EN ISO 9431-1999 en Construction Drawings - Spaces for Drawing and for Text and Title Blocks on Drawing Sheets《建筑工程制图 图样说明纸和标题栏的位置 ISO 9431-1990》.pdf

《EN ISO 9431-1999 en Construction Drawings - Spaces for Drawing and for Text and Title Blocks on Drawing Sheets《建筑工程制图 图样说明纸和标题栏的位置 ISO 9431-1990》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 9431-1999 en Construction Drawings - Spaces for Drawing and for Text and Title Blocks on Drawing Sheets《建筑工程制图 图样说明纸和标题栏的位置 ISO 9431-1990》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN IS0 9431-ENGL 1999 1111 lbZYbb9 0808q7 BRITISH STANDARD Construction drawings - Spaces for drawing and for text, and title blocks on drawing sheets ICs 01.100.30 435 m BS EN IS0 9431:1999 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN IS0 943L-ENGL

2、 1999 8 Lb2LibbS 0808472 371 been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 Amd. No. O BSI 10-1999 ISBN O 580 36114 9 BS EN IS0 9431:1999 Date Comments

3、 National foreword This British Standard reproduces verbatim IS0 9431:1990 and implements it as the UK national standard. This standard, together with BS EN IS0 4157-1:1999, BS EN IS0 8560: 1999 supersedes, BS 1192-1:1984 which is withdrawn. The UK participation in its preparation was entrusted by T

4、echnical Committee B/212, Tolerances, drawing practice, modular co-ordination, joints, project information and computer modelling, to Subcommittee B/212/2, Construction drawing practice, which has the responsibility to: BS EN IS0 4157-2: 1999, BS EN IS0 4157-3 1999, BS EN IS0 6284: 1999 and - aid en

5、quirers to understand the text; - present to the responsible intemationaVEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK A list of organization

6、s represented on this Subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entied “International Standards Cor

7、respondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ail the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does

8、not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreward page, the IS0 title page, page ii, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document indica

9、tes when the document was last issued. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 9431 July 1999 ICs 01.100.00 English version Construction drawings - Spaces for drawing and for text, and title blocks on drawing sheets (IS0 9431:1990) Dessins de construction - Zones rserves au dessin e

10、t au texte, et cartouches dinscription sur les feuilles de dessin (IS0 9431 : 1990) Zeichnungen fr das Bauwesen - Anordnung von Darste1lungen.Texten und Schriftfeldem auf Zeichnungsvordrucken (IS0 9431:1990) This European Standard was approved by CEN on 1 July 1999. CEN members are bound to comply w

11、ith the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secreta

12、riat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officia

13、l versions. CEN members are the national standards bodies of Austria. Belgium. Czech Republic, Denmark. Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMEE RIR STANDARDIZATION COMITE EURO

14、PEEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORMUNG Central Secretariat: rue de Stassart. 36 E1050 Brussels 8 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 9431:1999 E EN IS0 9431:1999 Foreword The text of the Internat

15、ional Standard from Technical Committee ISO/TC 10 “Technical drawings, product definition and related documentation“ of the Intemational Organization for Standardization (ISO) has been taken over as an European Standard by CENES. This European Standard shall be given the status of a national standar

16、d, either by publication of an identical text or by endorsement, at the latest by January 2000, and conflicting national standards shall be withdrawn at the latest by January 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are b

17、ound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the Intemational Standard IS0 9

18、431:1990 has been approved by CEN as a European Standard without any modification. STD*BSI BS EN IS0 943L-ENGL 1777 W LL24bb7 0808ii75 081 EN IS0 9431:1999 I N TE R NATI O NA L STA N DAR D 9431 First edition 1990-1 2-1 5 Construction drawings - Spaces for drawing and for text, and title blocks on dr

19、awing sheets Dessins de construction - Zones rserves au dessin et au texte, et cartouches dinscription sur les feuilles de dessin Reference number IS0 943 1 : 1990( E) Foreword IS0 (the International Organization for Slandardization) is a worldwide federation of national standards bodies (IS0 member

20、 bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical cornminee has been established has lhe right to be represented on that committee. International organizations, govern- ment

21、al and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Dran International Standards adopted by the technical committees are circulated to the membe

22、r bodies for voting. Publication as an Inter- national Standard requires approval by at least 75% of the member bodies casting a vote. International Standard IS0 9431 was prepared by Technical Committee ISO/TC IO, Technical drawings, product definition and related documen- tation. Annex A of this In

23、ternational Standard is for information only Descriptors: construction, drawings, technlcal drawings, spacing, title blocks. ii Construction drawings - Spaces for drawing and for text, and title blocks on drawing sheets 1 Scope This International Standard specifies requirements concerning the placin

24、g, layout and contents of spaces for drawing and for text, and title blocks on construction drawings. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editi

25、ons indicated were valid. All stan- dards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of ap- plying the most recent editions of the standards in- dicated below. Members of IEC and IS0 maintain registers of curr

26、ently valid International Standards. IS0 3098-1:1974, Technical drawings - Lettering - Part 1: Currently used characters. IS0 7200:1984, Technical drawings - Title blocks. 3 General layout (see figure 1 and figure 2) The space on a drawing sheet is primarily divided into - a space for drawing (see c

27、lause 4); - a space for text (see clause 5); - a title block (see IS0 7200). 4 Space for drawing The figures comprising a drawing shall be arranged .r horizontal rows and vertical columns. A main fig- ire, if one is identified as such, shall be placed at the top left of the drawing or at the top lef

28、 of a group of figures. If possible, consideration shall be taken of A4-size folds of a drawing sheet when figures are drawn. 5 Space for text 5.1 General The space for text on a drawing sheet shall contain all information necessary for the understanding of the contents of the drawing (see 5.2), exc

29、ept for the text which needs to be placed adjacent to the figures in the space for drawing. The space for text shall normally be placed at the right-hand edge of the drawing sheet (see figure I); the width of the space shall be equal to that of the title block, .e. maximum 170 mm, or at least 100 mm

30、. If a figure takes up the whole width of the drawing sheet, the space for text shall be placed at the bot- tom edge of the drawing sheet (see figure2); the height of the space shall be chosen as required. The space for text shall be divided into columns of ap- propriate width; if possible, account

31、shall be taken of folds in a folded drawing when deciding on col- umn width. 5.2 Information to be placed in space for text 5.2.1 General The following information is normally placed in the space for text: - explanations (see 5.2.2); - instructions (see 5.2.3); - references (see 5.2.4); - location f

32、igure (see 5.2.5); 1 STD-BSI BS EN IS0 9431-ENGL L979 lb24bb7 0808478 89T EN IS0 9431:1999 r - I - - revision table (see 5.2.6). - Space for drawlng Space for text (sec 5.1 tor /- dlmenslom) Tltle block 5.2.2 Explanations Under ?Explanations?, information shall be given which is needed to read the d

33、rawing, e.g. expla- nations of special symbols, designations, abbrevi- ations and units of dimensions. 5.2.3 Instructions Under ?Instructions?, information, supplementary to the information in the space for drawing, shall be given which is needed to perform what is shown on the drawing, e.g. instruc

34、tions relating to material, realization, surface treatment, assembly placing, number of units and combined dimensions. If several objects are shown on the drawing, general instructions shall be placed in the space for text and special instructions shall be placed adjacent to the relevant figures. -

35、details concerning the revision; - date of revision; - signature of person responsible for revision. The width of the revision table shall be equal to ei- ther a) the width of the title block, if the revision table is placed immediately above the title block, b) at least 100 mrn, if the revision tab

36、le is placed to the lefi of the title block. The height of each line in the revision table shall be in accordance with the rules given in IS0 3098-1 and shall meet the minimum requirement for spacing of base lines. An example of the layoiit of a revision table is illus- trated in figure6. 5.2.4 Refe

37、rences 5.3 Layout Under ?References?, reference shall be made to supplementary drawings and other documents. 5.2.5 Location figure A location figure shall be placed so that it remains visible after the drawing has been folded. A location figure shall comprise, as required, the following figures: - s

38、chematic site plan with area, arrow indicating the north, building, part of building, etc. marked (see figure 3); - schematic plan of building with area, part, etc. indicated (see figure 4); - schematic section through building with floor plan, direction of view, etc. indicated (see figure 5). 5.2.6

39、 Revision table A revision table shall be used to record all revisions such as corrections and/or amendments following the first issue. In addition, any other factor which might influence the validity of the drawing shall be recorded in the revision table. A revision table shall contain the followin

40、g infor- mation: Examples of the layout of the space for text on the drawing sheet are given in figure 7, figure8 and fig- ure 9. Figure 1 - Space for dfawlng Figure 2 - designations of revision and, if required, number of places where correction has been made; 2 II E A A - Ln Figure 3 DcsIgnatIan D

41、etona of revlsbn Dote Slgn. EN IS0 9431:1999 O O O O O O Figure 4 a 1 Figure 5 Dimensions in rnillimetrss Figure 6 3 EN IS0 9431:1999 I- -_ - Locntlon flgure - Tltle block I- - i - Explnnaflonr - Instructlons References - - Locntlon tlpurc - Revlslon table Title block - Flgure 7 Figure 8 I I Explana

42、tlorm Instructions References I I - I - Explnnntlons - Instructlons - References - Revlslon table - Locntlon flguc - Tltle Mock c- ul Figure 9 4 STD-BSI BS EN IS0 7931-ENGL 1799 Lb24bh9 08118481 389 EN IS0 9431:1999 Annex A (informative) Bibliography i J IS0 128:1982, Technical drawings - General pr

43、inciples of presentation. 2 IS0 5457:1980, Technical drawings - Sizes and layouf of drawing sheets. 3 J IS0 8048:1984, Technical drawings - Construction drawings - Representation of views, sections and cuts. 5 STD*BSI BS EN IS0 7431-ENGL 1777 m Zb24bb7 0808482 210 m BS EN IS0 9431:1999 BSI 389 Chisw

44、ick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are update

45、d by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British S

46、tandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lates

47、t editions of standards. Buying standards Orders for ail BSI, international and foreign standards publications should be addressed to Customer Services. Tel 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of thos

48、e that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information service

49、s are also available which give details on al its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in a BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.