EN ISO 4029-2003 en Hexagon socket set screws with cup point《内六角圆柱端紧定螺钉 ISO 4029-2003》.pdf

《EN ISO 4029-2003 en Hexagon socket set screws with cup point《内六角圆柱端紧定螺钉 ISO 4029-2003》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 4029-2003 en Hexagon socket set screws with cup point《内六角圆柱端紧定螺钉 ISO 4029-2003》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 4029:2003 Incorporating Corrigendum No.1 Hexagon socket set screws with cup point The European Standard EN ISO 4029:2003 has the status of a British Standard ICS 21.060.10 BS EN ISO 4029:2003 This British Standard was published under the authority of the Standards Policy a

2、nd Strategy Committee on 23 December 2003 BSI 5 April 2004 ISBN 0 580 43187 8 National foreword This British Standard is the official English language version of EN ISO 4029:2003. It is identical with ISO 4029:2003. It supersedes BS 4168-5:1994 which is withdrawn. The UK participation in its prepara

3、tion was entrusted by Technical Committee FME/9, Nuts, bolts and accessories, to Subcommittee FME/9/8, Hexagon socket screws, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards

4、which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publ

5、ication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internatio

6、nal/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO ti

7、tle page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 15067

8、Corrigendum No.1 5 April 2004 Corrected EN ISO foreword and incorporation of Annex ZA.EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO4029 December2003 ICS21.060.10 Englishversion Hexagonsocketsetscrewswithcuppoint(ISO4029:2003) Vissansttesixpanscreux,boutcuvette(ISO 4029:2003) GewindestiftemitI

9、nnensechskantmitRingschneide(ISO 4029:2003) ThisEuropeanStandardwasapprovedbyCENon4November2003. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalre

10、ferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManageme

11、ntCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,SwitzerlandandUn ited Kingdom. EUROPEANCOMMI

12、TTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2003CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO4029:2003EINESO04:9202(30E) 2 CORRECTED20040303 Foreword Thisdocumen

13、t(ENISO4029:2003)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandnon threadedmechanicalfastenersandaccessories“,thesecretariatofwhichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anident

14、icaltextorbyendorsement,atthelatestbyJune2004,andconflictingnational standardsshallbewithdrawnatthelatestbyJune2004. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Fi

15、nland,France,Germany,Greece,Hungary,Iceland,Ireland,Italy, Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,Switzerlandand theUnitedKingdom. Endorsementnotice ThetextofISO4029:2003hasbeenapprovedbyCENasENISO4029:2003withoutany modifications. NOTENormativereferencestoInternationalSt

16、andardsarelistedinAnnexZA(normative). ENISO4029:2003INTERNATIONAL STANDARD ISO 4029 Third edition 2003-12-01 Reference number ISO 4029:2003(E) Hexagon socket set screws with cup point Vis sans tte six pans creux, bout cuvetteENISO4029:2003ISO :9204(3002)E ii id FDPscalimer ThFDP si fam eliy ctnome n

17、iat deddebyepfa.sec In cacnadrociw eth sebodA sneciliycilop gn, thf siam elirp eb ytnide or viewb detu llahs ton tide ebed lnuet sst ehyfepcaa hcihw serdebme et desnecil era dedo tsni dnat no dellahpmoc eturep reformign ttide ehign. In odt gnidaolnwhsi liferap ,ticca setpe trehnie snopser ehtibtiliy

18、 fo not fnirA gnigniycilop gnisnecil sebod. Teh SItneC Olar Seerctraiat catpecs ibail ontily t nih.aera si Aebod t a sirramedak fo AsyS ebodtmeI snocrropta.de teDalis fo tfos ehtwcudorp erats t desuo taerct ehsi FDP fb nac elie ft ni dnuoG ehreneI lanfo relative to tf eh;eli tP ehDF-rctaenoi temarap

19、tpo erew sremizif deorp rinti.gn Evrey t neeb sah eracakt neo rusnee ttah tf ehtius si elibaf elosu re by ISO memdob rebsei. In eht kilnuyle evtne ttah a borplem retalit gno it si f,dnuo esaelp inform thtneC eral ceSrteraiat ta teh sserdda vigoleb new. IOS 3002 Alr lithgs reresv.de sselnU toesiwreh

20、sficep,dei rap ont fo thbup silitaciam nocudorper eb yde or tuilidez na nif yorm ro by nam ysnae, tcelerm ro cinoecinahcal, tohp gnidulcnicopom dna gniyicrfomli, tiwuoht repsimsi noin wrtif gnirtie mohI reSO ta the asserdd ebwol or ISOmem sreb obyd t nitnuoc ehry fo teh euqertsre. SIc Oopyright ofif

21、ce saCe soptael 65 -HCG 1121eneva 02 Te.l 22 14 + 10 947 11 Fax + 22 14 0 9479 74 Eam-il ocpyrithgios.ogr Web wwwi.soo.rg Pubni dehsil Stiwrezldna ENISO4029:2003 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b

22、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a

23、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives

24、, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies ca

25、sting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 4029 was prepared by Technical Committee ISO/TC 2, Fasteners. This third edition ca

26、ncels and replaces the second edition (ISO 4029:1993), which has been technically revised. ENISO4029:2003. vi 1 Hexagon socket set screws with cup point 1S c o p e This International Standard specifies the characteristics of hexagon socket set screws with cup point and threads from M1,6 up to and in

27、cluding M24 and of product grade A. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e.g. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3 and ISO 4759-1. 2 Normative references The follo

28、wing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols a

29、nd designations of dimensions ISO 261, ISO general-purpose metric screw threads General plan ISO 898-5, Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners not under tensile stresses ISO 965-2, ISO general purpose metric screw thr

30、eads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 3269, Fasteners Acceptance inspection ISO 3506-3, Mechanical propertie

31、s of corrosion-resistant stainless-steel fasteners Part 3: Set screws and similar fasteners not under tensile stress ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontin

32、uities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flak

33、e coatings ISO 23429, Gauging of hexagon sockets ENISO4029:2003ISO :9204(3002)E 2 3 Dimensions See Figure 1 and Table 1. Symbols and designations of dimensions are specified in ISO 225. Permissible alternative form of socket For broached sockets which are at the maximum limit of size, the overcut re

34、sulting from drilling shall not exceed of the length of any flat of the socket which is . a The angle is a requirement for short-length screws of nominal length, , situated in the shaded areas in Table 1. b The angle applies only to the portion of the point situated below the root diameter of the th

35、read. c Incomplete thread . d A slight rounding or countersink at the mouth of the socket is permissible. Figure 1 1/3 e/2 120 l 45 u2P 3002:9204OSINEENISO4029:2003 3 Table 1 Dimensions Dimensions in millimetres Thread ( ) M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10 M12 M16 M20 M24 a 0,35 0,4 0,45 0,5 0,7 0,8 1

36、 1,25 1,5 1,75 2 2,5 3 max. 0,80 1,00 1,20 1,40 2,00 2,50 3,00 5,0 6,0 8,00 10,00 14,00 16,00 min. 0,55 0,75 0,95 1,15 1,75 2,25 2,75 4,7 5,7 7,64 9,64 13,57 15,57 min. Minor thread diameter b, c min. 0,809 1,011 1,454 1,733 2,303 2,873 3,443 4,583 5,723 6,863 9,149 11,429 13,716 c n o m .0 , 70 , 9

37、1 , 31 , 522 , 5345681 01 2 max. 0,724 0,913 1,300 1,58 2,08 2,58 3,08 4,095 5,14 6,14 8,175 10,175 12,212 min. 0,710 0,887 1,275 1,52 2,02 2,52 3,02 4,020 5,02 6,02 8,025 10,025 12,032 min. d 0,7 0,8 1,2 1,2 1,5 2 2 3 4 4,8 6,4 8 10 e 1,5 1,7 2 2 2,5 3 3,5 5 6 8 10 12 15 Approximate mass, in kilogr

38、ams per 1 000 pieces ( ) (for information only) nom. min. max. 2 1,8 2,2 0,019 0,0292,5 2,3 2,7 0,025 0,037 0,063 3 2,8 3,2 0,029 0,044 0,075 0,1 4 3,76 4,24 0,037 0,059 0,1 0,14 0,23 5 4,76 5,24 0,046 0,074 0,125 0,18 0,305 0,42 6 5,76 6,24 0,054 0,089 0,15 0,22 0,38 0,54 0,74 8 7,71 8,29 0,07 0,11

39、9 0,199 0,3 0,53 0,78 1,09 1,88 10 9,71 10,29 0,148 0,249 0,38 0,68 1,02 1,44 2,51 3,72 12 11,65 12,35 0,299 0,46 0,83 1,26 1,79 3,14 4,73 6,7 16 15,65 16,35 0,62 1,13 1,74 2,49 4,4 6,73 9,5 15,7 20 19,58 20,42 1,4 2,22 3,19 5,66 8,72 12,3 20,9 31,1 25 24,58 25,42 2,82 4,07 7,24 11,2 15,8 27,4 41,4

40、55,2 30 29,58 30,42 4,94 8,81 13,7 19,3 33,9 51,7 70,3 35 34,5 35,5 10,4 16,2 22,7 40,4 62 85,3 40 39,5 40,5 12 18,7 26,2 46,9 72,3 100 45 44,5 45,5 21,2 29,7 53,3 82,6 115 50 49,5 50,5 23,6 33,2 59,8 92,6 130 55 54,4 55,6 36,6 66,3 103 145 60 59,4 60,6 40,1 72,8 114 160 NOTE Commercial lengths are

41、those between the bold stepped lines. ais the pitch of the thread. b . c Combined gauging of socket dimensions and , see ISO 23429. d For screws with nominal lengths in the shaded areas. e For screws with nominal lengths below the shaded areas. d P d z d f e s t l = 7,85 kg/dm 3 P e min = 1,14 s min

42、 es ENISO4029:20034 4 Requirements and reference International Standards See Table 2. 5 Designation EXAMPLE A hexagon socket set screw with cup point, thread M6, nominal length and of property class 45H, is designated as follows: Hexagon socket set screw ISO 4029 - M6 12 - 45H Table 2 Specifications

43、 and reference International Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard ISO 8992 Thread To l e r a n c e International Standards ISO 261, ISO 965-2, ISO 965-3 Mechanical properties Property class 45H A1-12H, A2-21H, A3-21H, A4-21H, A5-21H A

44、s agreed International Standards ISO 898-5 ISO 3506-3 ISO 8839 Tolerances Product grade A International Standard ISO 4759-1 Finish As processed Plain Plain Requirements for electroplating are covered in ISO 4042. Requirements for electroplating are covered in ISO 4042. Requirements for non-electroly

45、tically applied zinc flake coatings are covered in ISO 10683. Surface discontinuities Limits for surface discontinuities are covered in ISO 6157-1. Acceptability For acceptance procedure, see ISO 3269. 6g l= 12 mm ENISO4029:2003INESO04:9202(30E) 3 AnnexZA (normative) Normativereferencestointernation

46、alpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof

47、anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.Forundatedreferencesthelatesteditionofthepublicationreferredto applies(includingamendments). NOTEWhereanInternationalPublicationhasbeenmodifiedbycommonmodifications,indicated by(mod.),therelevantEN/HDapplies. Publication Year Title EN Year ISO225 1983 FastenersBolts,screws,studsand nutsSymbolsanddesignationsof dimensions EN20225 1991 ISO8985 1998 Mechanicalpropertiesoffasteners madeofcarbonsteelandalloysteel Part5:Setscrewsan