EN ISO 1307-2008 en Rubber and plastics hoses - Hose sizes minimum and maximum inside diameters and tolerances on cut-to-length hoses《橡胶和塑料软管 软管尺寸 最小和最大内径及软管定长剪切的公差》.pdf

《EN ISO 1307-2008 en Rubber and plastics hoses - Hose sizes minimum and maximum inside diameters and tolerances on cut-to-length hoses《橡胶和塑料软管 软管尺寸 最小和最大内径及软管定长剪切的公差》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 1307-2008 en Rubber and plastics hoses - Hose sizes minimum and maximum inside diameters and tolerances on cut-to-length hoses《橡胶和塑料软管 软管尺寸 最小和最大内径及软管定长剪切的公差》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN ISO 1307:2008Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesICS 23.040.70g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g4

2、4g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN ISO 1307:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 55218 2National forewordThis British Standard is the UK implementation of

3、EN ISO 1307:2008. It is identical to ISO 1307:2006. It supersedes BS EN ISO 1307:1996 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee ca

4、n be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since pub

5、licationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 1307January 2008ICS 23.040.70 Supersedes EN ISO 1307:1995 English VersionRubber and plastics hoses - Hose sizes, minimum andmaximum inside diameters, and tolerances on cut-to-lengthhoses (ISO 1307:2006)Tuyaux en caoutchouc et

6、 en plastique - Dimensions destuyaux, diamtres intrieurs minimaux et maximaux, ettolrances sur la longueur de coupe (ISO 1307:2006)Gummi- und Kunststoffschluche - Schlauchmae, Kleinst-und Grt-Innendurchmesser, und Toleranzen beiabgelngten Schluchen (ISO 1307:2006)This European Standard was approved

7、by CEN on 26 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstand

8、ards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to

9、the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

10、lands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in a

11、ny form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 1307:2008: EForeword The text of ISO 1307:2006 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN

12、 ISO 1307:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2008

13、, and conflicting national standards shall be withdrawn at the latest by July 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Th

14、is document supersedes EN ISO 1307:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, G

15、reece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1307:2006 has been approved by CEN as EN ISO 1307:2008 without any

16、modifications. BS EN ISO 1307:2008Reference numberISO 1307:2006(E)INTERNATIONAL STANDARD ISO1307Fourth edition2006-09-15Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses Tuyaux en caoutchouc et en plastique Diamtres nominaux, diamtres i

17、ntrieurs minimaux et maximaux, et tolrances sur la longueur de coupe BS EN ISO 1307:2008ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carrie

18、d out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS

19、O collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Internatio

20、nal Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the ele

21、ments of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1307 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). This fourth edition cancels

22、 and replaces the third edition (ISO 1307:1992), which has been technically revised. The revision includes classifying the hoses by type according to the manufacturing process, adding additional sizes, and changing the inside-diameter tolerances to minimum and maximum dimensions to be consistent wit

23、h the latest hose standards. BS EN ISO 1307:2008blank1Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses 1 Scope This International Standard specifies the sizes of rubber and plastics hoses and the minimum and maximum inside diameters pe

24、rmitted for each hose size. For this purpose, hoses are divided into four types according to the process by which they are manufactured. The standard also specifies tolerances on cut-to-length rubber and plastics hoses for industrial and automotive applications. This standard is intended to be used

25、with the relevant hoses product standard unless there is justification for using a different hose size or unless a hose size needs a different inside-diameter range for a particular application. 2 Hose sizes and ID tolerances by manufacturing type The sizes of rubber and plastic hoses and their resp

26、ective inside-diameter ranges shall be in accordance with Table 1. Four types are specified, according to the process used to manufacture them: type A: hoses built using a rigid mandrel for inside-diameter control; type B: hoses built using a flexible mandrel for inside-diameter control (plus plasti

27、c hydraulic hoses made with or without a mandrel); type C: hoses built without using a mandrel (non-mandrel-built); type D: flexible extruded plastics hoses (type D does not include spiral-reinforced plastics suction and discharge hoses, which are classified as type C). BS EN ISO 1307:20082 Table 1

28、Hose sizes and inside-diameter tolerances Minimum and maximum inside-diameters mm Type A Built on rigid mandrel Type B Built on flexible mandrel Type C Non-mandrel-built (standard tolerance) Type D Extruded plastic Non-mandrel-built (tight tolerance) Nominal size min. max. min. max. min. max. min. m

29、ax. 3,2 3,2 3,8 N/A N/A N/A N/A 3,0 3,4 4 4,0 4,8 4,0 4,8 3,4 4,6 3,7 4,3 5 4,6 5,4 4,6 5,4 4,2 5,4 4,7 5,3 6,3 6,2 7,0 6,2 7,0 5,6 7,2 6,0 6,6 8 7,7 8,5 7,7 8,5 7,2 8,8 7,7 8,3 10 9,3 10,1 9,3 10,1 8,7 10,3 9,7 10,3 12,5 12,3 13,5 12,3 13,5 11,9 13,5 12,2 12,8 16 15,5 16,7 15,5 16,7 15,1 16,7 15,7

30、16,3 19 18,6 19,8 18,6 19,8 18,3 19,9 18,4 19,6 20 19,6 20,8 19,6 20,8 19,3 20,9 N/A N/A 25 25,0 26,4 25,0 26,4 24,2 26,6 24,4 25,6 31,5 31,4 33,0 31,4 33,0 30,2 33,4 30,9 32,1 38 37,7 39,3 37,7 39,3 36,5 39,7 37,4 38,6 40 39,7 41,3 39,7 41,3 38,5 41,7 N/A N/A 50 49,4 51,0 N/A N/A 48,1 51,6 N/A N/A

31、51 50,4 52,0 N/A N/A 49,1 52,6 50,2 51,8 63 63,1 65,1 N/A N/A 61,5 65,5 62,2 63,8 76 74,6 77,8 N/A N/A 74,2 78,2 75,0 77,0 80 78,6 81,8 N/A N/A 78,2 82,2 N/A N/A 90 87,3 90,5 N/A N/A N/A N/A N/A N/A 100 100,0 103,2 N/A N/A 99,4 103,9 N/A N/A 125 125,4 128,6 N/A N/A 124,8 129,3 N/A N/A 150 150,4 154,

32、4 N/A N/A 150,2 154,7 N/A N/A 160 N/A N/A N/A N/A 162,9 167,4 N/A N/A 200 200,7 205,7 N/A N/A 200,2 206,2 N/A N/A 250 251,0 257,0 N/A N/A 251,0 257,0 N/A N/A 305 301,8 307,8 N/A N/A 301,8 307,8 N/A N/A 315 314,5 320,5 N/A N/A N/A N/A N/A N/A 350 N/A N/A N/A N/A 351,6 359,6 N/A N/A 400 N/A N/A N/A N/

33、A 402,4 410,4 N/A N/A N/A = Not available. BS EN ISO 1307:200833 Tolerances on length The tolerances on cut-to-length hoses shall be in accordance with Table 2. Table 2 Tolerances on cut lengths of hose Length mm Tolerance u 300 3 mm 300 but u 600 4,5 mm 600 but u 900 6 mm 900 but u 1 200 9 mm 1 200

34、 but u 1 800 12 mm 1 800 1 % BS EN ISO 1307:2008BS EN ISO 1307:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It

35、 is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful i

36、f anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating

37、service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbs

38、i-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide

39、range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8

40、996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fa

41、x: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also hol

42、ds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recordin

43、g or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.