ETSI 3GPP TS 34 121-2003 See TS 134 121 V5 0 0 (Version 5 0 0 Release 5).pdf

《ETSI 3GPP TS 34 121-2003 See TS 134 121 V5 0 0 (Version 5 0 0 Release 5).pdf》由会员分享，可在线阅读，更多相关《ETSI 3GPP TS 34 121-2003 See TS 134 121 V5 0 0 (Version 5 0 0 Release 5).pdf（410页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 134 121 V4.0.0 (2003-06)Technical Specification Universal Mobile Telecommunications System (UMTS);Terminal Conformance Specification;Radio Transmission and Reception (FDD)(3GPP TS 34.121 version 4.0.0 Release 4)ETSI ETSI TS 134 121 V4.0.0 (2003-06) 1 3GPP TS 34.121 version 4.0.0 Release 4 R

2、eference RTS/TSGT-0134121v400 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Ind

3、ividual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Docum

4、ent Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the c

5、urrent status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and th

6、e foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being regist

7、ered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 134 121 V4.0.0 (2003-06) 2 3GPP TS 34.121 version 4.0.0 Release 4 Intellectual Property Rights IPRs essential or potentially ess

8、ential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs noti

9、fied to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee ca

10、n be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP

11、). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be foun

12、d under http:/webapp.etsi.org/key/queryform.asp . ETSI ETSI TS 134 121 V4.0.0 (2003-06) 3 3GPP TS 34.121 version 4.0.0 Release 4 Contents Intellectual Property Rights2 Foreword.2 Foreword.15 1 Scope 16 2 References 16 3 Definitions, symbols, abbreviations and equations 17 3.1 Definitions17 3.2 Symbo

13、ls17 3.3 Abbreviations .17 3.4 Equations18 4 Frequency bands and channel arrangement19 4.1 General .19 4.2 Frequency bands.19 4.3 TXRX frequency separation.20 4.4 Channel arrangement20 4.4.1 Channel spacing20 4.4.2 Channel raster .20 4.4.3 Channel number20 4.4.4 UARFCN 20 5 Transmitter Characteristi

14、cs.21 5.1 General .21 5.2 Maximum Output Power 21 5.2.1 Definition and applicability 21 5.2.2 Minimum Requirements .22 5.2.3 Test purpose22 5.2.4 Method of test .22 5.2.4.1 Initial conditions .22 5.2.4.2 Procedure 22 5.2.5 Test requirements22 5.3 Frequency Error23 5.3.1 Definition and applicability

15、23 5.3.2 Minimum Requirements .23 5.3.3 Test purpose23 5.3.4 Method of test .23 5.3.5 Test Requirements 24 5.4 Output Power Dynamics in the Uplink.24 5.4.1 Open Loop Power Control in the Uplink24 5.4.1.1 Definition and applicability.24 5.4.1.2 Minimum requirements.24 5.4.1.3 Test purpose 24 5.4.1.4

16、Method of test .25 5.4.1.5 Test requirements25 5.4.2 Inner Loop Power Control in the Uplink 26 5.4.2.1 Definition and applicability.26 5.4.2.2 Minimum requirements.26 5.4.2.3 Test purpose 27 5.4.2.4 Method of test .27 5.4.2.5 Test requirements31 5.4.3 Minimum Output Power .33 5.4.3.1 Definition and

17、applicability.33 5.4.3.2 Minimum Requirements33 5.4.3.3 Test purpose 33 5.4.3.4 Method of test .33 ETSI ETSI TS 134 121 V4.0.0 (2003-06) 4 3GPP TS 34.121 version 4.0.0 Release 4 5.4.3.5 Test requirements34 5.4.4 Out-of-synchronisation handling of output power34 5.4.4.1 Definition and applicability.3

18、4 5.4.4.2 Minimum Requirements34 5.4.4.3 Test purpose 36 5.4.4.4 Method of test .36 5.4.4.5 Test requirements37 5.5 Transmit ON/OFF Power .37 5.5.1 Transmit OFF Power 37 5.5.1.1 Definition and applicability.37 5.5.1.2 Minimum Requirements37 5.5.1.3 Test purpose 37 5.5.1.4 Method of test .37 5.5.1.5

19、Test requirements37 5.5.2 Transmit ON/OFF Time mask38 5.5.2.1 Definition and applicability.38 5.5.2.2 Minimum requirements.38 5.5.2.3 Test purpose 39 5.5.2.4 Method of test .39 5.5.2.5 Test requirements40 5.6 Change of TFC .40 5.6.1 Definition and applicability 40 5.6.2 Minimum requirements.41 5.6.3

20、 Test purpose42 5.6.4 Method of test .42 5.6.5 Test requirements42 5.7 Power setting in uplink compressed mode .43 5.7.1 Definition and applicability 43 5.7.2 Minimum requirements.43 5.7.3 Test purpose44 5.7.4 Method of test .45 5.7.5 Test requirements52 5.8 Occupied Bandwidth (OBW) .53 5.8.1 Defini

21、tion and applicability 53 5.8.2 Minimum Requirements .53 5.8.3 Test purpose54 5.8.4 Method of test .54 5.8.5 Test Requirements 54 5.9 Spectrum emission mask 54 5.9.1 Definition and applicability 54 5.9.2 Minimum Requirements .55 5.9.3 Test purpose55 5.9.4 Method of test .55 5.9.4.1 Initial condition

22、s .55 5.9.4.2 Procedure 55 5.9.5 Test requirements56 5.10 Adjacent Channel Leakage Power Ratio (ACLR)56 5.10.1 Definition and applicability 56 5.10.2 Minimum Requirements .57 5.10.3 Test purpose57 5.10.4 Method of test .57 5.10.5 Test requirements58 5.11 Spurious Emissions 58 5.11.1 Definition and a

23、pplicability 58 5.11.2 Minimum Requirements .58 5.11.3 Test purpose59 5.11.4 Method of test .59 5.11.5 Test requirements60 5.12 Transmit Intermodulation.60 5.12.1 Definition and applicability 60 5.12.2 Minimum Requirements .61 5.12.3 Test purpose61 ETSI ETSI TS 134 121 V4.0.0 (2003-06) 5 3GPP TS 34.

24、121 version 4.0.0 Release 4 5.12.4 Method of test .61 5.12.5 Test requirements61 5.13 Transmit Modulation62 5.13.1 Error Vector Magnitude (EVM) .62 5.13.1.1 Definition and applicability.62 5.13.1.2 Minimum Requirements62 5.13.1.3 Test purpose 62 5.13.1.4 Method of test .62 5.13.1.5 Test requirements

25、63 5.13.2 Peak code domain error 63 5.13.2.1 Definition and applicability.63 5.13.2.2 Minimum Requirements63 5.13.2.3 Test purpose 63 5.13.2.4 Method of test .64 5.13.2.5 Test requirements64 6 Receiver Characteristics.65 6.1 General .65 6.2 Reference Sensitivity Level65 6.2.1 Definition and applicab

26、ility 65 6.2.2 Minimum Requirements .66 6.2.3 Test purpose66 6.2.4 Method of test .66 6.2.5 Test requirements66 6.3 Maximum Input Level67 6.3.1 Definition and applicability 67 6.3.2 Minimum requirements.67 6.3.3 Test purpose67 6.3.4 Method of test .67 6.3.5 Test requirements68 6.4 Adjacent Channel S

27、electivity (ACS)68 6.4.1 Definition and applicability 68 6.4.2 Minimum Requirements .68 6.4.3 Test purpose69 6.4.4 Method of test .69 6.4.5 Test requirements69 6.5 Blocking Characteristics.70 6.5.1 Definition and applicability 70 6.5.2 Minimum Requirements .70 6.5.2.1 Minimum Requirements (In-band b

28、locking).70 6.5.2.2 Minimum requirements (Out of-band blocking) .70 6.5.2.3 Minimum requirements (Narrow band blocking)71 6.5.3 Test purpose71 6.5.4 Method of test .72 6.5.5 Test requirements72 6.6 Spurious Response .73 6.6.1 Definition and applicability 73 6.6.2 Minimum Requirements .74 6.6.3 Test

29、purpose74 6.6.4 Method of test .74 6.6.5 Test requirements75 6.7 Intermodulation Characteristics75 6.7.1 Definition and applicability 75 6.7.2 Minimum Requirements .75 6.7.3 Test purpose76 6.7.4 Method of test .76 6.7.5 Test requirements77 6.8 Spurious Emissions 77 6.8.1 Definition and applicability

30、 77 6.8.2 Minimum Requirements .77 6.8.3 Test purpose78 6.8.4 Method of test .78 ETSI ETSI TS 134 121 V4.0.0 (2003-06) 6 3GPP TS 34.121 version 4.0.0 Release 4 6.8.5 Test requirements79 7 Performance requirements79 7.1 General .79 7.1.1 Measurement Configurations80 7.1.2 Definition of Additive White

31、 Gaussian Noise (AWGN) Interferer 80 7.2 Demodulation in Static Propagation conditions .80 7.2.1 Demodulation of Dedicated Channel (DCH)80 7.2.1.1 Definition and applicability.80 7.2.1.2 Minimum requirements.81 7.2.1.3 Test purpose 81 7.2.1.4 Method of test .81 7.2.1.5 Test requirements82 7.3 Demodu

32、lation of DCH in Multi-path Fading Propagation conditions82 7.3.1 Single Link Performance 82 7.3.1.1 Definition and applicability.82 7.3.1.2 Minimum requirements.82 7.3.1.3 Test purpose 85 7.3.1.4 Method of test .85 7.3.1.5 Test requirements85 7.4 Demodulation of DCH in Moving Propagation conditions

33、 88 7.4.1 Single Link Performance 88 7.4.1.1 Definition and applicability.88 7.4.1.2 Minimum requirements.88 7.4.1.3 Test purpose 89 7.4.1.4 Method of test .89 7.4.1.5 Test requirements89 7.5 Demodulation of DCH in Birth-Death Propagation conditions90 7.5.1 Single Link Performance 90 7.5.1.1 Definit

34、ion and applicability.90 7.5.1.2 Minimum requirements.90 7.5.1.3 Test purpose 90 7.5.1.4 Method of test .91 7.5.1.5 Test requirements91 7.6 Demodulation of DCH in downlink Transmit diversity modes91 7.6.1 Demodulation of DCH in open-loop transmit diversity mode91 7.6.1.1 Definition and applicability

35、.91 7.6.1.2 Minimum requirements.92 7.6.1.3 Test purpose 92 7.6.1.4 Method of test .92 7.6.1.5 Test Requirements.93 7.6.2 Demodulation of DCH in closed loop transmit diversity mode94 7.6.2.1 Definition and applicability.94 7.6.2.2 Minimum requirements.94 7.6.2.3 Test purpose 94 7.6.2.4 Method of tes

36、t .95 7.6.2.5 Test Requirements.96 7.6.3 Demodulation of DCH in Site Selection Diversity Transmission Power Control mode.97 7.6.3.1 Definition and applicability.97 7.6.3.2 Minimum requirements.97 7.6.3.3 Test purpose 97 7.6.3.4 Method of test .98 7.6.3.5 Test Requirements.101 7.7 Demodulation in Han

37、dover conditions.102 7.7.1 Demodulation of DCH in Inter-Cell Soft Handover .102 7.7.1.1 Definition and applicability.102 7.7.1.2 Minimum requirements.102 7.7.1.3 Test purpose 103 7.7.1.4 Method of test .103 7.7.1.5 Test requirements103 7.7.2 Combining of TPC commands from radio links of different ra

38、dio link sets.104 7.7.2.1 Definition and applicability.104 ETSI ETSI TS 134 121 V4.0.0 (2003-06) 7 3GPP TS 34.121 version 4.0.0 Release 4 7.7.2.2 Minimum requirements.104 7.7.2.3 Test purpose 105 7.7.2.4 Method of test .105 7.7.2.5 Test requirements106 7.8 Power control in downlink .107 7.8.1 Power

39、control in the downlink, constant BLER target .107 7.8.1.1 Definition and applicability.107 7.8.1.2 Minimum requirements.108 7.8.1.3 Test purpose 108 7.8.1.4 Method of test .108 7.8.1.5 Test Requirements.109 7.8.2 Power control in the downlink, initial convergence109 7.8.2.1 Definition and applicabi

40、lity.109 7.8.2.2 Minimum requirements.110 7.8.2.3 Test purpose 110 7.8.2.4 Method of test .110 7.8.2.5 Test Requirements.111 7.8.3 Power control in the downlink, wind up effects .112 7.8.3.1 Definition and applicability.112 7.8.3.2 Minimum requirements.112 7.8.3.3 Test purpose 112 7.8.3.4 Method of

41、test .113 7.8.3.5 Test Requirements.113 7.9 Downlink compressed mode 114 7.9.1 Single link performance114 7.9.1.1 Definition and applicability.114 7.9.1.2 Minimum requirements.114 7.9.1.3 Test purpose 115 7.9.1.4 Method of test .115 7.9.1.5 Test requirements115 7.10 Blind transport format detection.

42、116 7.10.1 Definition and applicability 116 7.10.2 Minimum requirements.117 7.10.3 Test purpose117 7.10.4 Method of test .117 7.10.5 Test requirements118 8 Requirements for support of RRM.119 8.1 General .119 8.2 Idle Mode Tasks .119 8.2.1 Cell Selection119 8.2.2 Cell Re-Selection 119 8.2.2.1 Scenar

43、io 1: Single carrier case 119 8.2.2.1.1 Definition and applicability.119 8.2.2.1.2 Minimum requirement.119 8.2.2.1.3 Test purpose 119 8.2.2.1.4 Method of test119 8.2.2.1.5 Test requirements 122 8.2.2.2 Scenario 2: Multi carrier case122 8.2.2.2.1 Definition and applicability.122 8.2.2.2.2 Minimum req

44、uirement.122 8.2.2.2.3 Test purpose 123 8.2.2.2.4 Method of test123 8.2.2.2.5 Test requirements 125 8.2.3 UTRAN to GSM Cell Re-Selection126 8.2.3.1 Scenario 1: Both UTRA and GSM level changed.126 8.2.3.1.1 Definition and applicability.126 8.2.3.1.2 Minimum requirement.126 8.2.3.1.3 Test purpose 127

45、8.2.3.1.4 Method of test127 8.2.3.1.5 Test requirements 128 8.2.3.2 Scenario 2: Only UTRA level changed.129 ETSI ETSI TS 134 121 V4.0.0 (2003-06) 8 3GPP TS 34.121 version 4.0.0 Release 4 8.2.3.2.1 Definition and applicability.129 8.2.3.2.2 Minimum requirement.129 8.2.3.2.3 Test purpose 130 8.2.3.2.4

46、 Method of test130 8.2.3.2.5 Test requirements 131 8.2.4 FDD/TDD Cell Re-selection.132 8.2.4.1 Definition and applicability.132 8.2.4.2 Minimum requirement 132 8.2.4.3 Test purpose 132 8.2.4.4 Method of test .132 8.2.4.5 Test requirements134 8.3 UTRAN Connected Mode Mobility.135 8.3.1 FDD/FDD Soft H

47、andover.135 8.3.1.1 Definition and applicability.135 8.3.1.2 Minimum requirement 135 8.3.1.3 Test purpose 135 8.3.1.4 Method of test .135 8.3.1.5 Test requirements140 8.3.2 FDD/FDD Hard Handover140 8.3.2.1 FDD/FDD Hard Handover to intra-frequency cell140 8.3.2.1.1 Definition and applicability.140 8.

48、3.2.1.2 Minimum requirement.140 8.3.2.1.3 Test purpose 141 8.3.2.1.4 Method of test141 8.3.2.1.5 Test requirements 147 8.3.2.2 FDD/FDD Hard Handover to inter-frequency cell147 8.3.2.2.1 Definition and applicability.147 8.3.2.2.2 Minimum requirement.147 8.3.2.2.3 Test purpose 148 8.3.2.2.4 Method of

49、test148 8.3.2.2.5 Test requirements 153 8.3.3 FDD/TDD Handover 153 8.3.3.1 Definition and applicability.153 8.3.3.2 Minimum requirement 153 8.3.3.3 Test purpose 154 8.3.3.4 Method of test .154 8.3.3.5 Test requirements160 8.3.4 Inter-system Handover from UTRAN FDD to GSM161 8.3.4.1 Definition and applicability.161 8.3.4.2 Minimum requirement.161 8.3.4.3 Test purpose 161 8.3.4.4 Method of test161 8.3.4.5 Test requirements 165 8.3.5 Cell Re-selection in CELL_FACH .165 8.3.5.1 One frequency present in neighbour list165 8.3.5.1.1 Definition and applicability.165 8.3.5.1.2 Minimum