ETSI TS 100 573-2004 Digital cellular telecommunications system (Phase 2+) Physical Layer on the Radio Path (General Description)《数字蜂窝通信系统(第2+阶段) 无线通道上的物理层(一般描述)3GPP TS 05 01(版本8 9.pdf

《ETSI TS 100 573-2004 Digital cellular telecommunications system (Phase 2+) Physical Layer on the Radio Path (General Description)《数字蜂窝通信系统(第2+阶段) 无线通道上的物理层(一般描述)3GPP TS 05 01(版本8 9.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 100 573-2004 Digital cellular telecommunications system (Phase 2+) Physical Layer on the Radio Path (General Description)《数字蜂窝通信系统(第2+阶段) 无线通道上的物理层(一般描述)3GPP TS 05 01(版本8 9.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 100 573 V8.9.0 (2004-11)Technical Specification Digital cellular telecommunications system (Phase 2+);Physical Layer on the Radio Path (General Description)(3GPP TS 05.01 version 8.9.0 Release 1999)GLOBAL SYSTEM FOR MOBILE COMMUNICATIONSRETSI ETSI TS 100 573 V8.9.0 (2004-11) 1 3GPP TS 05.01

2、 version 8.9.0 Release 1999 Reference RTS/TSGG-010501v890 Keywords GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7

3、803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference ve

4、rsion is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of s

5、tatus. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notifi

6、cation No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered f

7、or the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 100 573 V8.9.0 (2004-11) 2 3GPP

8、 TS 05.01 version 8.9.0 Release 1999 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ET

9、SI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI

10、IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword T

11、his Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the correspon

12、ding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp . ETSI ETSI TS 100 573 V8.9.0 (2004-11) 3 3GPP TS 05.01 version 8.9.0 Release 1999 Contents Intellectual Property Rights2 Foreword.2 Foreword.4 1 Scope 5

13、 1.1 References 5 1.2 Abbreviations .6 2 Set of channels .6 3 Reference configuration .8 4 The block structures .9 5 Multiple access and timeslot structure .12 5.1 Hyperframes, superframes and multiframes.12 5.2 Time slots and bursts12 5.3 Channel organization15 6 Frequency hopping capability 16 7 C

14、oding and interleaving .18 7.1 General .18 7.2 Packet Traffic and Control Channels21 7.2.1 Channel coding for PDTCH21 7.2.1.1 Channel coding for GPRS PDTCH.21 7.2.1.2 Channel coding for EGPRS PDTCH 21 7.2.2 Channel coding for PACCH, PBCCH, PAGCH, PPCH, PNCH, CPBCCH, CPAGCH, CPPCH, CPNCH, and CSCH22

15、7.2.3 Channel Coding for the PRACH.22 8 Modulations23 9 Transmission and reception23 10 Other layer 1 functions.24 11 Performance .25 Annex A (informative): Reference configuration 26 Annex B (informative): Relations between specification 27 Annex C (informative): Change history .28 History 29 ETSI

16、ETSI TS 100 573 V8.9.0 (2004-11) 4 3GPP TS 05.01 version 8.9.0 Release 1999 Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG

17、approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval

18、; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI

19、TS 100 573 V8.9.0 (2004-11) 5 3GPP TS 05.01 version 8.9.0 Release 1999 1 Scope The present document is an introduction to the 05 series of the digital cellular telecommunications systems GSM technical specifications. It is not of a mandatory nature, but consists of a general description of the organ

20、ization of the physical layer with reference to the technical specifications where each part is specified in detail. It introduces furthermore, the reference configuration that will be used throughout this series of technical specifications. 1.1 References The following documents contain provisions

21、which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, t

22、he latest version applies. Non-specific eferences to 3GPP TSs and TRs imply the latest version pertaining to the same Release as the present document. 1 3GPP TS 01.04: “Digital cellular telecommunications system (Phase 2+); Abbreviations and acronyms“. 2 3GPP TS 03.03: “Digital cellular telecommunic

23、ations system (Phase 2+); Numbering, addressing and identification“. 3 3GPP TS 03.20: “Digital cellular telecommunications system (Phase 2+); Security related network functions“. 4 3GPP TS 03.22: “Digital cellular telecommunications system (Phase 2+); Functions related to Mobile Station (MS) in idle

24、 mode and group receive mode“. 5 3GPP TS 04.03: “Digital cellular telecommunications system (Phase 2+); Mobile Station - Base Station System (MS - BSS) interface; Channel structures and access capabilities“. 6 3GPP TS 04.08: “Digital cellular telecommunications system (Phase 2+); Mobile radio interf

25、ace layer 3 specification“. 7 3GPP TS 04.21: “Digital cellular telecommunications system (Phase 2+); Rate adaptation on the Mobile Station - Base Station System (MS-BSS) Interface“. 8 3GPP TS 05.02: “Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio

26、 path“. 9 3GPP TS 05.03: “Digital cellular telecommunications system (Phase 2+); Channel coding“. 10 3GPP TS 05.04: “Digital cellular telecommunications system (Phase 2+); Modulation“. 11 3GPP TS 05.05: “Digital cellular telecommunications system (Phase 2+); Radio transmission and reception“. 12 3GP

27、P TS 05.08: “Digital cellular telecommunications system (Phase 2+); Radio subsystem link control“. 13 3GPP TS 05.09: “Digital cellular telecommunications system (Phase 2+); Link adaptation“. 14 3GPP TS 05.10: “Digital cellular telecommunications system (Phase 2+); Radio subsystem synchronization“. 1

28、5 3GPP TS 03.30: “Digital cellular telecommunications system (Phase 2+); Radio network planning aspects“. ETSI ETSI TS 100 573 V8.9.0 (2004-11) 6 3GPP TS 05.01 version 8.9.0 Release 1999 16 3GPP TS 03.64: “Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Ov

29、erall description of the GPRS radio interface; Stage 2“. 17 3GPP TS 03.52: “Digital cellular telecommunications system (Phase 2+); GSM Cordless Telephony System (CTS); Phase 1; Lower layers of the CTS Radio Interface; Stage 2“. 18 3GPP TS 05.56: “Digital cellular telecommunications system (Phase 2+)

30、; GSM Cordless Telephony System (CTS); Phase 1; CTS-FP Radio subsystem“.TS 1.2 Abbreviations Abbreviations used in the present document are listed in 3GPP TR 01.04 1. 2 Set of channels The radio subsystem provides a certain number of logical channels that can be separated into two categories accordi

31、ng to 3GPP TS 04.03 5, 3GPP TS 03.64 15 and 3GPP TS 03.52 17: 1) The traffic channels (TCH): they are intended to carry two types of user information streams: encoded speech and data. The following types of traffic channels are defined: Bm or full-rate (TCH/F), Lm or half-rate (TCH/H), cell broadcas

32、t (CBCH), full rate packet data (PDTCH/F) and half rate packet data (PDTCH/H) traffic channels. For the purpose of this series of technical specifications, the following traffic channels are distinguished: - full rate speech TCH (TCH/FS); - enhanced full rate speech TCH (TCH/EFS) - half rate speech

33、TCH (TCH/HS); - adaptive full rate speech TCH (TCH/AFS); - adaptive half rate speech TCH (TCH/AHS); - 28,8 kbit/s full rate data E-TCH (E-TCH/F28.8); - 32,0 kbit/s full rate data E-TCH (E-TCH/F32.0); - 43,2 kbit/s full rate data E-TCH (E-TCH/F43.2); - 14,4 kbit/s full rate data TCH (TCH/F14.4); - 9,

34、6 kbit/s full rate data TCH (TCH/F9.6); - 4,8 kbit/s full rate data TCH (TCH/F4.8); - 4,8 kbit/s half rate data TCH (TCH/H4.8); - 2,4 kbit/s full rate data TCH (TCH/F2.4); - 2,4 kbit/s half rate data TCH (TCH/H2.4); - cell broadcast channel (CBCH); - full rate packet data traffic channel (PDTCH/F) ;

35、 - half rate packet data traffic channel (PDTCH/H). Adaptive speech traffic channels are channels for which part of the radio bandwidth is reserved for transmission of in band signalling to allow in call adaptation of the speech and channel codec. 8 full rate and 6 half rate block structures are def

36、ined for the adaptive traffic channels. All channels are bi-directional unless otherwise stated. Unidirectional downlink full rate channels, TCH/FD are defined as the downlink part of the corresponding TCH/F. Unidirectional uplink full rate channels are FFS. ETSI ETSI TS 100 573 V8.9.0 (2004-11) 7 3

37、GPP TS 05.01 version 8.9.0 Release 1999 The allocated uplink and downlink PDTCH are used independently of each other. Dependent allocation of uplink and downlink is possible. Multislot configurations for circuit switched connections are defined as multiple (1 up to 8) full rate channels allocated to

38、 the same MS. At least one channel shall be bi-directional (TCH/F). The multislot configuration is symmetric if all channels are bi-directional (TCH/F) and asymmetric if at least one channel is unidirectional (TCH/FD). High Speed Circuit Switched Data (HSCSD) is an example of multislot configuration

39、, in which all channels shall have the same channel mode. NOTE: For the maximum number of timeslots to be used for a HSCSD configuration, see 3GPP TS 03.34. Multislot configurations for packet switched connections are defined as multiple (1 up to 8) PDTCH/Us and one PACCH for one mobile originated c

40、ommunication, or multiple (1 up to 8) PDTCH/Ds and one PACCH for one mobile terminated communication respectively, allocated to the same MS. In this context allocation refers to the list of PDCH that may dynamically carry the PDTCHs for that specific MS. The PACCH shall be mapped onto one PDCH carry

41、ing one PDTCH/U or PDTCH/D. That PDCH shall be indicated in the resource allocation message (see 3GPP TS 04.60). Multislot configurations for dual transfer mode are defined as one bi-directional, traffic channel (TCH/H, TCH/F or E-TCH/F) and one packet channel combination. The packet channel combina

42、tion may consist of one PDTCH/U and one PACCH for one mobile originated communication, or multiple (1 or 2) PDTCH/Ds and one PACCH for one mobile terminated communication respectively, allocated to the same MS. The PACCH shall be mapped onto one PDCH carrying one PDTCH/U or PDTCH/D. That PDCH shall

43、be indicated in the resource allocation message (see 3GPP TS 04.60). An MS capable of dual transfer mode (DTM) shall support, as a minimum, DTM multislot class 5, which utilises the two-timeslot channelisation method, i.e. a single TCH/F plus a single PDTCH/F. In addition, the MS supporting DTM shal

44、l support TCH/H + PDCH/F configuration with the adaptive multirate (AMR) speech coder for voice coding. 2) The signalling channels: these can be sub-divided into (P)BCCH (packet) broadcast control channel), (P)CCCH (packet) common control channel), SDCCH (stand-alone dedicated control channel), (P)A

45、CCH (packet) associated control channel), packet timing advance control channel (PTCCH) and CTSCCH (CTS control channel). An associated control channel is always allocated in conjunction with, either a TCH, or an SDCCH. A packet associated control channel is always allocated in conjunction to one or

46、 multiple PDTCH, concurrently assigned to one MS. Two types of ACCH for circuit switched connections are defined: continuous stream (slow ACCH) and burst stealing mode (fast ACCH). For the purpose of this series of technical specifications, the following signalling channels are distinguished: - stan

47、d-alone dedicated control channel, four of them mapped on the same basic physical channel as the CCCH (SDCCH/4); - stand-alone dedicated control channel, eight of them mapped on a separate basic physical channel (SDCCH/8); - full rate fast associated control channel (FACCH/F); - enhanced circuit swi

48、tched full rate fast associated control channel (E-FACCH/F); - half rate fast associated control channel (FACCH/H); - slow, TCH/F or E-TCH/F associated, control channel (SACCH/TF); - slow, TCH/H associated, control channel (SACCH/TH); - slow, TCH/F or E-TCH/F associated, control channel for multislo

49、t configurations (SACCH/M); - slow, TCH/F associated, control channel for CTS (SACCH/CTS); - slow, SDCCH/4 associated, control channel (SACCH/C4); - slow, SDCCH/8 associated, control channel (SACCH/C8); - packet associated control channel (PACCH); ETSI ETSI TS 100 573 V8.9.0 (2004-11) 8 3GPP TS 05.01 version 8.9.0 Release 1999 - packet timing advance control channel (PTCCH); - broadcast control channel (BCCH); - packet broadcast control channel (PBCCH); - random access channel (i.e. uplink CCCH) (RACH); - packet random