EN ISO 4016-2011 en Hexagon head bolts - Product grade C《六角头螺栓 产品等级C级》.pdf

《EN ISO 4016-2011 en Hexagon head bolts - Product grade C《六角头螺栓 产品等级C级》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 4016-2011 en Hexagon head bolts - Product grade C《六角头螺栓 产品等级C级》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 4016:2011Hexagon head bolts Productgrade C (ISO 4016:2011)BS EN ISO 4016:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO

2、4016:2011. It supersedes BS EN ISO 4016:2001 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does

3、not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 71150 3 ICS 21.060.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority

4、of the Standards Policy and Strategy Committee on 31 March 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4016 March 2011 ICS 21.060.10 Supersedes EN ISO 4016:2000English Version Hexagon head bolts - Product grade C (ISO 4

5、016:2011) Vis tte hexagonale partiellement filetes - Grade C (ISO 4016:2011) Sechskantschrauben mit Schaft - Produktklasse C (ISO 4016:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co

6、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exi

7、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national st

8、andards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland an

9、d United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 40

10、16:2011: EBS EN ISO 4016:2011EN ISO 4016:2011 (E) 3 Foreword This document (EN ISO 4016:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given

11、the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document ma

12、y be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4016:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound t

13、o implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed

14、en, Switzerland and the United Kingdom. Endorsement notice The text of ISO 4016:2011 has been approved by CEN as a EN ISO 4016:2011 without any modification. BS EN ISO 4016:2011ISO 4016:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a wor

15、ldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on

16、 that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted

17、in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standar

18、d requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 4016 was prepared by Te

19、chnical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This fourth edition cancels and replaces the third edition (ISO 4016:1999), of which it constitutes a minor revision. BS EN ISO 4016:2011ISO 4016:2011(E) iv ISO 2011 All rights reservedIntroduction This Inter

20、national Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032,

21、 ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12

22、125, ISO 12126 and ISO 21670). BS EN ISO 4016:2011INTERNATIONAL STANDARD ISO 4016:2011(E) ISO 2011 All rights reserved 1Hexagon head bolts Product grade C 1 Scope This International Standard specifies the characteristics of hexagon head bolts with threads from M5 up to and including M64, of product

23、grade C. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1 and ISO 4759-1. 2 Normative references The following referenced documents

24、are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensi

25、ons ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-1, ISO general-purpose metric screw th

26、reads Tolerances Part 1: Principles and basic data ISO 3269, Fasteners Acceptance inspection ISO 4018, Hexagon head screws Product grade C ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 8992, Fastene

27、rs General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings 3 Dimensions See Figure 1 and Tables 1 and 2. Symbols and descriptions of dimensions are specified in ISO 225. BS EN ISO 4016:2011ISO 4016:2011(E) 2 ISO 2011 All rights res

28、ervedDimensions in millimetres a = 15 to 30. b End without special requirements. c Incomplete thread u u 2P. d Reference datum for dw. eWasher face permissible. Figure 1 BS EN ISO 4016:2011ISO 4016:2011(E) ISO 2011 All rights reserved 3Table 1 Preferred threads Dimensions in millimetres Thread, d M5

29、 M6 M8 M10 M12 M16 M20 Pa0,8 1 1,25 1,5 1,75 2 2,5 b16 18 22 26 30 38 46 c22 24 28 32 36 44 52 b ref. d35 37 41 45 49 57 65 c max. 0,5 0,5 0,6 0,6 0,6 0,8 0,8 damax. 6 7,2 10,2 12,2 14,7 18,7 24,4 max. 5,48 6,48 8,58 10,58 12,7 16,7 20,84 dsmin. 4,52 5,52 7,42 9,42 11,3 15,3 19,16 dwmin. 6,74 8,74 1

30、1,47 14,47 16,47 22 27,7 e min. 8,63 10,89 14,2 17,59 19,85 26,17 32,95 nom. 3,5 4 5,3 6,4 7,5 10 12,5 max. 3,875 4,375 5,675 6,85 7,95 10,75 13,4 k min. 3,125 3,625 4,925 5,95 7,05 9,25 11,6 kwemin. 2,19 2,54 3,45 4,17 4,94 6,48 8,12 r min. 0,2 0,25 0,4 0,4 0,6 0,6 0,8 nom. = max. 8,00 10,00 13,00

31、16,00 18,00 24,00 30,00 s min. 7,64 9,64 12,57 15,57 17,57 23,16 29,16 l lsand lgflslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.25 23,95 26,05 5 9 30 28,95 31,05 10 14 7 12 35 33,75 36,25 15 19 12 17 For sizes above the solid, bold, s

32、tepped line, ISO 4018 is recommended. 40 38,75 41,25 20 24 17 22 11,75 18 45 43,75 46,25 25 29 22 27 16,75 23 11,5 19 50 48,75 51,25 30 34 27 32 21,75 28 16,5 24 55 53,5 56,5 32 37 26,75 33 21,5 29 16,25 25 60 58,5 61,5 37 42 31,75 38 26,5 34 21,25 30 65 63,5 66,5 36,75 43 31,5 39 26,25 35 17 27 70

33、68,5 71,5 41,75 48 36,5 44 31,25 40 22 32 80 78,5 81,5 51,75 58 46,5 54 41,25 50 32 42 21,5 34 90 88,25 91,75 56,5 64 51,25 60 42 52 31,5 44 100 98,25 101,75 66,5 74 61,25 70 52 62 41,5 54 110 108,25 111,75 71,25 80 62 72 51,5 64 120 118,25 121,75 81,25 90 72 82 61,5 74 130 128 132 76 86 65,5 78 140

34、 138 142 86 96 75,5 88 150 148 152 96 106 85,5 98 160 156 164 106 116 95,5 108 180 176 184 115,5 128 200 195,4 204,6 135,5 148 220 215,4 224,6 240 235,4 244,6 260 254,8 265,2 280 274,8 285,2 300 294,8 305,2 320 314,3 325,7 340 334,3 345,7 360 354,3 365,7 380 374,3 385,7 400 394,3 405,7 420 413,7 426

35、,3 440 433,7 446,3 460 453,7 466,3 480 473,7 486,3 500 493,7 506,3 BS EN ISO 4016:2011ISO 4016:2011(E) 4 ISO 2011 All rights reservedTable 1 (continued) Dimensions in millimetres Thread, d M24 M30 M36 M42 M48 M56 M64 Pa3 3,5 4 4,5 5 5,5 6 b 54 66 c 60 72 84 96 108 b ref. d 73 85 97 109 121 137 153 c

36、 max. 0,8 0,8 0,8 1 1 1 1 damax. 28,4 35,4 42,4 48,6 56,6 67 75 max. 24,84 30,84 37 43 49 57,2 65,2 dsmin. 23,16 29,16 35 41 47 54,8 62,8 dwmin. 33,25 42,75 51,11 59,95 69,45 78,66 88,16 e min. 39,55 50,85 60,79 71,3 82,6 93,56 104,86 nom. 15 18,7 22,5 26 30 35 40 max. 15,9 19,75 23,55 27,05 31,05 3

37、6,25 41,25 k min. 14,1 17,65 21,45 24,95 28,95 33,75 38,75 kwemin. 9,87 12,36 15,02 17,47 20,27 23,63 27,13 r min. 0,8 1 1 1,2 1,6 2 2 nom. = max. 36 46 55,0 65,0 75,0 85,0 95,0 s min. 35 45 53,8 63,1 73,1 82,8 92,8 l lsand lgflslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max.

38、min. max. min. max. min. max. min. max.25 23,95 26,05 30 28,95 31,05 For sizes above the solid, bold, stepped line, ISO 4018 is recommended. 35 33,75 36,25 40 38,75 41,25 45 43,75 46,25 50 48,75 51,25 55 53,5 56,5 60 58,5 61,5 65 63,5 6,5 70 68,5 71,5 80 78,5 81,5 90 88,25 91,75 100 98,25 101,75 31

39、46 110 108,25 111,75 41 56 120 118,25 121,75 51 66 36,5 54 130 128 132 55 70 40,5 58 140 138 142 65 80 50,5 68 36 56 150 148 152 75 90 60,5 78 46 66 160 156 164 85 100 70,5 88 56 76 180 176 184 105 120 90,5 108 76 96 61,5 84 200 195,4 204,6 125 140 110,5 128 96 116 81,5 104 67 92 220 215,4 224,6 132

40、 147 117,5 135 103 123 88,5 111 74 99 240 235,4 244,6 152 167 137,5 155 123 143 108,5 131 94 119 75,5 103 260 254,8 265,2 157,5 175 143 163 128,5 151 114 139 95,5 123 77 107 280 274,8 285,2 177,5 195 163 183 148,5 171 134 159 115,5 143 97 127 300 294,8 305,2 197,5 215 183 203 168,5 191 154 179 135,5

41、 163 117 147 320 314,3 325,7 203 223 188,5 211 174 199 155,5 183 137 167 340 334,3 345,7 223 243 208,5 231 194 219 175,5 203 157 187 360 354,3 365,7 243 263 228,5 251 214 239 195,5 223 177 207 380 374,3 385,7 248,5 271 234 259 215,5 243 197 227 400 394,3 405,7 268,5 291 254 279 235,5 263 217 247 420

42、 413,7 426,3 288,5 311 274 299 255,5 283 237 267 440 433,7 446,3 294 319 275,5 303 257 287 460 453,7 466,3 314 339 295,5 323 277 307 480 473,7 486,3 334 359 315,5 343 297 327 500 493,7 506,3 335,5 363 317 347 NOTE Preferred lengths are defined in terms of lsand lg. aP is the pitch of the thread. bFo

43、r lnomu 125 mm. cFor 125 mm 200 mm. ekw,min= 0,7 kmin. flg,max= lnom b. ls,min= lg,max 5 P. BS EN ISO 4016:2011ISO 4016:2011(E) ISO 2011 All rights reserved 5Table 2 Non-preferred threads Dimensions in millimetres Thread, d M14 M18 M22 M27 M33 Pa2 2,5 2,5 3 3,5 b 34 42 50 60 c 40 48 56 66 78 b ref.

44、d 53 61 69 79 91 c max. 0,6 0,8 0,8 0,8 0,8 damax. 16,7 21,2 26,4 32,4 38,4 max. 14,7 18,7 22,84 27,84 34 dsmin. 13,3 17,3 21,16 26,16 32 dwmin. 19,15 24,85 31,35 38 46,55 e min. 22,78 29,56 37,29 45,2 55,37 nom. 8,8 11,5 14 17 21 max. 9,25 12,4 14,9 17,9 22,05 k min. 8,35 10,6 13,1 16,1 19,95 kwemi

45、n. 5,85 7,42 9,17 11,27 13,97 r min. 0,6 0,6 0,8 1 1 nom. = max. 21,00 27,00 34 41 50 s min. 20,16 26,16 33 40 49 l lsand lgflslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min. max. 60 58,5 61,5 16 26 65 63,5 66,5 21 31 70 68,5 71,5 26 36 For sizes above the solid, bold,

46、stepped line, ISO 4018 is recommended. 80 78,5 81,5 36 46 25,5 38 90 88,25 91,75 46 56 35,5 48 27,5 40 100 98,25 101,75 56 66 45,5 58 37,5 50 110 108,25 111,75 66 76 55,5 68 47,5 60 35 50 120 118,25 121,75 76 86 65,5 78 57,5 70 45 60 130 128 132 80 90 69,5 82 61,5 74 49 64 34,5 52 140 138 142 90 100

47、 79,5 92 71,5 84 59 74 44,5 62 150 148 152 89,5 102 81,5 94 69 84 54,5 72 160 156 164 99,5 112 91,5 104 79 94 64,5 82 180 176 184 119,5 132 111,5 124 99 114 84,5 102 200 195,4 204,6 131,5 144 119 134 104,5 122 220 215,4 224,6 138,5 151 126 141 111,5 129 240 235,4 244,6 146 161 131,5 149 260 254,8 26

48、5,2 166 181 151,5 167 280 274,8 285,2 171,5 189 300 294,8 305,2 191,5 209 320 314,3 325,7 211,5 229 340 334,3 345,7 360 354,3 365,7 380 374,3 385,7 400 394,3 405,7 420 413,7 426,3 440 433,7 446,3 460 453,7 466,3 480 473,7 486,3 500 493,7 506,3 BS EN ISO 4016:2011ISO 4016:2011(E) 6 ISO 2011 All rights reservedTable 2 (continued) Dimensions in millimetres Thread, d M39 M45 M52 M60 Pa4 4,5 5 5,5 b c 90 1