ETSI TS 103 241-1-2015 Integrated broadband cable telecommunication networks (CABLE) Testing Conformance test specifications for DS-Lite technology Part 1 Protocol Implementation C_1.pdf

《ETSI TS 103 241-1-2015 Integrated broadband cable telecommunication networks (CABLE) Testing Conformance test specifications for DS-Lite technology Part 1 Protocol Implementation C_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 103 241-1-2015 Integrated broadband cable telecommunication networks (CABLE) Testing Conformance test specifications for DS-Lite technology Part 1 Protocol Implementation C_1.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 103 241-1 V1.1.1 (2015-01) Integrated broadband cable telecommunication networks (CABLE); Testing; Conformance test specifications for DS-Lite technology; Part 1: Protocol Implementation Conformance Statement (PICS) proforma TECHNICAL SPECIFICATION ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)2Re

2、ference DTS/CABLE-00013-1 Keywords CABLE, IPCable, IPv6 ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Importan

3、t notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETS

4、I. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that t

5、he document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/porta

6、l.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified witho

7、ut the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Mem

8、bers. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)3Contents Intellectual Property Rights 4g3Foreword

9、. 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Conformance requirement concerning PICS 6g3Annex A (normative): DS-LITE PICS Proforma 7g3A.1 Guidanc

10、e for completing the PICS proforma . 7g3A.1.1 Purposes and structure 7g3A.1.2 Abbreviations and conventions 7g3A.1.3 Instructions for completing the PICS proforma 9g3A.2 Identification of the implementation 9g3A.2.1 Date of the statement 9g3A.2.2 Implementation Under Test (IUT) identification . 9g3A

11、.2.3 System Under Test (SUT) identification 9g3A.2.4 Product supplier 10g3A.2.5 Client (if different from product supplier) 10g3A.2.6 PICS contact person . 11g3A.3 Identification of the protocol 11g3A.4 Global statement of conformance . 11g3A.5 Tables . 12g3A.5.1 Transition Hardware . 12g3A.5.2 Init

12、ialization procedures . 12g3A.5.3 Fragmentation Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no invest

13、igation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specifi

14、cation (TS) has been produced by ETSI Technical Committee Integrated broadband cable telecommunication networks (CABLE). The present document produced for the transition technologies accommodates an urgent need in the industry to define requirements that enable seamless transition of Cable Networks

15、to IPv6. Considering the depletion of IPv4 addresses, transition to IPv6 is required in order to enable continued growth of the customer base connected to Cable Networks and ensure service continuity for existing and new customers. High-quality connectivity to all kinds of IP-based services and netw

16、orks is essential in todays business and private life. A plethora of transition technologies have been proposed in IETF, other standardization organizations and by manufacturers of IP technology to allow coexistence of IPv4 and IPv6 hosts, access and core networks as well as services. Each of these

17、technology options is specified, implemented and deployed in various forms and stages. The present document is based on the requirements ETSI TS 101 569-1 1. The present document is part 1 of a multi-part deliverable covering the conformance test specification for DS-Lite technology. Part 1: “Protoc

18、ol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and Protocol Implementation extra Information for Testing (PIXIT)“. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “shoul

19、d not“, “may“, “may not“, “need“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct cita

20、tion. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)51 Scope The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for conformance test specifications for the IPv6 transition technology DS-Lite as defined in ETSI TS 101 569-1 1 in compliance with the relevant requi

21、rements and in accordance with the relevant guidance given in ISO/IEC 9646-7 3. A supplier of an implementation which is claimed to conform to ETSI TS 101 569-1 1 is required to complete a copy of the PICS proforma provided in the annex A of present document. 2 References 2.1 Normative references Re

22、ferences are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced

23、documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced docume

24、nts are necessary for the application of the present document. 1 ETSI TS 101 569-1 (V1.1.1) (2013-10): “Integrated Broadband Cable Telecommunication Networks (CABLE); Cable Network Transition to IPv6 Part 1: IPv6 Transition Requirements“. 2 ISO/IEC 9646-1 (1994): “Information technology - Open Syste

25、ms Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 3 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 4 IETF RFC 6333: “Dual-Sta

26、ck Lite Broadband Deployments Following IPv4 Exhaustion“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the l

27、atest version of the reference document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the presen

28、t document but they assist the user with regard to a particular subject area. Not applicable. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)63 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions given in ETSI TS 101 569-1 1, ISO/IEC 96

29、46-1 2 and ISO/IEC 9646-7 3 apply. In particular, the following terms given in ISO/IEC 9646-1 2 apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implement

30、ed. The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an implementation or system claim

31、ed to conform to a given protocol specification 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AFTR Address Family Transition Router ALG Application Layer Gateway ATS Abstract Test Suite B4 (DS-Lite) Basic Bridging Broadband element CPE Customer Premis

32、es Equipment DNS Domain Name System DS-Lite Dual Stack Lite FTP File Transfer Protocol GRT Global Routing Table GW Gateway ICS Implementation Conformance Statement IP Internet ProtocolIPv4 IP version 4 IPv6 IP version 6 IUT Implementation Under Test MSS (TCP) Maximum Segment Size MTU Maximum Transmi

33、ssion Unit NAT Network Address Translation/Network Address Translator PDU Protocol Data Unit PICS Protocol Information Conformance Statement SUT System Under Test VRF Virtual Routing and Forwarding 4 Conformance requirement concerning PICS If it claims to conform to the present document, the actual

34、PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in ac

35、cordance with the instructions for completion given in clause A.1. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)7Annex A (normative): DS-LITE PICS Proforma Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may

36、 freely reproduce the DS-LITE PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed DS-LITE PICS. A.1 Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereb

37、y a supplier of an implementation of the requirements defined in ETSI TS 101 569-1 1 may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: - guidance for completing the PICS proforma; - ide

38、ntification of the implementation; - identification of the ETSI TS 101 569-1 1; - global statement of conformance; - PICS proforma tables. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines prese

39、nted in ISO/IEC 9646-7 3. Item column The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“.

40、Status column The following notations, defined in ISO/IEC 9646-7 3, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x proh

41、ibited (excluded) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined

42、 immediately following the table. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)8ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined

43、immediately following the table. i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ statuses above. Reference column The refer

44、ence column makes reference to ETSI TS 101 569-1 1 V1.1.1 (2013-10) except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 3, are used for the support column: Y or

45、 y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). NOTE 2: As stated in ISO/IEC 9646-7 3, support for a received PDU requires the ability to parse

46、all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range,

47、or the length of values allowed. The following notations are used: - range of values: example: 5 20 - list of values: , , ., example: 2, 4, 6, 8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size ( ) example: size

48、 (1 8) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column)

49、 within the PICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE: 5/1 is the reference to the answer of item 1 in table A.5 of annex A. ETSI ETSI TS 103 241-1 V1.1.1 (2015-01)9Prerequisite line A prerequisite line takes the form: Prerequi