ETSI EN 300 832-1998 Electromagnetic Compatibility and Radio Spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) for Mobile Earth Stations (MES) Providing Low Bit Rate Data .pdf

《ETSI EN 300 832-1998 Electromagnetic Compatibility and Radio Spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) for Mobile Earth Stations (MES) Providing Low Bit Rate Data .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 832-1998 Electromagnetic Compatibility and Radio Spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) for Mobile Earth Stations (MES) Providing Low Bit Rate Data .pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-ETSI EN 300 832-ENGL 1998 m 3400855 02900b b2T m EN 300 832 vi .i .i (1998-03) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) for Mobile Earth Stations (MES) providing Low Bit Rate Data Communicat

2、ions (LBRDC) using satellites in Low Earth Orbits (LEO) operating in frequency bands below 1 GHz STD=ETSI EN 300 832-ENGL 1998 = 3400855 02900b8 Sbb 2 EN 300 832 Vl.l.1 (1998-03) Reference DEN/ERM-EMC-026 (7pcOOico.PDF) Keywords Earth station, EMC, MES, mobile, MSS, radio, satel lite ETSi Secretaria

3、t Postai address F-O6921 Sophia Antipolis Cedex - FRANCE Office address 650 Route des Lucioles - SoDhia AntiDolis Valbonne - FRANCE Siret ND 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) No 7803/88 Tel.: i-33 4 92 94 42 O0 Fax: +33 4 93 65 47

4、16 Internet secretariata etci.fr http:/www. etsi.fr http:/w.etsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in ail media. O European Telecommunications Standards Institute 1998. A

5、U rights reserved. - STD-ETSI EN 300 832-ENGL Ir998 3400855 0290069 4T2 = 3 EN 300 832 Vl.l.1 (1998-03) Contents Intellectual Property Rights 5 Foreword 5 1 Scope 6 2 References 6 3 Definitions and abbreviations 7 3.1 Definitions . 7 3.2 Abbreviations . 8 4 General test conditions . 9 4.1 Test condi

6、tions . 9 4.2 4.3 4.4.1 4.4.2 Arrangements for tests . 9 RF connection of test signals . 10 4.4 Exclusion band . 10 Transmitter exclusion band 10 Receiver exclusion bands 10 5 5.1 5.2 5.3 5.4 5.4.1 5.4.2 5.5 Performance assessment 10 General information to be provided by the applicant . 10 Equipment

7、 classification 11 Ancillary equipment . 11 MES connected to host equipment . 11 Alternative A . combined equipment . 11 Alternative B: use of a test jig 12 Equipment configuration(s) . 12 6 Performance criteria . 13 6.1 General . 13 6.2 Performance criteria for Continuous Phenomena (CP) 13 6.3 Perf

8、ormance criteria for Transient Phenomena (TP) . 13 7 Applicability overview tables 14 7.1 Emission 14 7.2 Immunity 14 8 8.1 8.2 8.2.1 8.2.2 8.2.3 8.3 8.3.1 8.3.2 8.3.3 8.4 8.4.1 8.4.2 8.4.3 Test methods and limits for emission tests of EUT . 14 Test Configuration . 14 Ancillary equipment enclosure .

9、 15 Purpose . 15 Test method 15 Test limit 15 DC power input/output port . 15 Test method 16 Test limit 16 AC mains power input/output port . 16 Test method 16 Test limit 16 Purpose . 16 Purpose . 16 9 Test methods and levels for immunity tests for EUT 17 9.1 Test configuration 17 9.2 Radio frequenc

10、y electromagnetic field (80 MHz - 1 O00 MHz) 17 9.2.1 Purpose . 17 9.2.2 Test method and level 18 9.2.3 Performance criteria . 18 9.3 Electrostatic discharge . 18 . 9.3.1 9.3.2 9.3.3 9.4 9.4.1 9.4.2 9.4.3 9.5 9.5.1 9.5.2 9.5.3 9.6 9.6.1 9.6.2 9.6.3 9.7 9.7.1 9.7.2 9.7.3 9.8 9.8.1 9.8.2 9.8.3 STD-ETS

11、I EN 300 832-ENGL 1778 3400855 0270070 114 4 EN 300 832 Vl.l.1 (1998-03) Purpose . 18 Test method and levels . 18 Performance criteria . Fast transients common mode 18 Purpose . 18 Test method and levels . 18 Performance criteria . 19 RF common mode (O, 15 MHz - 80 MHz) 19 Purpose . 19 Test method a

12、nd level 19 Performance criteria . 19 Transients and surges, vehicular environment . 20 Purpose Test method and level . Performance criteria . 21 Voltage dips and intemptions . 21 Purpose . 21 Test method and levels 21 Performance criteria . 21 Purpose . 21 Test method and levels . 22 Performance cr

13、iteria . 22 Surges, common and differential mode 21 Annex A (normative): Subclauses of the present document relevant for compliance with the essential requirements of relevant EC Council Directives 23 Definitions of the MES within the scope of the present document . 24 Annex B (normative): B.l MESS

14、operating below 1 GHz 24 Annex C (informative): Bibliography . 25 History 26 . - STD=ETSI EN 300 832-ENGL 1998 = 3400855 0290073 050 - 5 EN 300 832 Vl.1.l (1998-03) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The inform

15、ation pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members , and can be found in ETR 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSl standards“, which is available free of charge fr

16、om the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/www.etsi.fr/ipr). Pursuant to the ETSI Interim IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETR 3 1

17、4 (or the updates on http:/www.etsi.fr/ipr) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present do

18、cument is based upon the Generic Standards EN 50081-1 i and EN 50082-1 2. Other standards cover radio communications equipment not listed in the scope of the present document. The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Di

19、rective 83/189/EEC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document, together with ETS 300 721, is intended to become a Harmonized Standard, the reference of which will be published in the Official Jornal

20、of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/336/EEC as amended). Technical specifications relevant to the EMC Directive are given in annex A. National transposi

21、tion dates Date of adoption of this EN: Date of latest announcement of this EN (doa): 6 February 1998 31 May 1998 Date of latest publication of new National Standard or endorsement of this EN (dople): 30 November 1998 Date of withdrawal of any conflicting National Standard (dow): 30 November 1998 6

22、EN 300 832 Vl.l.1 (1998-03) 1 Scope The present document covers the assessment of Mobile Earth Stations (MESs) and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC) . Technical specifications related to the antenna port and emissions from the enclosure port of the equipment are n

23、ot included in the present document. Such specific technical specifications are found in the relevant product standard. The present document specifies the applicable EMC tests, the test methods, the limits and the minimum performance criteria for MESs providing Low Bit Rate Data Communications (LBRD

24、C) using satellites in Low Earth Orbit (LEO) and operating in frequency bands below 1 GHz, as defined in ETS 300 721 3, and ancillary equipment. In addition to the technical specification of the present document, there may be published in the Official Journal of the European Communities (OJEC) refer

25、ences to Harmonized EMC standards that apply to the products covered by the present document in their own right, for example, EN 61000-3-2 and EN 61000-3-3 (power frequency harmonics and voltage fluctuation). The environment classification used in the present document refers to the environment class

26、ification used in the Generic Standards EN 50081-1 i and EN 50082-1 2, except the vehicular environment class which refers to IS0 7637-1 4 and IS0 7637-2 5. The EMC requirements have been selected to ensure an adequate level of compatibility for apparatus at residential, commercial, light industrial

27、 and vehicular environments. The levels, however, do not cover extreme cases which may occur in any location but with a low probability of occurrence. The present document may not cover those cases where a potential source of interference, which is producing individually repeated transient phenomena

28、, or a continuous phenomenon, is permanently present, e.g. a radar or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied to either the source of interference, or the interfered p or all versions up to and including the identified version (identi

29、fied by “up to and including“ before the version identity); or all versions subsequent to and including the identified version (identified by “onwards“ following the version identity); or publications without mention of a specific version, in which case the latest version applies. A non-specific ref

30、erence to an ETS shall also be taken to refer to later versions published as an EN with the same number. il EN 50081-1 (1992): “Electromagnetic compatibility - Generic emission standard - Part 1: Residential, commercial and light industry“. EN 50082-1 (1993): “Electromagnetic compatibility - Generic

31、 immunity standard - Part 1: Residential, commercial and light industry“. VI STD.ETS1 EN 300 832-ENGL 1998 3400855 0290073 923 7 EN 300 832 Vl.l.1 (1998-03) ETS 300 721: “ Satellite Earth Stations and Systems (SES); MES providing Low Bit Rate Data Communications (LBRDC) using LEO satellites operatin

32、g below 1 GHz“. IS0 7637-1 (1990): “Road vehicles - Electrical disturbance by conduction and coupling - Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage - Electrical transient conduction along supply lines only“. IS0 7637-2 (1990): “Road vehicles - Electrical dis

33、turbance by conduction and coupling - Part 2 Commercial vehicles with nominal 24 V supply voltage - Electrical transient conduction along supply lines only“. EN 55022 (1994): “Limits and methods of measurement of radio disturbance characteristics of information technology equipment“. CISPR 16-1: “Sp

34、ecification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus“. EN 61000-4-3 (modified): “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 3: Radiated, radio-frequency, electromagn

35、etic field immunity test“. EN 61000-4-2: “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 2: Electrostatic discharge immunity test“. EN 61000-4-4: “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 4: Electrical fast

36、 transienthurst immunity test“. EN 61000-4-6: “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 6: Immunity to conducted disturbances, induced by radio-frequency fields“. EN 61000-4-1 1: “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement

37、techniques - Section 11: Voltage dips, short interruptions and voltage variations immunity tests“. EN 61000-4-5: “Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 5: Surge immunity test“. ETR 238: “ETSUCENELEC standardization programme for the development of

38、 Harmonized Standards related to Electro-Magnetic Compatibility (EMC) in the field of telecommunications“. 89/336/EEC: “Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility“. ITU Radio Regulations. 3 3.1 Definitions and abbreviations Def i

39、 n it ions For the purposes of the present document, the following definitions apply: ancillary equipment: Equipment (apparatus), where used in connection with a MES is considered as an ancillary equipment (apparatus) if - the equipment is intended for use in conjunction with a MES to provide additi

40、onal operational andor control features to the MES (e.g. to extend control to another position or location); and the equipment cannot be used on a stand alone basis to provide MES user functions independently of a MES; and the absence of the ancillary equipment does not inhibit the operation of the

41、MES. - - applicant: A party seeking an approval, or to place an MES on the European market, i.e. the manufacturer of the equipment, or his authorized representative, or an equipment supplier to the European market. 8 EN 300 832 Vl.l.1 (1998-03) carrier-on state: An MES is in this state when it is tr

42、ansmitting a signal in a continuous or non-continuous mode. carrier-off: An MES is in this state when it is not transmitting a signal, i.e. not in the carrier on state. enclosure port: The physical boundary of the apparatus through which an electromagnetic field may radiate or impinge (see figure 1)

43、. host equipment: Any equipment which has complete user functionality when not connected to the MES, and to which connection is necessary for the MES to offer additional functionality. Installable Equipment (IE), Internally Mounted Equipment (IME) and Externally Mounted Equipment (EME): An Installab

44、le Equipment (E) is an equipment which is intended to be installed in a vehicle. An E may consist of one or several modules. The E is composed of modules intended to be externally mounted and declared by the applicant as Externaily Mounted Equipment (EME). The remaining module(s) are defined as Inte

45、rnally Mounted Equipment (ME). integral antenna: An antenna which may not be removed during the tests, according to the applicant statement. occupied bandwidth: See ITU Radio Regulations 16, Part A, Chapter 1, Terminology RR 147. port: A particular interface of the specified equipment (apparatus) wi

46、th the electromagnetic environment (see figure 1). Enclosure port Signal / control ports APPARATUS Antenna port DC power port Figure: 1 Examples of ports portable equipment: A Portable Equipment (PE) is generally intended to be self-contained, free standing and portable. A PE would normally consist

47、of a single module, but may consist of several interconnected modules. NOTE: More than one of the equipment classifications can apply to certain equipment, as described in subclause 5.2, dependent upon the applicants declaration of normal intended use. removable antenna: An antenna which may be remo

48、ved for the test according to the applicant statement. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: BER CMF CP EiRP EMC EME EUT F-MES IE IME LBRDC LEO LISN MES MSS NCF OJEC PE Bit Error Ratio Control and Monitoring Functions Continuous Phenomena Equi

49、valent Isotropically Radiated Power ElectmMagnetic Compatibility Externally Mounted Equipment Equipment Under Test Fixed MES Installable Equipment Internally Mounted Equipment Low Bit Rate Data Communication Low Earth Orbit Line Impedance Stabilizing Network Mobile Earth Station Mobile Satellite Service Network Control Facilities Official Journal of the European Commission Portable Equipment PEP P-MES QWA RF STE TP ITlIS V-MES STD-ETSI EN 300 832-ENGL 1998 m 3Li00855 0290075 7Tb m 9 EN 300 832 V1.l.l (1998-0