ETSI EN 300 392-11-12-2003 Terrestrial Trunked Radio (TETRA) Voice Plus Data (V+D) Part 11 Supplementary Services Stage 2 Sub-Part 12 Call Hold (HOLD) (V1 1 2)《陆地集群无线电(TETRA) 语音加数据_1.pdf

《ETSI EN 300 392-11-12-2003 Terrestrial Trunked Radio (TETRA) Voice Plus Data (V+D) Part 11 Supplementary Services Stage 2 Sub-Part 12 Call Hold (HOLD) (V1 1 2)《陆地集群无线电(TETRA) 语音加数据_1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 392-11-12-2003 Terrestrial Trunked Radio (TETRA) Voice Plus Data (V+D) Part 11 Supplementary Services Stage 2 Sub-Part 12 Call Hold (HOLD) (V1 1 2)《陆地集群无线电(TETRA) 语音加数据_1.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 300 392- 1 1 -1 2 VI .I .2 (2003-05) European Sfandard (Telecommunica fions series) Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 11: Supplementary services stage 2; Sub-part 12: Call Hold (HOLD) 2 ETSI EN 300 392-1 1-12 VI .I .2 (2003-05) Reference REN/TETRA-03111-11-12 Key

2、words data, HOLD, radio, speech, stage 2, supplementary service, TETRA, V+D ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (0

3、6) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the refe

4、rence version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or cha

5、nge of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written

6、permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are T

7、rade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 ETSI EN 300 392-1 1-12 VI . 1 . 2 (2003-05) Contents Intellectual Property Rights 4 Foreword . 4 1 2

8、3 3.1 3.2 4 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.3 5 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.1.8 5.1.9 5.1.10 5.1.11 5.2 5.3 5.4 5.4.1 5.4.2 5.4.2.1 5.4.2.2 5.4.2.3 5.4.2.4 5.4.2.5 Scope 6 References 6 Definitions and abbreviations . 7 Definitions 7 Abbreviations . 7 Functional model 7 Fu

9、nctional model description 7 Description of functional entities 8 Served user functional entity, FE1 Affected user SwMI functional entity, FE25 8 Served user SwMI functional entit 9 Served user new SwMI functional en 9 9 Affected user functional entity, FE5 . 9 Relationship of functional model to ba

10、sic call functional model . 9 hformation flows . 10 Definition of information flows 10 INFORM 1 10 INFORM 2 10 INFORM 3 11 INTERROGATE 11 INTERROGATE ACK . 11 12 12 12 13 14 14 15 16 16 16 17 17 Successful retrieval of call on hold . 17 Invocation failure 18 Retrieval failure . 18 Migration of serve

11、d user with calls on hold 19 6 FE actions . 20 6.1 Functional Entity actions of FE 1 20 6.2 Functional Entity actions of FE2 1 21 6.3 Functional Entity actions of FE21 . 22 6.4 Functional Entity actions of FE25 22 6.5 Functional Entity actions of FE5 22 7 Allocation of functional entities to physica

12、l equipment . 23 8 Interworking considerations . 23 History 24 ETSI 4 ETSI EN 300 392-1 1-12 VI .I .2 (2003-05) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is

13、publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the E

14、TSI Web server (5). All published ETSI deliverables shall include information which directs the reader to the above source of information. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Terrestrial Trunked Radio (TETRA). The present document is part 11,

15、 sub-part 12 of a multi-part deliverable covering the Voice plus Data (V+D), as identified below: EN 300 392-1: EN 300 392-2: EN 300 392-3: ETS 300 392-4: EN 300 392-5: EN 300 392-7: EN 300 392-9: EN 300 392-10: EN 300 392-11: “General network design“; “Air Interface (AI)“; “Intenvorking at the Inte

16、r-System Interface (ISI)“; “Gateways basic operation“; “Peripheral Equipment Interface (PEI)“; “Security“; “General requirements for supplementary services“; “Supplementary services stage 1“; “Supplementary services stage 2“; ETS 300 392-11-1: ETS 300 392-1 1-2: ETS 300 392-11-3: EN 300 392-1 1-4: E

17、TS 300 392-1 1-5: ETS 300 392-1 1-6: ETS 300 392-1 1-7: EN 300 392-11-8: ETS 300 392-1 1-9: EN 300 392-1 1-10: ETS 300 392-11-11: EN 300 392-11-12: EN 300 392-1 1-12: ETS 300 392-11-13: Call Identification (CI) ; “Call Report (CR)“; “Talking Party Identification (TPI)“; “Call Forwarding (CF)“; “List

18、 Search Call (LSC)“; “Call Authorized by Dispatcher (CAD)“; “Short Number Addressing (SNA)“; “Area Selection (AS)“; “Access Priority (AP)“; “Priority Call (PC)“; “Call Waiting (CW)“; “Call Hold (CH)“; “Call Hold (CH)“; “Call Completion to Busy Subscriber (CCBS)“; ETSI 5 ETSI EN 300 392-1 1-12 VI .I

19、.2 (2003-05) EN 300 392-11-14: “Late Entry (LE)“; ETS 300 392-1 1-16: “Pre-emptive Priority Call (PPC)“; EN 300 392-1 1-17: “Include Call (IC)“; EN 300 392-1 1-18: “Barring of Outgoing Calls (BOC)“; EN 300 392-1 1-19: “Barring of Incoming Calls (BIC)“; ETS 300 392-1 1-20: “Discreet Listening (DL)“;

20、EN 300 392-1 1-21 : “Ambience Listening (AL)“; ETS 300 392-1 1-22: “Dynamic Group Number Assignment (DGNA)“; ETS 300 392-1 1-23: “Call Completion onNo Reply (CCNR)“; ETS 300 392-1 1-24: “Call Retention (CRT)“; EN 300 392-12: “Supplementary services stage 3“; ETS 300 392-13: “SDL model of the Air Int

21、erface (AI)“; ETS 300 392-14: “Protocol Implementation Conformance Statement (PICS) proforma specification“; TS 100 392-15: “TETRA frequency bands, duplex spacings and channel numbering“; TS 100 392-16: “Network Performance Metrics“; TS 100 392-17: “TETRA V+D and DMO Release 1.1 specifications“. I P

22、roposed national transposition dates I Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 3 1 August 2003 29 February 2004 29 February 2004 ETSI 6 ETSI EN

23、300 392-1 1-12 VI .I .2 (2003-05) 1 Scope The present document specifies the stage 2 description of the Supplementary Service Call Hold (SS-HOLD) for the Terrestrial Trunked Radio (TETRA). SS-HOLD enables a user to interrupt communication on an existing call and then subsequently, if desired, re-est

24、ablish communication. Man-Machine Interface (MMI) and charging principles are outside of the scope of the present document. Supplementary service specifications are produced in three stages according to the method defined in ITU-T Recommendation 1.130 i. The stage 2 description identifies the functi

25、onal capabilities and the information flows needed to support the supplementary service as specified in its stage 1 description (see EN 300 392-10-12 7). The stage 2 description is followed by the stage 3 description, which specifies the protocols at the air interface and at the various Inter-System

26、 Interfaces (ISI) to support the service. The present document is applicable to TETRA Voice plus Data terminal equipment and networks. 2 Re fe re nces The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are eithe

27、r specific (identified by date of publication andor edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expec

28、ted location might be found at htlu:/docbox.etsi.or:eerence. il ITU-T Recommendation I. 130: “Method for the characterization of telecommunication services supported by an ISDN and network capabilities of an ISDN“. ETSI EN 300 392-1: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 1

29、: General network design“. ETSI EN 300 392-2: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air Interface (AI)“. ETSI EN 300 392-3-2: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 3: Interworking at the Inter-System Interface (ISI); Sub-part 2: Additional Netwo

30、rk Feature Individual Call (ANF-ISIIC)“. 21 31 41 51 ETSI ETS 300 392-3-5: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 3: Interworking at the Inter-System Interface (ISI); Sub-part 5: Additional Network Feature for Mobility Management (ANF-ISIMM)“. ETSI EN 300 392-9: “Terrestrial

31、 Trunked Radio (TETRA); Voice plus Data (V+D); Part 9: General requirements for supplementary services“. ETSI EN 300 392-10-12: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 10: Supplementary services stage 1; Sub-part 12: Call Hold (CH)“. ETSI EN 300 392-12-12: “Terrestrial Trunke

32、d Radio (TETRA); Voice plus Data (V+D); Part 12: Supplementary services stage 3; Sub-part 12: Call Hold (CH)“. ETSI 7 ETSI EN 300 392-1 1-12 VI .I .2 (2003-05) 91 ISO/IEC 11574 (1994): “Information technology - Telecommunications and information exchange between systems - Private Integrated Services

33、 Network - Circuit-mode 64 kbit/s bearer services - Service description, functional capabilities and information flows“. 3 3.1 Definitions and abbreviations De fi nit ions For the purposes of the present document, the terms and definitions given in EN 300 392-9 6 apply with the following modificatio

34、ns: affected user: other party than the served user in an individual call served user: user participating in an individual call who invokes the supplementary service NOTE: When the served user has many calls on hold, he may be the calling party for some of them and the connected party for the others

35、. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ANF-ISIMM cc CCA NOTE: Additional Network Feature - Inter-System Interface Mobility Management Basic Service Call Control functional entity Basic Service Call Control functional entity agent CC and CCA a

36、re applied as defined in ISO/IEC 11574 9. FE GTSI HOLD IS1 ITS1 LS MS PISN SDL ss Functional Entity Group TETRA Subscriber Identity Call Hold Inter-System Interface Individual TETRA Subscriber Identity Line Station Mobile Station Private Intergrated Services Network Specification and Description Lan

37、guage Supplementary Service NOTE: SwMI Switching and Management Infiastructure TNSS-SAP The abbreviation SS is only used when referring to a specific supplementary service (e.g. SS-HOLD). TETRA Network Layer Supplementary Services-Service Access Point 4 Functional model 4.1 Functional model descript

38、ion The functional model shall comprise the following Functional Entities (FES): FE 1 FE2 1 FE2 1 FE25 Affected user SwMI FE FE5 Affected user FE Served user functional entity Served user SwMI FE Served user new SwMI FE ETSI 8 ETSI EN 300 392-1 1-12 VI .I .2 (2003-05) The following relationships sha

39、ll exist: ra between FE1 and FE21 rb between FE21 and FE5+ rc between FE21 and FE25 rd between FE2 1 and FE2 1 Figure 1 shows these FES and relationships for the basic operational part of SS-HOLD, when the served user does not change location after he has put a (individual) call on hold. rb Figure 1

40、: Functional model for the basic operational part of SS-HOLD Figure 2 shows these FES and relationships for the operational part of SS-HOLD, when the served user changes location after he has put a (individual) call on hold. rb rc Figure 2: Functional model for the operational part of SS-HOLD with l

41、ocation change of the served user NOTE: Both figures 1 and 2 apply only in the case of individual call since SS-HOLD does not apply to group call. 4.2 Description of functional entities 4.2.1 Served user functional entity, FEI FE1 is the functional entity that serves the calling user for the invocat

42、ion of SS-HOLD. If the served user changes location with one or more individual call still on hold, FE1 may be informed by FE21 about possible changes for those calls. It will process that information according to its contents; notably if it indicates a call reference change for some calls on hold,

43、it will update accordingly its call references for those calls. FE1 may also relay the interrogation requests received from the served user to FE21, and the corresponding responses from FE21 to the served user (as indication primitives). ETSI 9 ETSI EN 300 392-1 1-12 VI .I .2 (2003-05) 4.2.2 Served

44、user SwMI functional entity, FE21 When it receives a SS-HOLD invocation from FE1, FE21 checks whether SS-HOLD has been activated (i.e. subscribed) and, if so, puts the call on hold, in informing FE5 and FE25. If the served user changes location with an individual call still on hold, FE21 may attempt

45、 to create FE21. If that attempt is successful, FE21 passes the data about that call to FE21. If not, it informs the collocated individual call control entity about the situation. 4.2.3 Served user new SwMI functional entity, FE21 If the served user changes location with a call still on hold, FE21 m

46、ay be created. FE21 then receives the data about that call, informs FE1 about the calls on hold for which one of the two following changes has occurred due to the location change: call reference changed or call lost. After that FE21 replaces FE21. 4.2.4 Affected user SwMI functional entity, FE25 FE2

47、5 receives from FE21 the information that SS-HOLD has been invoked (by the served user) for the call and passes it to the collocated individual call control entity. 4.2.5 Affected user functional entity, FE5 FE5 is the functional entity that serves the affected user to inform him when the call has b

48、een put on hold and then, when it is retrieved. 4.3 Relationship of functional model to basic call functional model Although no formal models have been defined for basic individual call or for basic group call, those models can be readily derived from the PISN model for basic call, in ISO/IEC 11574

49、9. FE1 shall be collocated with the CCA of the calling user or of the called user in an individual call. FE21 shall be collocated with the CC functional entity in the served user SwMI in an individual call. Depending on whether the served user has roamed or migrated (with one or more individual calls on hold), FE21 shall be collocated with the CC functional entity either: in the same served user SwMI if the served user has roamed; in the served user new SwMI if the served user has migrated. FE5 shall be collocated with the CCA of the remote party in an in