ETSI GSM 11 10-1993 Mobile Station Conformity Specifications《移动台一致性规范》.pdf

《ETSI GSM 11 10-1993 Mobile Station Conformity Specifications《移动台一致性规范》.pdf》由会员分享，可在线阅读，更多相关《ETSI GSM 11 10-1993 Mobile Station Conformity Specifications《移动台一致性规范》.pdf（604页珍藏版）》请在麦多课文档分享上搜索。

1、ETSIITC SMG Date : June 1993 Released by : ETWPT48V UPDATE NOTE ETSI Technical Speciflcation GSM 11.10 Mobile Station conformity specifications Previously Released version : 3.7.0 (Release 92, Phase 1) Previously Updated version : 3.8.0 (April 1992) Previously Updated version : 3.9.0 (June 1992) Pre

2、viously Updated version : 3.1 0.0 (October 1992) Previously Updated version : 3.1 1 .O (January 1993) Previously Updated version : 3.12.0 (April 1993) New Updated version : 3.13.0 (June 1993) 1. Reason for Change Changes agreed at SMG#7 (Eindhoven) as listed in section 2 are included. 2. Details of

3、Change CR Sections Title of CR Ref Modified SMG Doc 11.10-374 11.8 Testing of SIM/ME interface section 11.8 - TMSI value 1 1. i 0-375 11.6 Cell Re-selection 11 .le377 11.8 Testing of the SIM/ME interfa- - section 11.8.9.2.1 -3, Mute Card 11 .10-378 11.8 Testing of the SIM/ME interface 11.10-379 11.4

4、 Nominal error rate and input level 11.10-383 11.5.3.7 Editorial Changes to the Signalling 11.10-384 11.5.3.5 Erroneous Error Handling Tests 1 1.10-385 11.5.3.6 Insufficient time allowed in test 11.10-386 1153.6 11.5.3.6.2.4 No change of page mode 11.10-388 11.3 Temporary Antenna Connector - Section

5、 11.8.7, Electrid TStS dynamic range 11.5.3.8 Tests II .4 Annex 1 11.10-390 11.4 Clarification of Mobile Station Terminology 41 3/93 41 2/93 412193 41 2/93 41 2/93 41 3/93 412193 412193 41 2/95 412193 41 3/93 UPDATE NOTE continued on page 2. - _ - = 3404583 0083953 240 UPDATENOTE - PAGE2 ta ETSI Tec

6、hnlcal Speclflcatlon GSM 11.10 CR Sections Title of CR I Modified Ref SMG Doc 11.10-391 11.6 Disabling of automatic network selection 11 JO-392 11.12 Brand and standardised MMI functions testing for Call Restriction Services 11.10-396 11.4 Consequential change due to CR 11.10-379 11.10-397 11.4 Cons

7、equential change due to CR 11.10-388 The following CR was approved by correspondence after SMG# 7 (30/06/93 to 16/07/93) 11.10-398 11.4 Consequential change due to CR 11.10-379 41 2/93 41 3/93 419193 501193 3. Instructlons to Ddate GSM 11.10 The version 3.12.0 of GSM 11.10 together with this update

8、consitutes version 3.13.0 of GSM 11.10. To facilitate substitution, complete sheets, if necessary with the reverse page from the previous version are provided. lhe new pages are marked in the header Updated June 1993 and as version 3.13.0. To delete I remove Old Page(s) Document Change Control recor

9、d Pl9 Front pihi I p9/10 11.3 p9/10 11.4 Pl-8 11.3 pl5116 II .4 pl 1-14 II 53.5 p 15-23 11.5.3.6 p5-18 11.5.3.7 p9/1 o 11.5.3.7 p 1 3-24 II 5.3.8 35136 11.6 p13-16 11.8 p3/4 11.8 pl 1/12 11.8 p29/30 11.12 p1/2 11.12 p 19-28 Annex 1 p3/4 Annex 2 p3/4 11.8 pl7118 No. of Sheets 1 1 1 1 1 4 2 5 2 2 6 1

10、2 1 1 1 1 1 5 1 1 New Page(s) To insert No. of Sheet Document Change Control recoid p 19/20 Front pi/ I p9/10 11.3 p9/10 11.4 Pl-8 11.4 pl 1-14 II .5.3.5 p15-21 11.5.3.6 p15-18 11.5.3.7 p9/1 o 11.5.3.7 p 1 3-24 11.5.3.8 psi36 11.6 p13-16 11.8 p314 11.8 pl1112 II .8 pl7118 11.8 p29/30 11.12 p1/2 Anne

11、 p3/4 Anne% , p3/4 11.3 pl5116 11.12 p 19-28 1 1 1 1 1 4 2 4 2 1 6 1 2 1 1 1 1 1 5 1 1 END OF UPDATE NOTE 3404583 OOL954 187 DOCUMENT CHANGE CONTROL RECORD - PAGE 19 to ETSI Technical Specification GSM 11.10 CR Sections Title of CR Modified Ref SMG Doc 11.10-344 11.8 Clarification of test conditions

12、 115/93 and nominal electrical values to be applied during the tests. 11.10-345 R1 11.10-346 11.10-347 11 . 10-348 11.8 11.8 11.8 11.8 Power Transition Phases 176/93 Characters of the Answer to Reset 114/93 Test Sequence 13: Secret Code Usage 115/93 New test procedure for test 115/93 sequence 11.8.1

13、0.1 11.10-349 11.10-350 11 . 10-355 II. 5.3.6 11.5.3.6.4.2, Assignment completion 115/93 III 111.1.4.5 Functionality of the DAI 114/9 11.4 11.6 Annex 1 Use of Temporary Antenna Connector 115/93 11.10-356 11.5.2 General sequence of frames in test 114/93 11.5.2.2.2.1 11.10-357 II . 5.3.5 Test 11.5.3.5

14、.6.1.2, Test of MS 115/93 reaction to unrecognised element in RR message on BCCH 11.10-358 11.10-359 R1 11.6 11.6 11.6, Cell Selection/Re-selection 115/93 Cell Selection/Re-selection test 161/93 I Updated version April 1993: 3.12.0 I The following CRs were approved at SMG No.6 (Reading) CR Sections

15、Title of CR Modified Ref SMG Doc 11 . 10-361 11.5.3.7 Testing of location update area 226/93 indication 11 . 10-362 11.4 Test Case 11.4.5 226/93 11.10-363 11.5.3.5 Missing Cause value 226/93 DOCUMENT CHANGE CONTROL RECORD continued on page 20. 3404583 0081955 013 = DOCUMENT CHANGE CONTROL RECORD - P

16、AGE 20 to ETSI Technical Specification GSM 11.10 CR Sections Title of CR Ref Modified SMG Doc 11.10-364 11.10-365 11.10-366 11.10-367 11.10-368 11.10-369 11.10-370 11.10-372 11.10-373 Ri 11.2 II. 17 II. 5.3.8 11.4 11.5.3.5 II. 5.3.6 11.8 11.9 II. 5.3.7 MS in Idle mode Reference to antenna coupling d

17、evice 11.5.3.8.2.6.1 and 11.5.3.8.2.7.1 are inconsistent Test Case 11.4.2.1 TI flag incorrect in 11.5.3.5.2.3 Classmark Change Erased Fields in 11.8.6 Incorrect references Manual Network Reselection 227/93 226/93 227/93 270/93 227/93 226/93 287/93 296/93 267/93R1 End of DOCUMENT CHANGE CONTROL RECOR

18、D. = 3404583 0083956 T5T EXSI/TC SMG Updated by : ETSI/pT12 Da te : June i993 Title : ETSI TECHNICAL SPECIFICATION GSM 11.10 MOBILE STATION CONFORMITY SPECIFICATIONS Version 3.13. O List of con tents : Aspect I : Aspect II : Aspect III : Annex 1 Annex 2 Annexij Annex Appendix A : Appendix B : Append

19、ix C : Detailed table of contents General Formai procedures and general requirements Network interfacing Individual equipment type requirements and interworking Reference test methods Measurement uncertainty Protocol implementation information The arrangement of the measuring equipment Guidance on t

20、he use of radiation test sites Guidance on the construction of an anechoic shielded chamber Test report Original language: English Number of pages : 502 (details on reverse page) GSM 11.10 D 3404583 008L957 996 D page ii V 3.13.0 June 1993 The parts of this version 3.13.0 of GSM 11-10 contain the fo

21、llowing number of pages : Part: front page index part I part 11.1 part 11.2 part I1.S II. part 11.5 (.O) part 11.5.1 part II. 5.2 part 11.5.3 (.O) part 11.5.3.1 part 11.5.3.2 part 11.5.3. part 11.5.3. part 11.5.3.5 part 11.5.3.6 part 11.5.3. part 11.5.3. part 11.5.3.9 part II. 6 part II. g part II.

22、10 part II. 11 part 11.12 part II. 1 part II. 1 part II. i5 part II. 16 part II. 17 part III annex 1 annex 2 appendix A appendix B appendix C 2 i part II. I1.g 2 annex 2 no. of pages: 2 12 14 10 6 16 23 1 1 3: 2 12 3 i 21 48 29 40 11 28 - (reserved) 34 1 1 2 12 1 26 12 z 1 4 3 in total 502 This numb

23、er does not include GSM 11.40 v.3.6.0 (46 pages). GSM 11.40 may be inserted after Annex 4. 3404583 008L958 822 W GSM 11.10 1.5 Number GSM 02.0 02.06 02.07 02.11 02.09 02.16 02.17 02. 02*20 o o3 1: 02.82 02.88 o3 o3 o3 o5 03.10 03.1 03.20 03.40 03.41 O3 4: 03.4 O3 45 03.46 O3 50 04 .o1 04.02 04.03 04

24、.04 04.05 04.06 04.07 04.08 04.10 04.11 04.12 04.21 04.22 04.80 04.82 04.88 Part I page 9 Updated June 1993 LIST OF THE GSM SPECIFICATIONS, ON WHICH THIS TEST SPECIFICATION IS BASED Version 3.2.0 3.4.0 3.7.1 3.2.0 3.4.1 3.1.0 3.7-0 3.0.1 3.2.0 3.2.0 3.6.1 3.6.1 305.0 3.390 3.0.2 3.0.2 3.3.2 3.5.0 3.

25、4.0 3.0.1 3.0.1 3.3.0 3.2.1 3.0.1 3.0.2 3.0.3 3.3.4 3.1.5 3.9-0 3.3.3 3.13.0 3.2.3 3.390 3.2.1 3.4.0 3.7.0 3.9-0 3.2.0 3.2.2 3.2.0 3.1.3 3.1.3 V 3.13.0 June 1993 Title Bearer Services Supported by a GSM PLMN Teleservices Supported by a GSM PLMN Description of Supplementary Services Types of Mobile S

26、tations Mobile Station Features Security Aspects Service Accessibility International MS Equipment Identities Subscriber Identity Modules, huictional Characteristics Man-machine Interface of the Mobile Station Procedures for Call Progress Indications Call Offering Supplementary Services Call Restrict

27、ion Supplementary Services Numbering, Addressing and Identification Technical performance objectives GSM PLMN Connection Types Discontinuous Reception (DRX) in the GSM System Support of DTMF via the GSM System Security-related Network Functions Technical Realization Short Message Service Point- to-p

28、oint Technical Realization of Short Message Service Cell Broadcast Technical Realization of Videotex Support of Teletex in a CSM PLMN Technical Realization of Facsimile Group 3 Service - transparent Technical Realization of Facsimile Group 3 Service - non transparent Transmission Planning Aspects of

29、 the Speech Service in the GSM PLMN System MS-BSS Interface - General Aspects and Principles GSM PLMN Access Reference Configuration MS-BSS Interface : Channel Structures and Access Capabilities MS-BSS Layer 1 - General Requirements MS-BSS Data Link Layer - General Aspects MS-Bss Data Link Layer Spe

30、cification Mobile Radio Interface Signalling Layer 3 - General Aspects Mobile Radio Interface - Layer 3 Specification Mobile Radio Interface Layer 3 - Supplementary Services Specification - General Aspects Point-to-point Short Message Service Support on Mobile Radio Interface Cell Broadcast Short Me

31、ssage Service Support on Mobile Radio Interface Rate Adaptation on MS-BSS Interface Radio Link Protocol for Data and Telematic Services on the Ms-BSS Interface Mobile Radio Interface Layer 3 - SS Specification - Formats and Coding Mobile Radio Interface Layer 3 - Call Offering SS Specification Mobil

32、e Radio Interface Layer 3 - Call Restriction - SS Specification 3404583 0081959 7b 9 GSM 11.10 05. o1 3.3.2 05.02 05.0 O5 * 02 05.0 05.02 05.10 06.01 06.10 06.11 3.6.1 3.5.1 3.1.2 3.15.0 3.7.0 3.5.1 3.0.0 3.2.0 3.0.1 06.12 3.0.1 06.31 3.1.0 06.32 3.0.0 07. o1 3.14.0 07.02 3.8.0 o7 .o3 3.4.0 09.02 11

33、.11 3.8.0 3.12.0 11.40 3.6.0 12.10 3.0.1 Part I page 10 Updated June 1993 V 3.13.0 June 1993 Physical La er on the Radio Path (General Descrip tion4 Multiplexing and Multiple Access on the Radio Path Channel Coding Modulation Radio Transmission and Reception Radio Subsystem Link Control Radio Subsys

34、tem Synchronization Speech Processing Functions : General Description GSM Full Rate Speech Transcoding Substitution and Muting of Lost Frames for Full- rate Speech Traffic Channels Comfort Noise Aspects for Full Rate Speech Traffic Channels Discontinuous Transmission (DTX) for hill Rate Speech Traff

35、ic Channels Voice Activity Detection General on Terminai Adaptation Functions for MSs Terminal Adaptation Functions for Services Using Asynchronous Bearer Capabilities Terminal Adaptation Functions for Services Using Synchronous Bearer Capabilities Mobile Application Part Specification Specification

36、 of the Internal Logical Organization of the SIM and its Interfaces System Simulator Specification (MS conformance test sys tem) Maintenance Provisions for Operational Integrity of MSS = 3404583 008L960 480 GSM 11.10 Part 11.3 page 9 v 3.12.0 Apr. 1993 11.3.3.2.2 Method of measurement for equipment

37、with an integral antenna Note: If the MS is equipped with a permanent connector, such that the antenna can be disconnected and the SS be connected directly, then the method of section 11.3.3.2.1 shall be applied. The tests in this section shall be performed on an unmodified test sample. The Ms shall

38、 be in the anechoic shielded chamber (Annex 1, GC5) or on the outdoor test site, on an isolated support, in the position for normal use. A test antenna, connected to the SS, shall be in the anechoic shielded chamber or on the test site, at a distance of at least 3 metres from the Ms. Note: The test

39、method described has been written for measurement in an anechoic shielded chamber. If an outdoor test site is used, then it is additionally necessary to raise/lower the test antenna through the specified height range to maximize the received power levels from both the test sample and the substitutio

40、n antenna. A call shall be originated by the SS to the MS and the MS shall be made to answer the call. The call shall be on an ARFCN, in the range 60 to 65, power control level set at MS maximum power, and timing advance O. Measure Peak Received Transmitter Carrier Power Using a sampling power measu

41、rement method with a sampling rate of at least 2/T, where T is bit duration, capture a representation of the MS transmit bursts amplitude and timing. From the array of samples the SS identifies the centre of the useful 147 transmitted bits, i.e. the transition from bit i3 to bit 14 of the midamble,

42、as the timing reference. This enables the peak received transmitter carrier power over the i47 useful bits to be calculated and used as the O dB reference. Match Power/Time Template The array of power samples shall be tested for a fit within the template of Figure 11.3.3. centred on the measured tra

43、nsition from bit i3 to bit 14 of the midamble of the measured burst. Measure Burst Timing The transition point identified in b) above is referred to the corresponding transition in the MS received burst. The SS shall then command the MS to each of the 16 power control levels (see Table 11.3.3) and s

44、teps b) to d) shall be repeated. The SS shall command the MS to the maximum power control level and steps b) to d) shall be repeated for ARFCN in the ranges 1 to 5, 30 to 35, 90 to 95 and 120 to 124. The SS shall cause the MS to generate an access burst on an ARFCN in the range 60 to 65. The SS shal

45、l capture this burst as described in b) above. However, in this case the SS needs to locate the centre of the useful bits of the burst by identifying the transition from the last bit of the sync sequence. timing reference, is then five data bits prior to this point. The centre of the template must b

46、e The centre of the burst, as the GSM 11.10 Part 11.3 page 10 Updated June 1993 Determine the peak received transmitter carrier power of the useful 87 bits of the burst, the 87 bits being symmetrically disposed about the centre point derived in g). This gives the O dB reference. The captured burst s

47、hall fit the template of Figure 11.3.4 with the centre of the template horizontal axis located on the centre located in g) above. Determine the time of the centre point derived in g) with respect to the MS received data on the common control channel. The SS shall modify the control data on the servi

48、ng cell BCCH in order to limit the transmit power on the Access Burst to power control level 10 (+Z3dBm). Steps g) to j) shall be repeated. The MS shall be rotated by n*45 degrees for all values of n in the range 1 to 7. At each rotation step b) shall be repeated for all channels of steps f) and a)

49、at the maximum power control level. The MS shall be replaced by a half-wave dipole, resonating at the centre frequency of the transmit band (902.5 MHz), connected to an RF generator. The output power of the RF generator shall be adjusted to reproduce the peak received transmitter owers recorded in steps e) (maximum power control level) , f) and lp delivered by the generator (in Watts) to the half-wave dipole, shall be recorded. These values shall be ordered in a matrix where the columns of the matrix represent the eight orientations of the MS and the rows of t