ETSI EN 301 908-2-2015 IMT cellular networks Harmonised EN covering the essential requirements of article 3 2 of the R&TTE Directive Part 2 CDMA Direct Spread (UTRA FDD) User Equip.pdf

《ETSI EN 301 908-2-2015 IMT cellular networks Harmonised EN covering the essential requirements of article 3 2 of the R&TTE Directive Part 2 CDMA Direct Spread (UTRA FDD) User Equip.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 908-2-2015 IMT cellular networks Harmonised EN covering the essential requirements of article 3 2 of the R&TTE Directive Part 2 CDMA Direct Spread (UTRA FDD) User Equip.pdf（53页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 908-2 V7.1.1 (2015-12) IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 2 Reference REN/MSG-TFES-011-02 Keywords

2、 3G, 3GPP, cellular, digital, IMT, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse

3、 (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified witho

4、ut the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of th

5、e present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to o

6、ne of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The conte

7、nt of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Ma

8、rks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 3

9、 Contents Intellectual Property Rights 7g3Foreword . 7g3Modal verbs terminology 7g3Introduction 7g31 Scope 8g32 References 9g32.1 Normative references . 9g32.2 Informative references 9g33 Definitions, symbols and abbreviations . 10g33.1 Definitions 10g33.2 Symbols 11g33.3 Abbreviations . 12g34 Techn

10、ical requirements specifications . 13g34.1 Environmental profile . 13g34.2 Conformance requirements 13g34.2.1 Introduction. 13g34.2.2 Transmitter maximum output power. 14g34.2.2.1 Transmitter maximum output power . 14g34.2.2.1.1 Definition. 14g34.2.2.1.2 Limits 14g34.2.2.1.3 Conformance . 14g34.2.2.

11、2 Transmitter maximum output power for DC-HSUPA 14g34.2.2.2.1 Definition for DC-HSUPA 14g34.2.2.2.2 Limits for DC-HSUPA 15g34.2.2.2.3 Conformance . 15g34.2.2.3 Transmitter maximum output power for UL OLTD . 15g34.2.2.3.1 Definition for UL OLTD . 15g34.2.2.3.2 Limits for UL OLTD . 15g34.2.2.3.3 Confo

12、rmance . 15g34.2.3 Transmitter spectrum emission mask 16g34.2.3.1 Transmitter spectrum emission mask 16g34.2.3.1.1 Definition. 16g34.2.3.1.2 Limits 16g34.2.3.1.3 Conformance . 16g34.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 16g34.2.3.2.1 Definition for DC-HSUPA 16g34.2.3.2.2 Limits for

13、 DC-HSUPA 16g34.2.3.2.3 Conformance . 17g34.2.3.3 Transmitter spectrum emission mask for UL OLTD 17g34.2.3.3.1 Definition for UL OLTD . 17g34.2.3.3.2 Limits for UL OLTD . 17g34.2.3.3.3 Conformance . 17g34.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 18g34.2.3.4.1 Definitio

14、n for UL CLTD Activation state 1 18g34.2.3.4.2 Limits for UL CLTD Activation state 1 18g34.2.3.4.3 Conformance . 18g34.2.4 Transmitter spurious emissions . 18g34.2.4.1 Transmitter spurious emissions . 18g34.2.4.1.1 Definition. 18g34.2.4.1.2 Limits 18g34.2.4.1.3 Conformance . 20g34.2.4.2 Transmitter

15、spurious emissions for DC-HSUPA 20g34.2.4.2.1 Definition for DC-HSUPA 20g34.2.4.2.2 Limits for DC-HSUPA 20g3ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 4 4.2.4.2.3 Conformance . 22g34.2.5 Transmitter minimum output power . 23g34.2.5.1 Transmitter minimum output power 23g34.2.5.1.1 Definition. 23g34.2.5.

16、1.2 Limits 23g34.2.5.1.3 Conformance . 23g34.2.5.2 Transmitter minimum output power for DC-HSUPA . 23g34.2.5.2.1 Definition for DC-HSUPA 23g34.2.5.2.2 Limits for DC-HSUPA 23g34.2.5.2.3 Conformance . 23g34.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 23g34.2.5.3.1 Definitio

17、n for UL CLTD Activation state 1 23g34.2.5.3.2 Limits for UL CLTD Activation state 1 23g34.2.5.3.3 Conformance . 23g34.2.6 Receiver Adjacent Channel Selectivity (ACS) . 23g34.2.6.1 Definition 23g34.2.6.2 Limits 24g34.2.6.3 Conformance . 24g34.2.7 Receiver blocking characteristics . 24g34.2.7.1 Defin

18、ition 24g34.2.7.2 Limits 24g34.2.7.3 Conformance . 26g34.2.8 Receiver spurious response . 26g34.2.8.1 Definition 26g34.2.8.2 Limits 26g34.2.8.3 Conformance . 26g34.2.9 Receiver intermodulation characteristics 26g34.2.9.1 Definition 26g34.2.9.2 Limits 26g34.2.9.3 Conformance . 27g34.2.10 Receiver spu

19、rious emissions . 27g34.2.10.1 Definition 27g34.2.10.2 Limits 27g34.2.10.3 Conformance . 28g34.2.11 Out-of-synchronization handling of output power 28g34.2.11.1 Definition 28g34.2.11.2 Limits 28g34.2.11.3 Conformance . 30g34.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 30g34.2.12.1

20、 Transmitter adjacent channel leakage power ratio (ACLR) 30g34.2.12.1.1 Definition. 30g34.2.12.1.2 Limits 30g34.2.12.1.3 Conformance . 30g34.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA 30g34.2.12.2.1 Definition for DC-HSUPA 30g34.2.12.2.2 Limits for DC-HSUPA 30g34.2.12.2.3 Conformance .

21、 30g34.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 31g34.2.12.3.1 Definition for UL OLTD . 31g34.2.12.3.2 Limits for UL OLTD . 31g34.2.12.3.3 Conformance . 31g34.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 31g34.2.12.4.1 Definition for UL CLTD Activation

22、state 1 31g34.2.12.4.2 Limits for UL CLTD Activation state 1 31g34.2.12.4.3 Conformance . 31g35 Testing for compliance with technical requirements 32g35.1 Environmental conditions for testing . 32g35.2 Interpretation of the measurement results 32g35.3 Essential radio test suites 33g35.3.1 Transmitte

23、r maximum output power. 33g35.3.1.1 Method of test . 33g3ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 5 5.3.1.1.1 UTRA 33g35.3.1.1.1A DC-HSUPA . 34g35.3.1.1.1B UL OLTD 34g35.3.1.2 Test requirements 35g35.3.2 Transmitter spectrum emission mask 35g35.3.2.1 Method of test . 35g35.3.2.1.1 UEs not supporting

24、HSDPA and/or E-DCH 35g35.3.2.1.1A UEs supporting HSDPA and/or E-DCH 36g35.3.2.1.1B DC-HSUPA . 36g35.3.2.1.1C UL OLTD 36g35.3.2.1.1D UL CLTD Activation state 1 . 37g35.3.2.2 Test requirements 38g35.3.3 Transmitter spurious emissions . 38g35.3.3.1 Method of test . 38g35.3.3.1.1 UTRA 38g35.3.3.1.1A DC-

25、HSUPA . 38g35.3.3.2 Test requirements 39g35.3.4 Transmitter minimum output power . 39g35.3.4.1 Method of test . 39g35.3.4.1.1 UTRA 39g35.3.4.1.1A DC-HSUPA . 39g35.3.4.1.1B UL CLTD Activation state 1 . 40g35.3.4.2 Test requirements 40g35.3.5 Receiver Adjacent Channel Selectivity (ACS) . 40g35.3.5.1 M

26、ethod of test . 40g35.3.5.1.1 Initial conditions 40g35.3.5.1.2 Procedure . 41g35.3.5.2 Test requirements 41g35.3.6 Receiver blocking characteristics . 41g35.3.6.1 Method of test . 41g35.3.6.1.1 Initial requirements 41g35.3.6.1.2 Procedure . 41g35.3.6.2 Test requirements 41g35.3.7 Receiver spurious r

27、esponse . 42g35.3.7.1 Method of test . 42g35.3.7.1.1 Initial conditions 42g35.3.7.1.2 Procedure . 42g35.3.7.2 Test requirements 42g35.3.8 Receiver Intermodulation characteristics 42g35.3.8.1 Method of test . 42g35.3.8.1.1 Initial conditions 42g35.3.8.1.2 Procedure . 43g35.3.8.2 Test requirements 43g

28、35.3.9 Receiver spurious emissions . 43g35.3.9.1 Method of test . 43g35.3.9.1.1 Initial conditions 43g35.3.9.1.2 Procedure . 43g35.3.9.2 Test requirements 43g35.3.10 Out-of-synchronization handling of output power 43g35.3.10.1 Method of test . 43g35.3.10.1.1 Initial conditions 43g35.3.10.1.2 Procedu

29、re . 44g35.3.10.2 Test requirements 44g35.3.11 Transmitter adjacent channel leakage power ratio 44g35.3.11.1 Method of test . 44g35.3.11.1.1 UEs not supporting HSDPA and/or E-DCH 44g35.3.11.1.1A UEs supporting HSDPA and/or E-DCH 45g35.3.11.1.1B DC-HSUPA . 45g35.3.11.1.1C UL OLTD 45g35.3.11.1.1D UL C

30、LTD Activation state 1 . 46g35.3.11.2 Test requirements 47g3ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 6 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) 48g3Annex B (normative): Environmental profile . 50g3B.1 General . 50g3B.1.1 Introduction 50g3B.1.2 Temperatur

31、e . 50g3B.1.3 Voltage . 50g3B.1.4 Test environment 50g3Annex C: Void 51g3Annex D (informative): Bibliography . 52g3History 53g3ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The in

32、formation pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from t

33、he ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or th

34、e updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandates

35、 M/284 and M/406 issued from the European Commission under Directive 98/34/EC i.1 as amended by Directive 98/48/EC i.10. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonised

36、 Standard under the Directive 1999/5/EC i.2. The requirements relevant to Directive 1999/5/EC i.2 are summarized in annex A. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.11. National transposition dates Date of adoption of thi

37、s EN: 21 December 2015 Date of latest announcement of this EN (doa): 31 March 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2016 Date of withdrawal of any conflicting National Standard (dow): 30 September 2017 Modal verbs terminology In the

38、present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI delivera

39、bles except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R - for user equipment designed to be fixed o

40、r installed, the present document does not address the requirements described in Commission Decision 2010/267/EU i.7, ECC Decision (09)03 i.8 and CEPT Report 30 i.9. The present document is intended to cover the provisions of Directive 1999/5/EC i.2 (R User Equipment (UE) conformance specification;

41、Radio transmission and reception (FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 12.1.0 Release 12)“. 3 ETSI TS 134 108 (V12.1.0) (10-2015): “Universal Mobile Telecommunications System (UMTS); LTE; Common test environments for User Equipment (UE); Conformance testing (3GPP TS 34.1

42、08 version 12.1.0 Release 12)“. 4 ETSI TS 134 109 (V12.0.0) (09-2014): “Universal Mobile Telecommunications System (UMTS); Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109 version 12.0.0 Release 12)“. 5 ETSI TS 125 101 (V11.11.0) (01-2015): “Universal Mobile Tel

43、ecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0 Release 11)“. 6 IEC 60068-2-1 (03-2007): “Environmental testing - Part 2-1: Tests - Test A: Cold“. 7 IEC 60068-2-2 (07-2007): “Environmental testing - Part 2-2: Tests - Test B: D

44、ry heat“. 8 ETSI TS 125 214 (V11.12.0) (07-2015): “Universal Mobile Telecommunications System (UMTS); Physical layer procedures (FDD) (3GPP TS 25.214 version 11.12.0 Release 11)“. 9 ETSI TS 145 004 (V11.0.0) (10-2012): “Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.00

45、4 version 11.0.0 Release 11)“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the refere

46、nce document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist t

47、he user with regard to a particular subject area. i.1 Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. i.2 Directive 1999/5/EC of the European Parliament and

48、of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R A guide to the production of Harmonized Standards for application under the R Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in

49、 the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz“. i.5 Void. i.6 ETSI TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. i.7 Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in the 790-862 MHz frequency band for terrestrial systems capable of providing electronic communications services in the E