EN ISO 10140-1-2010 6875 Acoustics - Laboratory measurement of sound insulation of building elements - Part 1 Application rules for specific products (Incorporates Amendment A2 201.pdf

《EN ISO 10140-1-2010 6875 Acoustics - Laboratory measurement of sound insulation of building elements - Part 1 Application rules for specific products (Incorporates Amendment A2 201.pdf》由会员分享，可在线阅读，更多相关《EN ISO 10140-1-2010 6875 Acoustics - Laboratory measurement of sound insulation of building elements - Part 1 Application rules for specific products (Incorporates Amendment A2 201.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10140-1:2010Acoustics Laboratorymeasurement of soundinsulation of building elementsPart 1: Application rules for specificproducts+A1:2012Copyright European Committee fo

2、r Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 10140-1:2010+A1:2012National forewordThis British Standard is the UK implementation of EN ISO 10140-1:2010+A1:2012. It is identical to ISO 10140-1:2010

3、, incorporating amendment 1:2012. It supersedes BS EN ISO 10140-1:2010 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to ISO text carry the number of the ISO amendment. For example, text altered by ISO amen

4、dment 1 is indicated by .This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012. ISBN 978 0 580 70953 1ICS 91.120.20Compliance with a B

5、ritish Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31st March 2011.Amendments/corrigenda issued since publicationDate Text affected31 March 2012 Implementation of ISO amendment 1:2012

6、 with CEN endorsement A1:2012BRITISH STANDARDThe UK participation in its preparation was entrusted by Technical Committee EH/1, Acoustics, to Subcommittee EH/1/6, Building acoustics.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Copyright Europea

7、n Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10140-1:2010+A1 February 2012ICS 91.120.20 English Version Acoustics - Laboratory measurem

8、ent of sound insulation of building elements - Part 1: Application rules for specific products (ISO 10140-1:2010) Acoustique - Mesurage en laboratoire de lisolation acoustique des lments de construction - Partie 1: Rgles dapplication pour produits particuliers (ISO 10140-1:2010)Akustik - Messung der

9、 Schalldmmung von Gebudeteilen im Prfstand - Teil 1: Anwendungsregeln fr bestimmte Produkte (ISO 10140-1:2010) This European Standard was approved by CEN on 14 August 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europe

10、an Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English

11、, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

12、roatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDA

13、RDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10140-1:2010: ESupersedes EN ISO 10140-1:2010Copy

14、right European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3 Foreword This document (EN ISO 10140-1:2010) has been prepared by Technical Committee ISO/TC 43 “Acoustics“ in collaboration with Te

15、chnical Committee CEN/TC 126 “Acoustic properties of building elements and of buildings” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and

16、conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This do

17、cument supersedes EN 20140-10:1992, EN ISO 140-3:1995, EN ISO 140-1:1997, EN ISO 140-11:2005, EN ISO 140-6:1998, EN ISO 140-16:2006, EN ISO 140-8:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europ

18、ean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and th

19、e United Kingdom. Endorsement notice The text of ISO 10140-1:2010 has been approved by CEN as a EN ISO 10140-1:2010 without any modification. Foreword to amendment A1This document (EN ISO 10140-1:2010/A1:2012) has been prepared by Technical Committee ISO/TC 43 “Acoustics“ in collaboration with Techn

20、ical Committee CEN/TC 126 “Acoustic properties of building elements and of buildings” the secretariat of which is held by AFNOR. This Amendment to the European Standard EN ISO 10140:2010 shall be given the status of a national standard, either by publication of an identical text or by endorsement, a

21、t the latest by August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

22、or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece

23、, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10140-1:2010/Amd 1:2012 has been approved by CEN as a EN ISO 101

24、40-1:2010/A1:2012 without any modification. BS EN ISO 10140-1:2010+A1:2012 EN ISO 10140-1:2010+A1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-iiiContents Page Forewor

25、d iv Introduction.v 1 Scope1 2 Normative references1 3 General .1 4 Structure of application rules for specific products2 Annex A (normative) Walls Airborne sound insulation3 Annex B (normative) Doors Airborne sound insulation.5 Annex C (normative) Windows Airborne sound insulation .6 Annex D (norma

26、tive) Glazing Airborne sound insulation8 Annex E (normative) Small technical elements Airborne sound insulation 11 Annex F (normative) Floors Airborne and impact sound insulation 15 Annex G (normative) Acoustical linings Improvement of airborne sound insulation 16 Annex H (normative) Floor coverings

27、 Improvement of impact sound insulation .20 Annex I (normative) Shutters Airborne sound insulation28 Bibliography43 BS EN ISO 10140-1:2010+A1:2012 EN ISO 10140-1:2010+A1:2012 (E) ISO 2012Annex J (normative) Joints filled with fillers or seals Sound reduction index 32Copyright European Committee for

28、Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepar

29、ing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in li

30、aison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of

31、 technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is

32、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10140-1 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building acoustics. This

33、 first edition of ISO 10140-1, together with ISO 10140-2, ISO 10140-3, ISO 10140-4 and ISO 10140-5, cancels and replaces ISO 140-1:1997, ISO 140-3:1995, ISO 140-6:1998, ISO 140-8:1997, ISO 140-10:1991, ISO 140-11:2005 and ISO 140-16:2006, which have been technically revised. It also incorporates the

34、 Amendments ISO 140-1:1997/Amd.1:2004 and ISO 140-3:1995/Amd.1:2004. ISO 10140 consists of the following parts, under the general title Acoustics Laboratory measurement of sound insulation of building elements: Part 1: Application rules for specific products Part 2: Measurement of airborne sound ins

35、ulation Part 3: Measurement of impact sound insulation Part 4: Measurement procedures and requirements Part 5: Requirements for test facilities and equipment BS EN ISO 10140-1:2010+A1:2012 EN ISO 10140-1:2010+A1:2012 (E) ISO 2012Copyright European Committee for Standardization Provided by IHS under

36、license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-vIntroduction ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements (see Table 1). This part of ISO 10140 specifies the application rules for specific eleme

37、nts and products, including specific requirements for preparation, mounting, operating and test conditions. ISO 10140-2 and ISO 10140-3 contain the general procedures for airborne and impact sound insulation measurements, respectively, and refer to ISO 10140-4 and ISO 10140-5 where appropriate. For

38、elements and products without a specific application rule described in this part of ISO 10140, it is possible to apply ISO 10140-2 and ISO 10140-3. ISO 10140-4 contains basic measurement techniques and processes. ISO 10140-5 contains the requirements for test facilities and equipment. For the struct

39、ure of ISO 10140 (all parts), see Table 1. ISO 10140 (all parts) was created to improve the layout for laboratory measurements, ensure consistency and simplify future changes and additions regarding mounting conditions of test elements in laboratory and field measurements. It is intended for ISO 101

40、40 (all parts) to present a well-written and arranged format for laboratory measurements. It is intended to update this part of ISO 10140 with application rules for other products. It is also intended to incorporate ISO 140-18 into ISO 10140 (all parts). Annex J has been developed for joints filled

41、with fillers or seals. BS EN ISO 10140-1:2010+A1:2012 EN ISO 10140-1:2010+A1:2012 (E) ISO 2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-vi Table 1 Structure and contents of

42、 ISO 10140 (all parts) Relevant part of ISO 10140 Main purpose, contents and use Detailed content ISO 10140-1 It indicates the appropriate test procedure for elements and products. For certain types of element/product, it can contain additional and more specific instructions about quantities and tes

43、t element size and about preparation, mounting and operating conditions. Where no specific details are included, the general guidelines according to ISO 10140-2 and ISO 10140-3. Appropriate references to ISO 10140-2 and ISO 10140-3 and product-related, specific and additional instructions on: specif

44、ic quantities measured; size of test element; boundary and mounting conditions; conditioning, testing and operating conditions; additional specifics for test report. ISO 10140-2 It gives a complete procedure for airborne sound insulation measurements according to ISO 10140-4 and ISO 10140-5. For pro

45、ducts without specific application rules, it is sufficiently complete and general for the execution of measurements. However, for products with specific application rules, measurements are carried out according to ISO 10140-1, if available. Definitions of main quantities measured General mounting an

46、d boundary conditions General measurement procedure Data processing Test report (general points) ISO 10140-3 It gives a complete procedure for impact sound insulation measurements according to ISO 10140-4 and ISO 10140-5. For products without specific application rules, it is sufficiently complete a

47、nd general for the execution of measurements. However, for products with specific application rules, measurements are carried out according to ISO 10140-1, if available. Definitions of main quantities measured General mounting and boundary conditions General measurement procedure Data processing Tes

48、t report (general points) ISO 10140-4 It gives all the basic measurement techniques and processes for measurement according to ISO 10140-2 and ISO 10140-3 or facility qualifications according to ISO 10140-5. Much of the content is implemented in software. Definitions Frequency range Microphone positions SPL measurements Averaging, space and time Correction for background noise Reverberation time measurements Loss factor measurements Low-frequency measurements Radiated sound power by velocity measurement ISO 10140-5 It specifies all information needed to design, construct