EN ISO 5674-2009 en Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria《农业和林业用拖拉机和机.pdf

《EN ISO 5674-2009 en Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria《农业和林业用拖拉机和机.pdf》由会员分享，可在线阅读，更多相关《EN ISO 5674-2009 en Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria《农业和林业用拖拉机和机.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO5674:2009ICS 65.060.01NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTractors andmachinery foragriculture andforestry Guardsfor power take-off(PTO) drive-shafts Strength and weartests and acceptancecriteria (ISO 5674:2004,corrected version2005-07-01)Th

2、is British Standardwas published underthe authority of theStandards Policy andStrategy Committee on 30September 2009 BSI 2009ISBN 978 0 580 64626 3Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 5674:2009National forewordThis British Standard is the UK implementation of EN ISO 5

3、674:2009. Itis identical to ISO 5674:2004. It supersedes BS EN ISO 5674:2006 whichis withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AGE/6, Agricultural tractors and forestry machinery.A list of organizations represented on this committee can be obtained onreque

4、st to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 5674

5、February 2009 ICS 65.060.01 Supersedes EN ISO 5674:2006English Version Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria (ISO 5674:2004, corrected version 2005-07-01) Tracteurs et matriels agricoles et

6、 forestiers - Protecteurs darbres de transmission cardans de prise de force - Essais de rsistance mcanique et dusure et critres dacceptation (ISO 5674:2004, version corrige 2005-07-01) Traktoren und land- und forstwirtschaftliche Maschinen - Schutzeinrichtungen fr Gelenkwellen - Festigkeits- und Ver

7、schleiprfungen und Annahmekriterien (ISO 5674:2004, korrigierte Fassung 2005-07-01) This European Standard was approved by CEN on 26 January 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

8、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A versi

9、on in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den

10、mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS

11、ATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5674:2009: EBS EN ISO 5674:2009EN ISO 5674:2009 (E) 3 Foreword The text of ISO 5674:

12、2004, corrected version 2005-07-01 has been prepared by Technical Committee ISO/TC 23 “Tractors and machinery for agriculture and forestry” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 5674:2009 by Technical Committee CEN/TC 144 “Tractors and machiner

13、y for agriculture and forestry” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the

14、 latest by December 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 5674:2006. This document has

15、 been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directives. For relationship with EC Directives, see informative Annex ZA and ZB, which are integral parts of this document. According to the CEN/

16、CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

17、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 5674:2004, corrected version 2005-07-01 has been approved by CEN as a EN ISO 5674:2009 without any modification. BS EN ISO 5674:2

18、009EN ISO 5674:2009 (E) 4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC This International Standard has been prepared under a mandate given to CEN by the European Commission and the European F

19、ree Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/79/EC. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State,

20、compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with Essential Requirements 1.3.2 first, second and fourth paragraph, 1.3.7 first paragraph, 1.4.1 first and second indent, 1.4.2.1 first paragraph, 1.5.11 rel

21、ated to UV radiation, 3.4.2 and 3.4.7 sixth paragraph of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ BS EN ISO 5674:2009EN ISO 5674:2009 (E) 5 Annex ZB (informative)

22、 Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This International Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requireme

23、nts of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers

24、, within the limits of the scope of this standard, a presumption of conformity with Essential Requirements 1.3.2 first, second and fourth paragraph, 1.3.7 first paragraph, 1.4.1 first, second and third indent of first paragraph and second paragraph, 1.5.11 related to UV radiation, and 3.4.7 seventh

25、paragraph of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 5674:2009ISO 5674:2004(E) ISO 2004 All rights reserved iiiContents Page Foreword iv Introduction v

26、1 Scope 1 2 Normative references 1 3 Terms and definitions .1 4 General test conditions.2 4.1 Guard 2 4.2 Other .2 5 Test equipment 2 5.1 General2 5.2 Test parameters .2 6 Tests4 6.1 General4 6.2 Wear test.4 6.3 Bearing corrosion test (Perform only if the guard has bearings running in contact with t

27、he PTO-shaft) .4 6.4 Strength tests.5 6.5 Tests at sub-zero temperature .8 6.6 Restraining means test at ambient temperature 10 7 Final acceptance criteria.11 8 Test report 12 Annex A (normative) Test schedule 13 Annex B (normative) UV test for plastic guards 16 Annex C (informative) Typical test re

28、port.17 Annex D (informative) Novel design guard and restraining systems tests.20 BS EN ISO 5674:2009ISO 5674:2004(E) iv ISO 2004 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

29、of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-government

30、al, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The mai

31、n task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Att

32、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5674 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and fores

33、try, Subcommittee SC 2, Common tests. This second edition of ISO 5674 cancels and replaces the first editions of ISO 5674-1:1992 and ISO 5674-2:1992, of which it constitutes a technical revision. This corrected version of ISO 5674:2004 incorporates the following corrections or modifications. An erro

34、r in the second column heading of Table 2 (“m/m”) has been eliminated. Figure 1 has been modified, and numbering of elements and a key added. The wording of the third sentence of 6.5.2 has been changed. The title of 6.6 has been corrected from “specified temperature” to “ambient temperature”. The sy

35、stem of numbering and the wording of A.1 has been altered to avoid possible confusion. Figure A.1 has been changed to show the blows at three locations, and “h” has been deleted from the drawing and the legend as a result of the change to 6.5.2. Cross-references have been added to the legend to Figu

36、re D.1. The system of numbering and the wording of D.9 has been altered to avoid possible confusion. BS EN ISO 5674:2009ISO 5674:2004(E) ISO 2004 All rights reserved vIntroduction This document is a type C standard as stated in ISO 12100. The machinery concerned and the extent to which hazards, haza

37、rdous situations and events are covered are indicated in the scope of this standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for mach

38、ines that have been designed and built according to the provisions of this type C standard. BS EN ISO 5674:2009BS EN ISO 5674:2009INTERNATIONAL STANDARD ISO 5674:2004(E) ISO 2004 All rights reserved 1Tractors and machinery for agriculture and forestry Guards for power take-off (PTO) drive-shafts Str

39、ength and wear tests and acceptance criteria 1 Scope This International Standard specifies laboratory tests for determining the strength and wear resistance of guards for power take-off (PTO) drive-shafts on tractors and machinery used in agriculture and forestry, and their acceptance criteria. It i

40、s intended to be used in combination with ISO 5673. It is applicable to the testing of PTO drive-shaft guards and their restraining means. It is not applicable to the testing of guards designed and constructed to be used as steps. 2 Normative references The following referenced documents are indispe

41、nsable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in co

42、lour ISO 500 (all parts), Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 ISO 4892-1, Plastics Methods of exposure to laboratory light sources Part 1: General guidance ISO 4892-2, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc sources ISO 5673-1, Agricu

43、ltural tractors and machinery Power take-off drive shafts and power-input connection Part 1: General, manufacturing and safety requirements ISO 5673-2, Agricultural tractors and machinery Power take-off drive shafts and power-input connection Part 2: Specification for use of PTO drive shafts, and po

44、sition and clearance of PTO drive line and PIC for various attachments 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5673-1 and the following apply. 3.1 ambient temperature any temperature between 5 C and 35 C BS EN ISO 5674:2009ISO 5674:2004(E) 2

45、ISO 2004 All rights reserved4 General test conditions 4.1 Guard 4.1.1 The guard shall be representative of a production model and be within the tolerances specified for the guard. The results obtained from the sample can be used to certify guards of shorter or longer lengths, provided the basic desi

46、gn remains the same. When a guard is designed for use with several drive-shaft types, a representative selection of shaft and guard combinations shall be tested. 4.1.2 If the guard is made of plastic material (or any other material susceptible to degradation by UV radiation), it shall be certified b

47、y the manufacturer to be resistant to degradation from UV radiation under an appropriate, recognized method. See Annex B for an example. 4.1.3 During testing, all operating and maintenance instructions specified for the shaft and guard shall be complied with, except where specifically mentioned by t

48、his International Standard. 4.1.4 The guard shall be tested in conjunction with a PTO drive-shaft of between 900 mm and 1 010 mm closed length for which it is intended. The same guard shall be used throughout all the tests. 4.2 Other 4.2.1 Where specified in this International Standard that the PTO

49、drive-shaft shall be revolving, its rotational frequency shall be 1 000 r/min. 4.2.2 All tests shall be carried out in accordance with the schedule and in the sequence given in Annex A. 5 Test equipment 5.1 General 5.1.1 Wear test equipment, which shall be capable of holding the PTO drive-shaft and revolving it at a frequency of 1 000 r/min. The shafts and guards shall be mounted as specified for operational use and only fixed by their designated restraining device. The fixing points shall be in accor