EN ISO 17130-2013 en Leather - Physical and mechanical tests - Determination of dimensional change《皮革 物理和机械试验 尺寸变化测定》.pdf

《EN ISO 17130-2013 en Leather - Physical and mechanical tests - Determination of dimensional change《皮革 物理和机械试验 尺寸变化测定》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 17130-2013 en Leather - Physical and mechanical tests - Determination of dimensional change《皮革 物理和机械试验 尺寸变化测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 17130:2013Leather Physical andmechanical tests Determination of dimensionalchange (ISO 17130:2013)BS EN ISO 17130:2013 BRITISH STANDARDNational forewordThis British Sta

2、ndard is the UK implementation of EN ISO17130:2013.The UK participation in its preparation was entrusted to TechnicalCommittee TCI/69, Footwear, leather and coated fabrics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purpo

3、rt to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 74446 4ICS 59.140.30Compliance with a British Standard cannot confer immunity fromlegal obligations.

4、This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17130 May 2013 ICS 59.140.30 English Version Leather - Physical and mecha

5、nical tests - Determination of dimensional change (ISO 17130:2013) Cuir - Essais physiques et mcaniques - Dtermination des variations dimensionnelles (ISO 17130:2013) Leder - Physikalische und mechanische Prfung - Bestimmung der Mahaltigkeit (ISO 17130:2013) This European Standard was approved by CE

6、N on 25 April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

7、may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifie

8、d to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icela

9、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre:

10、 Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17130:2013: EBS EN ISO 17130:2013EN ISO 17130:2013 (E) 3 Foreword This document (EN ISO 17130:2013) has been prepared by IULTCS “Internatio

11、nal Union of Leather Technologists and Chemists Societies“ in collaboration with Technical Committee CEN/TC 289 “Leather” the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

12、 the latest by November 2013, and conflicting national standards shall be withdrawn at the latest by November 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying a

13、ny or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Repu

14、blic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 17130:2013 has been ap

15、proved by CEN as EN ISO 17130:2013 without any modification. BS EN ISO 17130:2013ISO 17130:2013(E)IULTCS/IUP 55:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Principle 14 Apparatus and materials 15 Sampling and sample preparation 16 Procedure. 2

16、7 Expression of results 38 Test report . 4BS EN ISO 17130:2013ISO 17130:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS

17、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c

18、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Dra

19、ft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this docum

20、ent may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 17130 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, in collaboration with the Physical Tests Commission of the Inte

21、rnational Union of Leather Technologists and Chemists Societies (IUP Commission, IULTCS), in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).IULTCS, originally formed in 1897, is a worldwide organization of professional leather societies to further the a

22、dvancement of leather science and technology. IULTCS has three Commissions, which are responsible for establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an international standardizing body for the preparation of test methods for leather.IULTCS/IUP 55

23、:2013(E)iv ISO 2013 All rights reservedBS EN ISO 17130:2013INTERNATIONAL STANDARDISO 17130:2013(E)IULTCS/IUP 55:2013(E)Leather - Physical and mechanical tests - Determination of dimensional change1 ScopeThis International Standard specifies a method of determining the dimensional change (shrinkage)

24、of leathers caused by ageing. It is applicable to all leathers.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the

25、latest edition of the referenced document (including any amendments) applies.ISO 105-B06, Textiles Tests for colour fastness Part B06: Colour fastness and ageing to artificial light at high temperatures: Xenon arc fading lamp testISO 2418, Leather Chemical, physical and mechanical and fastness tests

26、 Sampling locationISO 2419, Leather Physical and mechanical tests Sample preparation and conditioningISO 17228, Leather Tests for colour fastness Change in colour with accelerated ageing3 PrincipleA conditioned test piece is aged using the conditions defined in ISO 17228. The shrinkage is determined

27、 after reconditioning.4 Apparatus and materials4.1 Oven, as specified in ISO 17228.4.2 Climate chamber, as specified in ISO 17228.4.3 Vernier calliper, reading to 0,1 mm.4.4 Support, glass plate covered with a polyester nonwoven fabric (as specified in ISO 105-B06).NOTE The glass plate support keeps

28、 the test piece flat and the polyester fabric stops the test piece from sticking to the glass.4.5 Press knife, square, as specified in ISO 2419 with inner walls measuring 150 mm 1 mm.4.6 Indelible marker.5 Sampling and sample preparation5.1 Sample in accordance with ISO 2418. Cut at least two test p

29、ieces (150 150) mm for each of the ageing conditions required, by applying the press knife (4.5) to the grain surface, if distinguishable. ISO 2013 All rights reserved 1BS EN ISO 17130:2013ISO 17130:2013(E)NOTE For some applications, it can be necessary to use larger test pieces e.g. (300 300) mm to

30、 enhance the accuracy, especially in the case of low shrinkage.5.2 Using an indelible marker (4.6), mark the lines and measurement reference points A, B, C and D on the test pieces. Mark a square with a length of (100 1) mm (Figure 1).Dimensions in millimetres 1 mmFigure 1 Location of lines and meas

31、urement reference points on a test pieceIf test pieces with another dimension, e.g. (300 300) mm, are used, a square should be marked with a distance to each edge of (25 1) mm.5.3 Condition the test pieces in accordance with ISO 2419 for at least 48 h.6 Procedure6.1 Measure the distances AB, CD, AC

32、and BD on each test piece using the vernier calliper (4.3).6.2 Preheat the oven (4.1) to the test temperature or adjust the climate chamber (4.2) to the starting conditions. Place the test pieces with the grain side, top side or coated side downward on the support (4.4) in the centre of the oven or

33、climate chamber.To allow a fast exchange of humidity, it is necessary to place the leather in such a way that an intensive contact of the air in the oven or climate chamber with the flesh side of the leather is guaranteed.6.3 Age the test pieces as described in ISO 17228.6.4 If required, measure the

34、 distances between the measurement points following the description in 6.1 immediately after ageing (not later than 5 min). In this case, report that the measurement was made immediately.IULTCS/IUP 55:2013(E)2 ISO 2013 All rights reservedBS EN ISO 17130:2013ISO 17130:2013(E)6.5 Recondition the test

35、pieces for at least 48 h in accordance with ISO 2419.6.6 Measure the distances between the measurement points following the description in 6.1.6.7 Note any visual changes of the test piece, such as distortion and any changes in flexibility and softness manually.7 Expression of results7.1 The shrinka

36、ge may be expressed as linear shrinkage (see 7.2) or loss of area (area shrinkage)(see 7.3).7.2 The linear shrinkage is calculated using Formulae (1), (2) and (3).Calculate the mean of original length, L1, bounded by the points ABCD on the test piece, as follows:Lacbd111114=+ () (1)where a1, b1, c1,

37、 and d1are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured before the test.Calculate the mean of length after the test, L2, bounded by the points ABCD on the test piece, as follows:Lacbd222224=+ () (2)where a2, b2, c2and d2are the values of the dimensions AB, BD, CD

38、, AC respectively (see Figure 1), measured after the test.Calculate the percentage linear shrinkage SLusing the Formula (3):SLLLL=121100 (3)whereL1is the mean of original length, calculated from Formula (1);L2is the mean of length after the test, calculated from Formula (2).7.3 For the calculation o

39、f loss of area (area shrinkage) SAproceed as follows:Calculate the original area, A1, bounded by the points ABCD on the test piece, as follows:Aacbd1111122=+(4)where a1, b1, c1and d1are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured before the test.Calculate the ar

40、ea after the test, A2, bounded by the points ABCD on the test piece, as follows:Aacbd222 22=+(5)where a2, b2, c2and d2are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured after the test.IULTCS/IUP 55:2013(E) ISO 2013 All rights reserved 3BS EN ISO 17130:2013ISO 17130

41、:2013(E)Calculate the percentage loss of area (area shrinkage) SA, using Formula (6):SAAAA=121100 (6)whereA1is the original area, calculated from Formula (4);A2is the area after the test, calculated from Formula (5).8 Test reportThe test report shall include the following:a) reference to this Intern

42、ational Standard, i.e. ISO 17130;b) full details for identification of the sample and any deviation from ISO 2418 with respect to sampling;c) the test conditions used for ageing;d) mean value of the percentage linear shrinkage SLas calculated in 7.2 or mean value of percentage loss in area SA(area s

43、hrinkage) as calculated in 7.3 to the nearest 0,1 %;e) details of any visual changes or changes in flexibility and softness;f) the standard atmosphere used for conditioning and testing as given in ISO 2419;g) any deviations from the method specified in this International Standard.IULTCS/IUP 55:2013(

44、E)4 ISO 2013 All rights reservedBS EN ISO 17130:2013This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standa

45、rds in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9

46、001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be gratefu

47、l if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20

48、8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions

49、 of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherw