ETSI GSM 04 13-1994 European Digital Cellular Telecommunications System (Phase 2) Performance Requirements on the Mobile Radio Interface (ETS 300 561)《数字蜂窝通信系统(第2阶段) 移动无线接口的性能要求(ET_1.pdf

《ETSI GSM 04 13-1994 European Digital Cellular Telecommunications System (Phase 2) Performance Requirements on the Mobile Radio Interface (ETS 300 561)《数字蜂窝通信系统(第2阶段) 移动无线接口的性能要求(ET_1.pdf》由会员分享，可在线阅读，更多相关《ETSI GSM 04 13-1994 European Digital Cellular Telecommunications System (Phase 2) Performance Requirements on the Mobile Radio Interface (ETS 300 561)《数字蜂窝通信系统(第2阶段) 移动无线接口的性能要求(ET_1.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、= 3404583 OLL7007 128 s Released: IO May 1994 GSM 04.13 Version: 4.0.0 Date: 25 April 1994 Source: ETSI TC-SMG Reference: GSM 04. i 3 UDC: 621.396.21 Key words: European digital cellular telecommunications system, Global System for Mobile communications (GSM) European digital cellular telecommunicat

2、ions system (Phase 2); Performance Requirements on the Mobile Radio Interface (GSM 04.13) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: 06921 Sophia Antipolis Cedex - FRANCE Office address: Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE Tel.: + 33 9

3、2 94 42 O0 - Fax: + 33 93 65 47 16 European Telecommunications Standards Institute 1994. All rights reserved. No part may be reproduced except as authorised by written permission. The copyright and the foregoing restriction on reproduction extend to all media in which the information may be embodied

4、. . 1 Page 3 GSM 04.13 . version 4.0.0 : April 1994 Contents Foreword . 5 1 Scope . 7 2 Normative References . 7 3 Definitions and Abbreviations . 7 4 Default Condition., 8 5.3 5.4 5.5 5.6 5 Requirements . 8 5.1 General Requirements . 8 5.1.1 Response to Layer 3 Message 8 5.1.2 Response to an Errone

5、ous Layer 3 Message . 8 Layer 3 Radio Resource Signalling 8 5.2.1 Cell Reselection . 8 5.2.2 Paging Commands and Immediate Assignment Rejection (Timer T3122) 9 5.2.3 Immediate Assignment (Timer T31 O1 1 9 5.2.4 Channel Assignment . 9 5.2.5 Channel Mode Modify 9 5.2.6 Handover Access . 9 5.2.6.1 Fine

6、ly. pseudo and pre synchronized cases 9 5.2.6.2 Non synchronized case . 10 5.2.7 Encryption. . 11 5.2.8 Classmark Change 11 5.2.9 Classmark Interrogation . 11 5.2.1 O Release (Timer T31 1 O) . 11 Layer 3 Mobility Management Signallin 11 5.3.1 Periodic Location Updating timer 11 5.3.2 Identification

7、11 5.3.3 Authentication . 11 5.3.4 T3240 expiry . 11 5.3.5 TMSI reallocation . 12 5.3.6 IMSI detach 12 5.3.7 Location Updating with Random Access Failure . 12 5.3.8 Follow on call 12 Layer 3 Call Control Signallin . 12 5.4.1 Time to Send Setup Message 12 5.4.2 5.4.3 User Alerting . 13 5.4.4 Call Est

8、ablishment 13 5.4.5 Call Reestablishment 13 5.4.6 In Call Modification . 14 5.4.7 DTMF . 14 Supplementary Service Signallin . 14 5.5.1 Advice of Charge Charging 14 Short Message Services Point to Poin . 14 5.6.1 CP-DATA 14 5.6.2 RP-DATA 14 5.2 Response times to CC messages 13 Previous page is blank

9、Page 5 GSM 04.13 - version 4.0.0 : April 1994 = 3404583 OLL7009 TTO Foreword This space is reserved for the foreword of future versions of this document. Previous page is blank - ._ - Page 7 GSM 04.13 - version 4.0.0 : April 1994 = 3404583 0117010 712 W 1 Scope This Technical Specification specifies

10、 measurable performance requirements for signalling aspects of mobile stations. To allow implementation flexibility it has been chosen to specify requirements on the whole mobile station rather than to specify requirements on each OS1 layer. As a consequence the performance requirements do not fit c

11、onveniently in specifications such as TS GSM 04.08 (layer 3 only) or TS GSM 04.06 (layer 2 only). The main aim of this specification is to provide the justification for type approval testing of requirements that are not included in other GSM specifications. Where specific requirements are included i

12、n other GSM specifications they are not duplicated here. Mobile Stations have to perform a wide variety of functions. As a consequence most performance meesurements have to be made under a set of defined conditions: where necessary, these are included in this specification. Where necessary certain a

13、ssumptions are made about the interaction times between the mobile equipment and the SIM. If the (test) SIM does not respond within the assumed time then appropriate allowances shall be made. Additionally, it is intended that this specification should contain sufficient requirements to enable some u

14、ndefined network timers in TS GSM 04.08 to be calculated. 2 Normative References il 1 i21 i31 141 i51 i61 t71 GSM 01.04: “European digital cellular telecommunication system (Phase 2); Definitions, abbreviations and acronyms“. GSM 03.22: “European digital cellular telecommunication system (Phase 2);

15、Functions related to Mobile Station (MS) in idle mode“. GSM 04.06: “European digital cellular telecommunication system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface Data Link (DL) layer specification“. GSM 04.08: “European digital cellular telecommunication system (Phase 2); M

16、obile radio interface layer 3 specification“. GSM 04.86: “European digital cellular telecommunication system (Phase 2); Advice of Charge (AOC) supplementary services - Stage 3“. GSM 05.02: “European digital cellular telecommunication system (Phase 2); Multiplexing and multiple access on the radio pa

17、th“. GSM 05.08: “European digital cellular telecommunication system (Phase 2); Radio subsystem link control“, 3 Definitions and Abbreviations Abbreviations used in this specification are listed in GSM 01.04. Ready to transmit In this Technical Specification the phrase “ready to transmit the message

18、before time x“ is defined to mean that the MS shall transmit part of that message no later than the first burst of the first TCH or control channel block that occurs after time x. Previous page is blank 4 Default Conditions Unless otherwise stated, throughout this Technical Specification the followi

19、ng conditions are associated with the requirements : 5 5.1 ideal radio link with an insignificant bit error rate; no other signalling is in progress on the main DCCH; messages sent by the network are correctly formed; the only established data link (or the only data link to be established) is on SAP

20、I O; any Starting Time IE that is included in a message sent by the network does not require the action to be delayed; cells are not barred and all access classes are allowed; the layer 2 performance of the network shall satisfy the System Performance Requirements of section 5.9 of TS GSM 04.06; mes

21、sages sent by the network may contain any set of optional IEs, and any permitted set of conditional IEs: the mobile has a valid SIM inserted, is powered on, and the SIMS update status is updated; and on the BCCH, the Page Mode 1E is not set to paging reorganisation or same as before. Requirements Ge

22、neral Requirements 5.1.1 Response to Layer 3 Message The requirements of section 5.1.1 apply if there are no specific requirements for a layer 3 message in other parts of section 5. If the last timeslot of the message block containing a network command occurs at time T, then the MS shall be ready to

23、 transmit the response before time T+0.5s. 5.1.2 Response to an Erroneous Layer 3 Message If the last timeslot of the message block containing an erroneous RR, MM or CC message occurs at time T and if TS GSM 04.08 requires a status message to be returned to the network then the MS shall be ready to

24、transmit the RR-STATUS or MM-STATUS or STATUS message before T+0.5s. 5.2 Layer 3 Radio Resource Signalling 5.2.1 Cell Reselection If the BA(SACCH1 and BA(BCCH1 lists only differ by the carrier of the serving cell and if the MS has been in a call on the serving cell for more than 10 seconds then, if

25、the last timesiot of the message block containing a CHANNEL RELEASE message occurs at time T the MS shall respond to PAGE REQUEST messages sent later than T+ 3.5s. In other cases, if the last timeslot of the message block containing a CHANNEL RELEASE message occurs at time T the MS shall respond to

26、PAGE REQUEST messages sent later than T+R+2s, where R is the higher of 5s and (5*N+6) DIV 7) BS-PA-MFRMS / 4)s. N is the number of non- - - - - Page 9 GSM 04.13 - version 4.0.0 : April 1994 m 3404583 OL1701i2 595 m serving cell BCCH carriers in the BA(BCCH) list and the parameter BS-PA-MFRMS is defi

27、ned in TS GSM 05.02. 5.2.2 Paging Commands and Immediate Assignment Rejection (Timer T3122) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT REJECT message is sent at time T and contains a Wait Indication of W seconds then the MS shall at least respond to PAGE REQUEST mes

28、sages sent later than T + (W + 1 )s. Editors note : The time between a PAGE REQUEST message and any PAGE RESPONSE message is currently defined in TS GSM 04.08. After 04.13 has received approval, CRs will be drafted to move this requirement from TS GSM 04.08 to GSM 04.13. 5.2.3 Immediate Assignment (

29、Timer T31 O1 ) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT (or IMMEDIATE ASSIGNMENT EXTENDED) message is transmitted at time T then, the MS shall be ready to transmit the SABM frame with its information field before T+25ms. This requirement shall apply for assignment

30、 to TCH/F, TCH/H and SDCCH. 5.2.4 Channel Assignment If the last timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T, then the MS shall be ready to transmit the ASSIGNMENT COMPLETE message before T + 600ms. If the last timeslot of the message block containing an ASSIGNMEN

31、T COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the ASSIGNMENT FAILURE message on the old channel before T +2s. If the last timeslot o

32、f the message block containing an ASSIGNMENT COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS shall not attempt to establish a layer 2 link on the new channel, then the MS shall be ready to transmit any ASSIGNMENT FAILURE message on the old channel before T + 500ms. 5.2.5 Cha

33、nnel Mode Modify If the last timeslot of the message block containing a CHANNEL MODE MODIFY message occurs at time T, then the MS shall be ready to transmit the CHANNEL MODE MODIFY ACKNOWLEDGE message before T + 300ms. 5.2.6 Handover Access 5.2.6.1 Finely, pseudo and pre synchronized cases If the la

34、st timeslot of the message block containing a HANDOVER COMMAND message to a full rate TCH occurs at time T, then the MS shall be ready to transmit the HANDOVER COMPLETE message before T+650ms. If the last timeslot of the message block containing a HANDOVER COMMAND message to a half rate TCH occurs a

35、t time T, then the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 900ms. If the last timeslot of the message block containing a HANDOVER COMMAND message to an SDCCH occurs at time T, then the MS shall be ready to transmit the HANDOVER COMPLETE message before T+ 1.5s. Pa, .“ G

36、SM 04.13 - version 4.0.0 : April 1994 If the last timeslot of the message block containing a HANDOVER COMMAND to a full rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the

37、 MS shall be ready to transmit the HANDOVER FAILURE message on the old full rate TCH before T + 2s. If the last timeslot of the message block containing a HANDOVER COMMAND to a full rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on

38、 the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old SDCCH before T+2.5s. If the last timeslot of the message block containing a HANDOVER COMMAND to a half rate TCH occurs at time T and this HANDOVER COMMAND is such that

39、 the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old half rate TCH before T + 3s. If the last timeslot of the message block containing a HANDOVER COMMAND to a half ra

40、te TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old SDCCH before T + 3s. If the last timeslot of the me

41、ssage block containing a HANDOVER COMMAND to an SDCCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old SDCC

42、H before T+5s. If the last timeslot of the message block containing a HANDOVER COMMAND occurs at time T and this HANDOVER COMMAND is such that the MS shall not attempt to establish a layer 2 link on the new channel, then the MS shall be ready to transmit any HANDOVER FAILURE message on the old chann

43、el before T + 500ms. 5.2.6.2 Non synchronized case If the last timeslot of the message block containing the (one and only) PHYSICAL INFORMATION message occurs at time T, then on a full rate TCH the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 500ms. If the last timeslot of

44、the message block containing the (one and only) PHYSICAL INFORMATION message occurs at time T, then on a half rate TCH the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 750ms. If the last timeslot of the message block containing the (one and only) PHYSICAL INFORMATION messag

45、e occurs at time T, then on an SDCCH the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 1.5s. If the last timeslot of the message block containing a HANDOVER COMMAND to either a full rate or a half rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries

46、but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old TCH before T+ 1 .Is. If the last timeslot of the message block containing a HANDOVER COMMAND to an SDCCH occurs at time T and t

47、his HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old SDCCH before T + 2s. If the last timeslot of the message block containing a HAND

48、OVER COMMAND to either a full rate or a half rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old SDCC

49、H before T + 1.7s. If the last timeslot of the message block containing,a HANDOVER COMMAND occurs at time T and m 3404583 Oll17014 368 m Page 11 GSM 04.13 - version 4.0.0 : April 1994 this HANDOVER COMMAND is such that the MS shall not attempt to establish a layer 2 link on the new channel, then the MS shall be ready to transmit any HANDOVER FAILURE message on the old channel before T + 500ms. 5.2.7 Encryption If the last timeslot of the message block containing a CIPHERING MODE COMMAND message occurs at time T, then the MS shall be ready to transmit the C