ETSI TS 101 909-4-2006 Digital Broadband Cable Access to the Public Telecommunications Network IP Multimedia Time Critical Services Part 4 Network Call Signalling Protocol (V1 5 2 _1.pdf

《ETSI TS 101 909-4-2006 Digital Broadband Cable Access to the Public Telecommunications Network IP Multimedia Time Critical Services Part 4 Network Call Signalling Protocol (V1 5 2 _1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 909-4-2006 Digital Broadband Cable Access to the Public Telecommunications Network IP Multimedia Time Critical Services Part 4 Network Call Signalling Protocol (V1 5 2 _1.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 909-4 V1.5.2 (2006-08)Technical Specification Digital Broadband Cable Access to thePublic Telecommunications Network;IP Multimedia Time Critical Services;Part 4: Network Call Signalling ProtocolPartial Endorsement of ITU-T Recommendation J.162 (11/2005), modifiedETSI ETSI TS 101 909-4 V

2、1.5.2 (2006-08) 2 Reference RTS/AT-020048-04 Keywords access, broadband, cable, endorsement, IP, ISDN, multimedia, PSTN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucrati

3、f enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in

4、 contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the d

5、ocument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.et

6、si.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2006. All rights reserved. DECTTM, PLUGTESTST

7、M and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partn

8、ers. ETSI ETSI TS 101 909-4 V1.5.2 (2006-08) 3 Contents Intellectual Property Rights4 Foreword.4 Introduction 4 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .8 Endorsement notice 9 Global modifications to ITU-T Recommendation J.162 9 Annex ZA (informa

9、tive): Bibliography.26 History 28 ETSI ETSI TS 101 909-4 V1.5.2 (2006-08) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members

10、and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.o

11、rg/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essent

12、ial to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Access and Terminals (AT). The present document is part 4 of a multi-part deliverable covering Digital Broadband Cable Access to the Public Telecommunications Network; IP Multimedia

13、Time Critical Services. Full details of the entire series can be found in part 1. Introduction The cable industry in Europe and across other Global regions has already deployed broadband cable television Hybrid Fibre Coax (HFC) data networks running the Cable Modem Protocol. The cable industry is in

14、 the rapid stages of deploying IP Voice and other time critical multimedia services over these broadband cable television networks. The cable industry has recognized the urgent need to develop ETSI Technical Specifications aimed at developing interoperable interface specifications and mechanisms for

15、 the delivery of end-to-end advanced real time IP multimedia time critical services over bi-directional broadband cable networks. IPCablecom is a set of protocols and associated element functional requirements developed to deliver Quality of Service (QoS) enhanced secure IP multimedia time critical

16、communications services using packetized data transmission technology to a consumers home over the broadband cable television Hybrid Fibre/Coaxial (HFC) data network running the Cable Modem protocol. IPCablecom utilizes a network superstructure that overlays the two-way data-ready cable television n

17、etwork. While the initial service offerings in the IPCablecom product line are anticipated to be Packet Voice, the long-term project vision encompasses packet video and a large family of other packet-based services. The cable industry is a global market and therefore the ETSI standards are developed

18、 to align with standards either already developed or under development in other regions. The ETSI Specifications are consistent with the CableLabs/PacketCable set of specifications as published by the SCTE. An agreement has been established between ETSI and SCTE in the US to ensure, where appropriat

19、e, that the release of PacketCable and IPCablecom set of specifications are aligned and to avoid unnecessary duplication. The set of IPCablecom ETSI specifications also refers to ITU-SG9 draft and published recommendations relating to IP Cable Communication. The whole set of multi-part ETSI delivera

20、bles to which the present document belongs specify a Cable Communication Service for the delivery of IP Multimedia Time Critical Services over a HFC Broadband Cable Network to the consumers home cable telecom terminal. “IPCablecom“ also refers to the ETSI working group program that shall define and

21、develop these ETSI deliverables. Many cable television operators are upgrading their facilities to provide two way capability and using this capability to provide high speed IP data services per ITU-T Recommendations J.83 and J.112 1. These operators now want to expand the capability of this deliver

22、y platform to include a variety of time critical services. The present document is one of a series of documents required to achieve this goal. It provides a network based call signalling protocol necessary to establish connections. ETSI ETSI TS 101 909-4 V1.5.2 (2006-08) 5 The present document is pa

23、rt 4 of the series of ETSI deliverables and specifies a profile of an application programming interface, Media Gateway Controller Interface (MGCI), and a corresponding protocol, Media Gateway Control Protocol (MGCP), for controlling Voice over IP (VoIP) embedded clients from external call control el

24、ements. The MGCP assumes a call control architecture where the call control “intelligence“ is outside the media gateway and is handled by external call control elements. The profile, as described in the present document, will be referred to as the Network-based Call Signalling (NCS) Protocol. It is

25、based on the Media Gateway Control Protocol (MGCP) 1.0 RFC 3435, which is the result of a merging of the Simple Gateway Control Protocol, and the IP Device Control (IPDC) family of protocols, as well as additional ideas incorporated during the protocol development process. ETSI ETSI TS 101 909-4 V1.

26、5.2 (2006-08) 6 1 Scope The present document is a multi-part deliverable belonging to IPCablecom. The present part (part 4) specifies a profile of an application programming interface, Media Gateway Controller Interface (MGCI), and a corresponding protocol, Media Gateway Control Protocol (MGCP), for

27、 controlling Voice over IP (VoIP) embedded clients from external call control elements. The MGCP is based on a call control architecture, where the call control “intelligence“ resides outside the gateways and is handled by external call control elements. The profile, as described in the present docu

28、ment, is referred to as the Network Call Signalling (NCS) Protocol. Annex B of the present document specifies an expansion of the NCS protocol to emulate an Access Node of an ETSI compliant local exchange. This annex specifies the mapping of expansion of the NCS protocol to V5.2. Annex F of the pres

29、ent document specifies optional NCS components for the delivery of metering pulses. This multi-part deliverable specifies IPCablecom, a set of protocols and associated element functional requirements. These have been developed to deliver high Quality of Service (QoS), enhanced secure IP multimedia t

30、ime critical communication services to a consumers home over a cable television Hybrid Fibre/Coaxial (HFC) data network. NOTE 1: IPCablecom defines a set of documents in the framework of a network superstructure that overlays the two-way data-ready cable television network, e.g. as specified within

31、ES 201 488 5 and ES 200 800 3. While the initial service offerings in the IPCablecom product line are anticipated to be Packet Voice and Packet Video, the long-term project vision encompasses a large family of packet-based services. This may require in the future, not only careful maintenance contro

32、l but also an extension of the present set of documents. NOTE 2: The present set of documents aims for global acceptance and applicability. It is therefore developed in alignment with standards either already existing or under development in other regions and in International Telecommunications Unio

33、n (ITU). NOTE 3: There may also be relevant equivalent studies on-going in IETF or ITU specific to the needs of European IPCablecom. Where possible ETSI TC AT-D working group for IPCablecom should align annex B package annex or similar packages addressing the specific needs of European IPCablecom wi

34、th work on going in IETF, Cablelabs, or the ITU. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or

35、 non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ITU-T Recommendation J

36、.112: “Transmission systems for interactive cable television services“. 2 ETSI EN 300 324-1: “V interfaces at the digital Local Exchange (LE); V5.1 interface for the support of Access Network (AN); Part 1: V5.1 interface specification“. 3 ETSI ES 200 800: “Digital Video Broadcasting (DVB); DVB inter

37、action channel for Cable TV distribution systems (CATV)“. 4 ETSI ES 201 235 (series): “Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers “. 5 ETSI ES 201 488 (series): “Access and Terminals (AT); Data Over Cable Systems“. ETSI ETSI TS 101 909-4 V

38、1.5.2 (2006-08) 7 6 ETSI TS 101 909-3: “Access and Terminals (AT); Digital Broadband Cable Access to the Public Telecommunications Network; IP Multimedia Time Critical Services; Part 3: Audio Codec Requirements for the Provision of Bi-Directional Audio Service over Cable Television Networks using Ca

39、ble Modems“. 7 ETSI EN 300 659-1: “Access and Terminals (AT); Analogue access to the Public Switched Telephone Network (PSTN); Subscriber line protocol over the local loop for display (and related) services; Part 1: On-hook data transmission“. 8 ITU-T Recommendation J.162: “Network call signalling P

40、rotocol for the delivery of time-critical services over cable television networks using cable modems“. 9 ITU-T Recommendation G.711: “Pulse code modulation (PCM) of voice frequencies“. 10 ETSI ES 200 659-3: “Access and Terminals (AT); Analogue acces to the Public Switched Telephone Network (PSTN); S

41、ubscriber line protocol over the local loop for display (and related) services; Part 3: Data link message and parameter codings“. 11 ITU-T Recommendation V.25: “Automatic answering equipment and general procedures for automatic calling equipment on the general switched telephone network including pr

42、ocedures for disabling of echo control devices for both manually and automatically established calls“. 12 ETSI EN 300 347-1: “V interfaces at the digital Local Exchange (LE); V5.2 interface for the support of Access Network (AN); Part 1: V5.2 interface specification“. 13 ETSI EN 300 166: “Transmissi

43、on and Multiplexing (TM); Physical and electrical characteristics of hierarchical digital interfaces for equipment using the 2 048 kbit/s - based plesiochronous or synchronous digital hierarchies“. 14 ETSI EN 300 167: “Transmission and Multiplexing (TM); Functional characteristics of 2 048 kbit/s in

44、terfaces“. 15 ETSI TS 101 909-11: “Digital Broadband Cable Access to the Public Telecommunications Network; IP Multimedia Time Critical Services; Part 11: Security“. 16 IETF RFC 2833: “RTP Payload for DTMF Digits, Telephony Tones and Telephony Signals“. 17 ETSI ES 201 970 (see note): “Access and Ter

45、minals (AT); Public Switched Telephone Network (PSTN); Harmonized specification of physical and electrical characteristics at a 2-wire analogue presented Network Termination Point (NTP)“. 18 ETSI ES 202 971 (see note): “Access and Terminals (AT); Public Switched Telephone Network (PSTN); Harmonized

46、specification of physical and electrical characteristics of a 2-wire analogue interface for short line interface“. NOTE: EN 300 001 (declared historical at present) and EG 201 188 (an initial study detailed and updated in other documents later) were taken as base for the present document but they we

47、re later updated in ES 201 970 for the majority of the situations and in ES 202 971 for very short line interfaces, which is the most common case in IPCablecom systems. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply

48、: Access Node (AN): layer two termination device that terminates the network end of the ITU-T Recommendation J.112 1 connection NOTE: It is technology specific. In ITU-T Recommendation J.112 1, annex A, it is called the INA while in annex B it is the CMTS. ETSI ETSI TS 101 909-4 V1.5.2 (2006-08) 8 c

49、able modem: layer two termination device that terminates the customer end of the J.112 connection embedded multimedia terminal adapter: physical and logical interface but it is physically integrated with the HFC Cable Modem functionality NOTE: The difference in MTA and E-MTA defines product design architectures and is not relevant to this annex therefore these terms and their abbreviations are used synonymously and inter-changeably throughout the present document. internet protocol access node: device in which the PacketC