EN ISO 584-1997 en Plastics - Unsaturated Polyester Resins - Determination of Reactivity at 80 Degrees Celsius (Conventional Method)《塑料 不饱和聚酯数脂80℃时的反应性测定(常规方法)ISO 584-1982》.pdf

《EN ISO 584-1997 en Plastics - Unsaturated Polyester Resins - Determination of Reactivity at 80 Degrees Celsius (Conventional Method)《塑料 不饱和聚酯数脂80℃时的反应性测定(常规方法)ISO 584-1982》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 584-1997 en Plastics - Unsaturated Polyester Resins - Determination of Reactivity at 80 Degrees Celsius (Conventional Method)《塑料 不饱和聚酯数脂80℃时的反应性测定(常规方法)ISO 584-1982》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN IS0 584-ENGL 1778 Lb2LfbbS Ob72875 85T BRITISH STANDARD Plastics - Unsaturated polyester resins - Determination of reactivity at 80 “C (conventional method) The European Standard EN IS0 584 : 1997 has the status of a British Standard ICs 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCE

2、PT AS PERMITTED BY COPYRIGm LAW BS EN IS0 584 : 1998 STD-BSI BS EN IS0 58V-ENGL 1998 m 1b24bb7 Ob7287b 79b D BS EN IS0 584 : 1998 This British standard, hawig been prepared under the direction of the Sector Board for Materias and Chemicals, was pubiished under the authon of the Standards Board and c

3、omes into effect on 16 January 1998 National foreword This British Standard is the English language version of EN IS0 584 : 1997. It is identical with IS0 584 : 1982. The UK participation in its prepamtion was entrusted to Technical Committee PW42, Fibre reinforced thermosetting plastics and prepegs

4、, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible intematio - monitor related intedonal and European developments and promulgate them in the UK. A iist of organizationS represented on this committee can be obtained on request to its semtary. Cros

5、s-references Attention is drawn to the fact that CEN and CENELEC Standards normally inciude an annex which lists nomative references to intedonal publications with their corresponding European publications. The British standards which implement these in-onal or European publications may be found in

6、the BSI Standards Catalogue under the section entitled Intedonal Standards Correspondence Index, or by using the Fnd facility of the BSI Stan- Electronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises

7、a front cover, an inside hnt cover, the EN is0 titie page, the EN IS0 foreword page, the Is0 titie page, the IS0 foreword page, pages 1 to 3, a blank page, an inside back cover and a back cover. Amendments issued since publication ISBN O S 28897 8 STD-BSI BS EN IS0 584-ENGL 1778 m 1624bb7 b72877 b22

8、 = EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 584 November 1997 ICs 83.080.10 Descriptors: see IS0 document English version Plastics - Unsaturated polyester resins - Determination of reactivity at 80 OC (conventional method) (IS0 584:1982) Plastiques - Rsines de poiyesters non satur qu

9、antity and spatial parameters Of the test catalyst system (m/xtures of catalysts, combinations of catalysts and b) speed of heating the test portion placed in a accelerators). temperature controlled bath. For example, the replacement of water in the bath by another fluid with a lower heat capacity (

10、glycol, oil, etc.) leads to slower heating; 2 Principle c) type of temperature measuring dement Placed in the test portion and its ability to respond to rapid changes in temperature. Thermometers with a slow response and thermocouples with large junctions between the resistance leads are unsatisfact

11、ow; time. Placing of a mixture of 100 parts of resin with 1 part of catalyst in a test-tube of defined size. Heating of the test-tube and its contents in a water-bath at 80 OC for the duration of the reaction, and noting (or recording) the rise in temperature with dl accurate centring of the thermoc

12、ouple in the test portion, both in height and in line with the axis. 3 Reagent During the analysis, use only reagents of recognized analytical grade. These conditions which are mandatory are specified in the text of this International Standard. Benzoyl peroxide, catalyst. 1 This International Standa

13、rd specifies a method for the deter- mination of the reactivity of unsaturated polyester resins as characterized by the maximum temperature reached by a soh- tion of unsaturated polyester resin and catalyst when heated in a water-bath at 80 OC, by the time taken for the temperature of Scope and fiel

14、d of application WARNING - Attention is drawn to the dangers involved in handling pure benzoyl peroxide. A mixture of 50 % (rnlrn) of benzoyl peroxide catalyst in dibutyl phthalate having an active oxygen content between 3,26 and 3.33 % (rn/rn), as measured by known analytical methods. 1 STD-BSI BS

15、EN IS0 589-ENGL 2978 m Lb2qbbS b72882 T9T W EN IS0 684 : 1997 4 Apparatus 4.1 with a thermostat and a circulation pump or stirrer. Water-bath.1) maintained at 80 f 0,5 OC and provided 4.2 Test-tube, of borosilicate glass or any other glass giving the same results, of internal diameter 18 f 1 mm, len

16、gth 210 f 5 mm and wall thickness 1 i 0,2 mm. 4.3 Iron-constantan thermocouple, consisting of wires of 1 f 0,05mm thickness, with a welded junction of 2mm diameter maximum and a meter for measuring temperatures up to 250 OC, graduated in divisions of 2 OC. NOTE - It is desirable to use screened ther

17、mocouples that can be positioned centrally. 4.4 If available a recorder, permitting the readings of temperature on the graph paper to the nearest 1 OC and the time to the nearest 15 8. 4.5 Device, for locating the thermocouple centrally in the test-tube (see the figure). 4.6 Balance, accurate to 0,O

18、l g. 4.7 Stop watch. 5 Procedure 6.1 Weigh 2 i 0.01 g of the benzoyl peroxide-dibutyl phthalate mixture (ciause3) into a glass beaker of capacity 250 ml and add 100 i 1 g of resin at a temperature between 15 and 30 OC. Continue stirring for 2 to 3 min. 6.2 Then immedietely pour part of the mixture i

19、nto the test- tube (4.21 to a height of 7 to 8 cm. Introduce the thermocouple into the mixture in a position on the axis of the tube and equidistant from the bottom and the surface of the mixture (see the figure). Then piace the tube in the wter-bath at 80 i 0,5 OC, so that the surface of the resin

20、is weil beneath the level of the surface of the water. 5.3 If a recorder is used, start and allow the recorder to run during the complete reaction. Alternatively, note the maximum temperature reached, as well as the time taken for the temperature of the mixture, determined by the thermocouple, to ri

21、se from 65 OC to the maximum temperature, and in the case where this temperature is greater than 90 OC, the time to rise from 65 to 90 OC. 5.4 Repeat the test, beginning at 5.1, until two consecutive determinations do not differ by more than 5 OC in temperature and 10 % in time. 6 Test report The te

22、st report shall include the following information : a) a reference to this International Standard; bl a complete identification of the resin tested; c) the type of thermocouple used and whether screened or unscreened; d) the individual values of the maximum temperature reached in the two tests and t

23、he average value; e) the individual values of the time taken for the tempera- ture to rise from 65 OC to the maximum temperature in the two tests and the average value; f) if the maximum temperature is above 90 OC, the in- dividual values of the time taken for the temperature to rise from 65 to 90 O

24、C in the two tests and the average value; g) if a recorder is used, the graphs giving the temperature plotted against time. h) any deviations from the standard test conditions speci- fied in this International Standard, for example type and temperature of the heating medium, catalyst system used, th

25、ermocouple system used, etc. (see note 2 to clause i). II The water in the bath may be replaced by another fluid agreed upon by the interested parties. 2 STD.BSI BS EN IS0 5Li-ENGL 1998 lb24bb9 b72883 92b EN IS0 584 : 1997 I I l- L. A- + / I I I II 3 17 ! 22 Section A-A Dimensions in millimetres Ope

26、ning for thermocouple 1A Figure - Example of device for locating the thermocouple centrally in the test-tube 1) The leveis for the test mixture and the thermocouple shall be in accordance with the instructions in 5.2. 3 BS EN IS0 584 : 1998 BSI 389 Chiswick High Road London w4 4AL 3SI - British Stan

27、dards Institution IS1 is the independent national body responsible for preparing British Standards. It resents the UK view on standards in Europe and at the international level. It is icorporated by Royal Charter. :ontract requirements British Standard does not purport to include ali the necessary p

28、rovisions of a ontract. Users of Brish Standards are responsible for their correct application. levisions Iritish Standards are updated by amendment or revision. Users of British Standards houid make sure that they possess the latest amendments or editions. t is the constant aim of BSI to improve th

29、e quality of our products and services. We vould be grateful if anyone finding an inaccuracy or ambiguity while using this !ritish Standard would inform the Secretary of the responsible technical committee, he identity of which can be found on the inside front cover. Tel O181 996 9000; Fax: I181 996

30、 7400. 3SI offers members an individual updating service called PLUS which ensures that iubscribers automatically receive the latest editions of standards. 3uying standards Irders for all BSI, international and foreign standards publications should be Iddressed to Customer Services, Sales Department

31、 at Chiswick Tel 0181 996 7000; Tax: O81 996 7001. n response to orders for international standards, it is BSI policy to supply the BSI mplementation of those that have been published as British Standards, unless Itherwise requested. nformation on standards 3SI provides a wide range of information o

32、n national, European and international ;tandards through its Library, the Standardline Database, the BSI Information echnology Service (BITS) and its Technical Help to Exporters Service. Contact the nformation Department at Chiswick Tel O181 996 7111; Fax: O181 996 7048. Subscribing members of BSI a

33、re kept up to date with standards developments and -eceive substantkd discounts on the purchase price of standards. For details of hese and other benefits contact Customer Services, Membership at Chiswick lel 0181 996 7002; Fax: O181 996 7001. Copyright Copyright subsists in all BSI publications. BS

34、I also hols the copyright, in the UK, of he publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying

35、, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copynght Manager, BSI, 389 Chiswick High Road, London W4 4AL