTE 2: Unless specified, operating band refers to the uplink operating band and downlink operating ba

49、nd. Pass band: the pass band is the frequency range in which the Repeater operates in with operational configuration. This frequency range can correspond to one or several consecutive nominal 5 MHz channels. If they are not consecutive each subset of channels shall be considered as an individual pass band. A repeater can have one or several pass bands. Repeater: a device that receives, amplifies and transmits the radiated or conducted RF carrier both in the down-link direction (from the base station to the mobile area) and