EN ISO 7042-2012 en Prevailing torque type all-metal hexagon high nuts - Property classes 5 8 10 and 12《的转矩型全金属六角高坚果 房地产类5 8 10和12》.pdf

《EN ISO 7042-2012 en Prevailing torque type all-metal hexagon high nuts - Property classes 5 8 10 and 12《的转矩型全金属六角高坚果 房地产类5 8 10和12》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 7042-2012 en Prevailing torque type all-metal hexagon high nuts - Property classes 5 8 10 and 12《的转矩型全金属六角高坚果 房地产类5 8 10和12》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 7042:2012Prevailing torque type all-metal hexagon high nuts Property classes 5, 8, 10 and 12 BS EN ISO 7042:2012 BRITISH STANDARDNational forewordThis British Standard

2、is the UK implementation of EN ISO 7042:2012.It supersedes BS EN ISO 7042:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9, Fasteners.A list of organizations represented on this committee can beobtained on request to its secretary.This publica

3、tion does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 77983 1ICS 21.060.20Compliance with a British Standard cannot confer immunity fro

4、mlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7042 December 2012 ICS 21.060.20 Supersedes EN ISO

5、 7042:1997English Version Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012) crous hexagonaux hauts autofreins tout mtal - Classes de qualit 5, 8, 10 et 12 (ISO 7042:2012) Sechskantmuttern mit Klemmteil (Ganzmetallmuttern), Typ 2 - Festigkeitsklasse

6、n 5, 8, 10 und 12 (ISO 7042:2012) This European Standard was approved by CEN on 3 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-

7、date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translati

8、on under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, F

9、ormer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COM

10、IT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 7042:2012: EBS EN ISO 7042:2012EN ISO 7042:2012 (E) 3 Foreword

11、 This document (EN ISO 7042:2012) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of

12、an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be hel

13、d responsible for identifying any or all such patent rights. This document supersedes EN ISO 7042:1997. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croati

14、a, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

15、 United Kingdom. Endorsement notice The text of ISO 7042:2012 has been approved by CEN as a EN ISO 7042:2012 without any modification. BS EN ISO 7042:2012ISO 7042:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Dimensions . 24 Requirements and ref

16、erence International Standards 35 Designation . 3Bibliography . 4BS EN ISO 7042:2012ISO 7042:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally c

17、arried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wor

18、k. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare Interna

19、tional Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the e

20、lements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 7042 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with metric internal thread.This third edition cancels and rep

21、laces the second edition (ISO 7042:1997), of which it constitutes a minor revision.iv ISO 2012 All rights reservedBS EN ISO 7042:2012INTERNATIONAL STANDARD ISO 7042:2012(E)Prevailing torque type all-metal hexagon high nuts Property classes 5, 8, 10 and 121 ScopeThis International Standard specifies

22、the characteristics of prevailing torque type all-metal hexagon high nuts, with threads from M5 up to and including M36, in product grade A for threads up to and including M16 and product grade B for threads above M16, and with property classes 5, 8, 10 and 12.NOTE 1 The dimensions of the nuts with

23、the exception of the dimensions mwand hmaxcorrespond to those given in ISO 4033.NOTE 2 Nuts of property class 9 are dealt with in ISO 7720.If other specifications are required, they can be selected from existing International Standards, for example ISO 261, ISO 724, ISO 898-2, ISO 965-2, ISO 2320 an

24、d ISO 4759-1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 225, Fasteners Bolts, sc

25、rews, studs and nuts Symbols and descriptions of dimensionsISO 261, ISO general purpose metric screw threads General planISO 724, ISO general-purpose metric screw threads Basic dimensionsISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel Part 2: Nuts with specified pr

26、operty classes Coarse thread and fine pitch threadISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium qualityISO 2320, Prevailing torque type steel nuts Mechanical and performance propertiesISO 3269, Fa

27、steners Acceptance inspectionISO 4042, Fasteners Electroplated coatingsISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-2, Fasteners Surface discontinuities Part 2: NutsISO 8992, Fasteners General requirements for bolts, screws, studs and n

28、utsISO 10683, Fasteners Non-electrolytically applied zinc flake coatingsISO 10684, Fasteners Hot dip galvanized coatings ISO 2012 All rights reserved 1BS EN ISO 7042:2012ISO 7042:2012(E)3 DimensionsSee Figure 1 and Table 1Symbols and descriptions of dimensions are specified in ISO 225.aPrevailing to

29、rque element, shape at the discretion of the manufacturer.b = 15 to 30.c = 90 to 120.Figure 1Table 1 DimensionsDimensions in millimetresThread DM5 M6 M8 M10 M12 (M14)aM16 M20 M24 M30 M36Pb0,8 1 1,25 1,5 1,75 2 2 2,5 3 3,5 4damax. 5,75 6,75 8,75 10,80 13,00 15,10 17,30 21,60 25,90 32,40 38,90min. 5,0

30、0 6,00 8,00 10,00 12,00 14,00 16,00 20,00 24,00 30,00 36,00dwmin. 6,88 8,88 11,63 14,63 16,63 19,64 22,49 27,70 33,25 42,75 51,11e min. 8,79 11,05 14,38 17,77 20,03 23,36 26,75 32,95 39,55 50,85 60,79hmax. 5,10 6,00 8,00 10,00 13,30 14,10 16,40 20,30 23,90 30,00 36,00min. 4,80 5,40 7,14 8,94 11,57 1

31、3,40 15,70 19,00 22,60 27,30 33,10mwmin. 3,52 3,92 5,15 6,43 8,30 9,68 11,28 13,52 16,16 19,44 23,52smax. 8,00 10,00 13,00 16,00 18,00 21,00 24,00 30,00 36,00 46,00 55,00min. 7,78 9,78 12,73 15,73 17,73 20,67 23,67 29,16 35,00 45,00 53,80aThe size in parentheses should be avoided, if possible.bP is

32、the pitch of the thread.2 ISO 2012 All rights reservedBS EN ISO 7042:2012ISO 7042:2012(E)4 Requirements and reference International StandardsSee Table 2.Table 2 Requirements and reference International StandardsMaterial SteelGeneral requirements International Standard ISO 8992Thread Tolerance class

33、6HInternational Standards ISO 261, ISO 724, ISO 965-2Mechanical and performance propertiesProperty class 5, 8, 10, 12International Standards ISO 898-2, ISO 2320Tolerance Product grade For D M16: AFor D M16: BInternational Standard ISO 4759-1Finish CoatingAs processedRequirements for electroplating a

34、re specified in ISO 4042.Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683.Requirements for hot dip galvanizing are specified in ISO 10684.Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser.Surface i

35、ntegrity Limits for surface discontinuities are specified in ISO 6157-2.Acceptability Acceptance inspection is specified in ISO 3269.5 DesignationEXAMPLE A prevailing torque type all-metal hexagon high nut, with thread M12 and property class 8 is designated as follows:Prevailing torque type hexagon

36、high nut ISO 7042 - M12 - 8 ISO 2012 All rights reserved 3BS EN ISO 7042:2012ISO 7042:2012(E)Bibliography1 ISO 4033, Hexagon high nuts (style 2) Product grades A and B2 ISO 7720, Prevailing torque type all-metal hexagon nuts, style 2 Property class 94 ISO 2012 All rights reservedBS EN ISO 7042:2012T

37、his page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is

38、incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodi

39、cally updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

40、using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an indivi

41、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BS

42、I Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation

43、 of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept

44、up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards an

45、d PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity t

46、hat own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sys

47、tem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: