ETSI EN 301 908-12-2016 IMT cellular networks Harmonised Standard covering the essential requirements of article 3 2 of the Directive 2014 53 EU Part 12 CDMA Multi-Carrier (cdma200_1.pdf

《ETSI EN 301 908-12-2016 IMT cellular networks Harmonised Standard covering the essential requirements of article 3 2 of the Directive 2014 53 EU Part 12 CDMA Multi-Carrier (cdma200_1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 908-12-2016 IMT cellular networks Harmonised Standard covering the essential requirements of article 3 2 of the Directive 2014 53 EU Part 12 CDMA Multi-Carrier (cdma200_1.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 908-12 V7.1.1 (2016-05) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 12: CDMA Multi-Carrier (cdma2000) Repeaters HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-12 V7.1.1 (2016-05)2 Reference REN/MSG-TF

2、ES-11-12-RED Keywords 3G, 3GPP2, cdma2000, digital, IMT-2000, regulation, repeater, testing, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-P

3、rfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not

4、 be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secret

5、ariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, p

6、lease send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written p

7、ermission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMan

8、d the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN

9、301 908-12 V7.1.1 (2016-05)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 9g33.3 Ab

10、breviations . 9g34 Technical requirements specifications . 10g34.1 Environmental profile . 10g34.2 Conformance requirements 10g34.2.1 Introduction. 10g34.2.2 Spectrum emissions mask . 11g34.2.2.1 Definition 11g34.2.2.2 Limits 11g34.2.2.3 Conformance . 11g34.2.3 Spurious emissions . 12g34.2.3.1 Defin

11、ition 12g34.2.3.2 Limits 12g34.2.3.2.1 Spurious emissions 12g34.2.3.3 Conformance . 14g34.2.4 Maximum output power 14g34.2.4.1 Definition 14g34.2.4.2 Limits 14g34.2.4.3 Conformance . 14g34.2.5 Input intermodulation . 14g34.2.5.1 Definition 14g34.2.5.2 Limits 15g34.2.5.3 Conformance . 15g34.2.6 Out-o

12、f-band gain . 15g34.2.6.1 Definition 15g34.2.6.2 Limits 15g34.2.6.3 Conformance . 16g34.2.7 Output intermodulation . 16g34.2.7.1 Definition 16g34.2.7.2 Limits 16g34.2.7.3 Conformance . 16g35 Testing for compliance with technical requirements 17g35.1 Conditions for testing . 17g35.1.1 Introduction. 1

13、7g35.1.2 Standard equipment under test 17g35.2 Interpretation of the measurement results 17g35.3 Essential radio test suites 17g35.3.1 Spectrum emission mask 17g35.3.1.1 Initial conditions . 17g35.3.1.2 Procedures . 18g35.3.1.3 Test requirement . 18g35.3.2 Spurious emissions . 18g35.3.2.1 Initial co

14、nditions . 18g35.3.2.2 Procedure 18g3ETSI ETSI EN 301 908-12 V7.1.1 (2016-05)4 5.3.2.3 Test requirement . 18g35.3.3 Maximum output power 18g35.3.3.1 Initial conditions . 18g35.3.3.2 Procedure 18g35.3.3.3 Test requirement . 19g35.3.4 Input intermodulation . 19g35.3.4.1 Initial conditions . 19g35.3.4.

15、2 Procedures . 19g35.3.4.3 Test requirement . 20g35.3.5 Out-of-band gain . 20g35.3.5.1 Initial conditions . 20g35.3.5.2 Procedure 20g35.3.5.3 Test requirement . 21g35.3.6 Output intermodulation . 21g35.3.6.1 Initial conditions . 21g35.3.6.2 Procedure 21g35.3.6.3 Test requirement . 21g3Annex A (norma

16、tive): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 22g3Annex B (normative): Repeater configurations 23g3B.1 Power supply 23g3B.2 Power supply options . 23g3B.3 Ancillary equipment . 23g3Annex C (informative): Environmental profile specification

17、. 24g3Annex D (informative): Bibliography . 25g3History 26g3ETSI ETSI EN 301 908-12 V7.1.1 (2016-05)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly a

18、vailable for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web s

19、erver (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may be

20、come, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document has been prepared u

21、nder the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing

22、 Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformi

23、ty with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 12 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.3. National transposition dates Date of adoption of this EN: 20 April 2016 Date

24、 of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 2017 Date of withdrawal of any conflicting National Standard (dow): 31 January 2018 Modal verbs terminology In the present document “shall“, “shall

25、 not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct

26、citation. Introduction The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover radio equipment within the scope of the Radio Equipment Directive i.1. The present document is produced following the guidance in ETSI EG 203 336 i.2 a

27、s applicable. ETSI ETSI EN 301 908-12 V7.1.1 (2016-05)6 1 Scope The present document applies to the following equipment types: 1) Repeaters for IMT-2000 CDMA multi-carrier (cdma2000) This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table

28、 1-1: CDMA multi-carrier Repeater operating bands Band Class (BC) Direction of transmission CDMA multi-carrier Repeater operating bands 6 Forward link (DL) 2 110 MHz to 2 170 MHz Reverse link (UL) 1 920 MHz to 1 980 MHz 8 Forward link (DL) 1 805 MHz to 1 880 MHz Reverse link (UL) 1 710 MHz to 1 785

29、MHz 9 Forward link (DL) 925 MHz to 960 MHz Reverse link (UL) 880 MHz to 915 MHz 13 Forward link (DL) 2 620 MHz to 2 690 MHz Reverse link (UL) 2 500 MHz to 2 570 MHz Repeaters for IMT-2000 CDMA multi-carrier (cdma2000) may support: 1) operation in cdma2000 spread spectrum systems as defined in 3GPP2

30、C.S0002-F i.5, referred to herein as operation in Type 1 cdma2000 systems; or 2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 i.6, referred to herein in Type 2 cdma2000 systems. The present document contains requirements to demonstrate that Radio equipment both effective

31、ly uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited v

32、ersion applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks incl

33、uded in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 TIA-1037-A (May 2012): “Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Re

34、peaters“. 2 TIA-1030-F (September 2015): “Band Class Specification for cdma2000 Spread Spectrum Systems“. 3 3GPP2 C.S0032-D (March 2014): “Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Network“. NOTE: Available at http:/www.3gpp2.org/Public_html/specs/C.S0032-D_

35、v2.0_20140321.pdf. ETSI ETSI EN 301 908-12 V7.1.1 (2016-05)7 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, th

36、e latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the pr

37、esent document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repeal

38、ing Directive 1999/5/EC. i.2 ETSI EG 203 336 (V1.1.1) (06-2015): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.3 ETSI EN 3

39、01 908-1 (V11.1.1): “IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements“. i.4 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the Europ

40、ean Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.5 3GPP2 C.S0002-F V2.0 (05-2014): “Physical Layer Standard for cdma2000 Spread

41、Spectrum Systems Revision F“. NOTE: Available at http:/www.3gpp2.org/Public_html/specs/C.S0002-F%20v2.0_20140519.pdf. i.6 TIA-856-B-2 (July 2012): “cdma2000 High Rate Packet Data Air Interface Specification“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present do

42、cument, the following terms and definitions apply: Band Class (BC): set of frequency channels and a numbering scheme for these channels Base Station (BS): fixed station used for communicating with mobile stations NOTE: Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support, operation i

43、n cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-F i.5, referred to herein as operation in Type 1 cdma2000 system, or operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 i.6, referred to herein as operation in Type 2 cdma2000 systems. Depending upon the context, t

44、he term Base Station may refer to a cell, a sector within a cell, an MSC, and access network or other part of the wireless system. See also MSC. CDMA channel: set of channels transmitted from the Base Station and the mobile stations on a given frequency CDMA channel number: 11-bit number correspondi

45、ng to the centre of the CDMA frequency assignment CDMA frequency assignment: 1,23 MHz segment of spectrum NOTE: For band classes 6, 8 and 9, the channel is centred on one of the 50 kHz channels. chip rate: rate of “chips“ (modulated symbols after spreading) per second ETSI ETSI EN 301 908-12 V7.1.1

46、(2016-05)8 Code Division Multiple Access (CDMA): technique for spread-spectrum multiple-access digital communications that creates channels through the use of unique code sequences donor coupling loss: coupling loss between the Repeater and the donor Base Station DownLink (DL): signal path where Bas

47、e Station or Repeater transmits and the mobile receives NOTE: Also referred to as the forward link. environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the present document forward CDMA c

48、hannel: CDMA channel from a Base Station or Repeater to mobile stations NOTE: The forward CDMA channel contains one or more code channels that are transmitted on a CDMA frequency assignment using a particular pilot PN offset. High Rate Packet Data (HRPD): CDMA technique optimized for data communicat

49、ions in Type 2 cdma2000 systems maximum output power (Pmax): mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition mean power: total calorimetric power measured in a specified bandwidth at the antenna connector mobile station: station intended to be used while in motion or during halts at unspecified points NOTE: Mobile stations include portable units (e.g. hand-held personal units) and units installed in vehicles and HRPD access terminals. pass band: frequency range that the Repe