ETSI EN 303 413-2017 Satellite Earth Stations and Systems (SES) Global Navigation Satellite System (GNSS) receivers Radio equipment operating in the 1 164 MHz to 1 300 MHz and 1 55.pdf

《ETSI EN 303 413-2017 Satellite Earth Stations and Systems (SES) Global Navigation Satellite System (GNSS) receivers Radio equipment operating in the 1 164 MHz to 1 300 MHz and 1 55.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 303 413-2017 Satellite Earth Stations and Systems (SES) Global Navigation Satellite System (GNSS) receivers Radio equipment operating in the 1 164 MHz to 1 300 MHz and 1 55.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 303 413 V1.1.1 (2017-06) Satellite Earth Stations and Systems (SES); Global Navigation Satellite System (GNSS) receivers; Radio equipment operating in the 1 164 MHz to 1 300 MHz and 1 559 MHz to 1 610 MHz frequency bands; Harmonised Standard covering the essential requirements of article 3.

2、2 of Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 303 413 V1.1.1 (2017-06) 2 Reference DEN/SES-00404 Keywords GNSS, harmonised standard, navigation, receiver, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 1

3、6 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in pri

4、nt. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the P

5、ortable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/po

6、rtal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electro

7、nic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All

8、rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its M

9、embers GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 303 413 V1.1.1 (2017-06) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Executive summary 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references

10、. 7g32.2 Informative references 7g33 Definitions and abbreviations . 9g33.1 Definitions 9g33.2 Abbreviations . 9g34 Technical requirements specifications . 10g34.1 Environmental profile . 10g34.2 Conformance specifications . 10g34.2.1 GUE adjacent frequency band selectivity performance 10g34.2.1.1 D

11、efinition 10g34.2.1.2 Specifications 10g34.2.1.3 Conformance . 11g34.2.2 Spurious emissions . 12g34.2.2.1 Definition 12g34.2.2.2 Limit 12g34.2.2.3 Conformance . 12g35 Testing for conformance with technical requirements . 12g35.1 Environmental conditions for testing . 12g35.2 Interpretation of the me

12、asurement results 13g35.3 Test methodology for adjacent frequency band selectivity test 13g35.3.1 General 13g35.3.2 Test setup for conducted measurements . 13g35.3.2.1 Test equipment 13g35.3.2.2 EUT configuration 13g35.3.3 Test setup for radiated measurements . 14g35.3.3.1 General 14g35.3.3.2 Test e

13、quipment 14g35.3.3.3 EUT configuration 14g35.4 GUE adjacent frequency band selectivity test 15g35.4.1 General 15g35.4.2 Test conditions 15g35.4.3 Test method for GUE utilizing the 1 559 MHz to 1 610 MHz RNSS band 15g35.4.4 Test method for GUE utilizing the 1 164 MHz to 1 300 MHz RNSS bands 16g35.5 R

14、eceiver spurious emissions test 16g35.5.1 Test conditions 16g35.5.2 Test method 16g35.5.2.1 Conducted measurement . 16g35.5.2.1.1 Introduction . 16g35.5.2.1.2 Pre-scan . 17g35.5.2.1.3 Measurement of the emissions identified during the pre-scan . 18g35.5.2.2 Radiated measurement 18g3Annex A (informat

15、ive): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 19g3ETSI ETSI EN 303 413 V1.1.1 (2017-06) 4 Annex B (normative): Details of parameters used in technical requirements specifications (clause 4) . 20g3B.1 Adjacent frequency signal 20g3B.1.1 Defin

16、ition . 20g3B.1.2 Recommended measurement technique for the adjacent frequency signal settings . 21g3B.2 GNSS signals 21g3B.2.1 Definition . 21g3B.2.2 GNSS signal details 21g3B.2.3 GNSS satellite details . 22g3Annex C (informative): C/N0degradation metric 23g3C.1 General . 23g3C.2 Definition . 23g3C

17、.3 Example calculation of nominal 1 dB degradation of C/N0. 23g3Annex D (informative): Test Report Application Form for ETSI EN 303 413 . 25g3D.1 The right to copy 25g3D.2 General . 25g3D.3 Information as required by clause 5.4.3 and clause 5.4.4 . 25g3D.4 Information as required by clause 5.5 27g3A

18、nnex E (informative): Bibliography . 28g3Annex F (informative): Change history . 29g3History 30g3ETSI ETSI EN 303 413 V1.1.1 (2017-06) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these es

19、sential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest upda

20、tes are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web serv

21、er) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commissions standardisation request C

22、(2015) 5376 final i.8 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present doc

23、ument is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requiremen

24、ts of that Directive and associated EFTA regulations. National transposition dates Date of adoption of this EN: 12 June 2017 Date of latest announcement of this EN (doa): 30 September 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 March 2018 Date of wi

25、thdrawal of any conflicting National Standard (dow): 31 March 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verb

26、al forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Executive summary The present document gives the technical requirements (clause 4) and test methodology (clause 5) for presumption of conformity of GNSS User Eq

27、uipment with article 3.2 of the Radio Equipment Directive (2014/53/EU) i.1. ETSI ETSI EN 303 413 V1.1.1 (2017-06) 6 Introduction ETSI has designed a modular structure for the standards. Each standard is a module in the structure. The modular structure is shown in ETSI EG 203 336 i.2. The present doc

28、ument defines technical requirements to support the essential requirements of article 3.2 of the Radio Equipment Directive i.1 which states “Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“.

29、 The present document does not contain any requirement, recommendation, or information about the installation of the GNSS user equipment. ETSI ETSI EN 303 413 V1.1.1 (2017-06) 7 1 Scope The present document specifies technical characteristics and methods of measurements for Global Navigation Satelli

30、te System (GNSS) User Equipment (GUE). Global Navigation Satellite System (GNSS) User Equipment (GUE) is capable of operating as part of one or more radionavigation-satellite service (RNSS) systems in the RNSS frequency bands given in table 1-1. Table 1-1: Radionavigation-satellite service (RNSS) fr

31、equency bands RNSS frequency bands Comments 1 164 MHz to 1 300 MHz space-to-Earth 1 559 MHz to 1 610 MHz space-to-Earth A GUE receives radio signals from one or more GNSS for the purpose of radiodetermination of the position, velocity, and/or other characteristics of an object, or the obtaining of i

32、nformation relating to those parameters, by means of the propagation properties of radio waves. RNSS is defined as “A radiodetermination-satellite service used for the purpose of radionavigation“ (article 1.43 of ITU Radio Regulations i.13). The present document applies to all GUE operating in the b

33、ands given in table 1-1 with the ability to receive any GNSS (e.g. Galileo, Global Positioning System (GPS), BeiDou (BDS), Global Navigation Satellite System (GLONASS), Space Based Augmentation Systems (SBAS). The present document covers the essential requirements of article 3.2 of Directive 2014/53

34、/EU i.1 under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expec

35、ted location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1

36、ETSI EN 300 328 (V2.1.1) (11-2016): “Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU“. 2.2 Informative references Inf

37、ormative references are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies.

38、 NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. ETSI ETSI EN 303 413 V1.1.1 (2017-06) 8 The following referenced documents are not necessary for the application of the present document but they assist the user

39、 with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI EG 20

40、3 336 (V1.1.1) (08-2015): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.3 Recommendation ITU-R M.1787: “Description of sys

41、tems and networks in the radionavigation-satellite service (space-to-Earth and space-to-space) and technical characteristics of transmitting space stations operating in the bands 1 164-1 215 MHz, 1 215-1 300 MHz and 1 559-1 610 MHz“. i.4 Recommendation ITU-R M.1901: “Guidance on ITU-R Recommendation

42、s related to systems and networks in the radionavigation-satellite service operating in the frequency bands 1 164-1 215 MHz, 1 215-1 300 MHz, 1 559-1 610 MHz, 5 000-5 010 MHz and 5 010-5 030 MHz“. i.5 Recommendation ITU-R M.1902: “Characteristics and protection criteria for receiving earth stations

43、in the radionavigation-satellite service (space-to-Earth) operating in the band 1 215-1 300 MHz“. i.6 Recommendation ITU-R M.1903: “Characteristics and protection criteria for receiving earth stations in the radionavigation-satellite service (space-to-Earth) and receivers in the aeronautical radiona

44、vigation service operating in the band 1 559-1 610 MHz“. i.7 Recommendation ITU-R M.1905: “Characteristics and protection criteria for receiving earth stations in the radionavigation-satellite service (space-to-Earth) operating in the band 1 164-1 215 MHz“. i.8 Commission Implementing Decision C(201

45、5) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.9 CISPR 16-1

46、-4 Ed.3.0 (2010): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements“. i.10 ETSI TR 102 273 all parts: “Electromagnetic compatibility and Radi

47、o spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties“. i.11 ETSI TR 100 028-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipme

48、nt characteristics; Part 1“. i.12 ETSI TR 100 028-2: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. i.13 ITU Radio Regulations (edition of 2016). ETSI ETSI EN 303 413 V1.1.1 (2017-06) 9 3 Definitio

49、ns and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU i.1 and the following apply: C/N0: carrier to noise-density ratio, expressed in dB-Hz NOTE: The ratio of the received (GNSS) signal carrier power C, in dBW or dBm, to the noise power spectral density, in dBW/Hz or dBm/Hz, in the absence of interference. C/(N0+I): carrier to noise-and-interference-density ratio,C/(N0+I), in dB-Hz conducted measurements: measurements of the performance of the EUT mad