EN 61326-2-1-2006 en Electrical equipment for measurement control and laboratory use - EMC requirements - Part 2-1 Particular requirements - Test configurations operational conditi.pdf

《EN 61326-2-1-2006 en Electrical equipment for measurement control and laboratory use - EMC requirements - Part 2-1 Particular requirements - Test configurations operational conditi.pdf》由会员分享，可在线阅读，更多相关《EN 61326-2-1-2006 en Electrical equipment for measurement control and laboratory use - EMC requirements - Part 2-1 Particular requirements - Test configurations operational conditi.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 61326-2-1:2006Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-1: Particular requirements Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applicationsTh

2、e European Standard EN 61326-2-1:2006 has the status of a British StandardICS 17.220; 25.040.40; 33.100g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36

3、g58BS EN 61326-2-1:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISBN 0 580 48596 XNational forewordThis British Standard is the official English language version of EN 61326-2-1:2006. It is identical with IEC 61326

4、-2-1:2005. BS EN 61326-2-1:2006 partially supersedes BS EN 61326:1998 which will be withdrawn on publication of BS EN 61326-1:2006 and all of the parts of the BS EN 61326-2 series of standards (BS EN 61326-2-2:2006, BS EN 61326-2-3, BS EN 61326-2-4, BS EN 61326-2-5 and BS EN 61326-2-6:2006).The UK p

5、articipation in its preparation was entrusted by Technical Committee GEL/65, Measurement and control, to Subcommittee GEL/65/1, System considerations, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-reference

6、sThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Stan

7、dards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the

8、responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cove

9、r, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 61326-2-1 NORME EUROPENNE EUROPISCHE NORM May 2006 CENELEC European Commit

10、tee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC m

11、embers. Ref. No. EN 61326-2-1:2006 E ICS 17.220; 25.040.40; 33.100 Supersedes EN 61326:1997 + A1:1998 + A2:2001 + A3:2003English version Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-1: Particular requirements Test configurations, operational conditions and

12、 performance criteria for sensitive test and measurement equipment for EMC unprotected applications (IEC 61326-2-1:2005) Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-1: Exigences particulires Configurations dessai, conditions fonctionnelles et critre

13、s de performance pour essai de sensibilit et quipement de mesures pour les applications non protges de la CEM (CEI 61326-2-1:2005) Elektrische Mess-, Steuer-, Regel- und Laborgerte EMV-Anforderungen Tel 2-1: Besondere Anforderungen Prfanordnung, Betriebsbedingungen und Leistungsmerkmale fr empfindli

14、che Prf- und Messgerte fr Anwendungen ohne EMV-Schutzmanahmen (IEC 61326-2-1:2005) This European Standard was approved by CENELEC on 2006-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status o

15、f a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A v

16、ersion in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czec

17、h Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 65A/454/FDI

18、S, future edition 1 of IEC 61326-2-1, prepared by SC 65A, System aspects, of IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61326-2-1 on 2006-02-01. The EN 61326 series supersedes EN 61326:1997 + corrigendum Sep

19、tember 1998 + A1:1998 + A2:2001 + A3:2003. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-12-01 latest date by which the national standards conflicting with the EN have

20、to be withdrawn (dow) 2009-02-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Directive 89/336/EEC. See Annex ZZ. Annexes ZA and ZZ have been added by CENELEC. . _

21、Endorsement notice The text of the International Standard IEC 61326-2-1:2005 was approved by CENELEC as a European Standard without any modification. _ 2 EN 61326-2-1:2006ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-1: Particular requirements Test configur

22、ations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications 1 Scope In addition to the scope of IEC 61326-1, this part of IEC 61326 specifies more detailed test configurations, operational conditions and performance criteria f

23、or equipment with test and measurement circuits (both internal and/or external to the equipment) that are not EMC protected for operational and/or functional reasons, as specified by the manufacturer. The manufacturer specifies the environment for which the product is intended to be used and/or sele

24、cts the appropriate test level specifications of IEC 61326-1. NOTE Examples of equipment include, but are not limited to, oscilloscopes, logic analysers, spectrum analysers, network analysers, digital multimeters (DMM) and board test systems. 2 Normative references The following referenced documents

25、 are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050-161:1990, International Electrotechnical Vocabulary (IEV) Part 161: Elect

26、ro-magnetic compatibility IEC 61326-1:2005, Electrical equipment for measurement, control and laboratory use EMC requirements Part 1: General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 61326-1 and IEC 60050(161) apply. 4 General IEC

27、 61326-1 applies. 5 EMC test plan 5.1 General IEC 61326-1 applies. 3 EN 61326-2-1:20065.2 Configuration of EUT during testing IEC 61326-1 applies, except as follows: Addition: 5.2.401 I/O ports for Test and Measurement purposes (T&M ports) Test and Measurement (T&M) input ports shall be capped and s

28、horted unless this leads to an operating condition unsuitable for measuring the emission and immunity performance of the product. In this case, an appropriate input signal shall be applied. Test and Measurement (T&M) output ports not needed to evaluate the essential functions of the EUT shall be cap

29、ped and/or terminated. NOTE 1 Probes and/or test leads to be used with the test and measurement ports do not need to be connected. Such test leads can vary substantially from one application to another and are often connected to equipment that has the covers removed and may be in various stages of d

30、isassembly to provide access to test points inside. Connected test leads may increase emissions and/or reduce immunity in certain applications. NOTE 2 Capped means locally covered with a screen. 5.2.501 Auxiliary equipment Auxiliary equipment necessary for the normal operation of the equipment under

31、 test (EUT) shall be included as part of the equipment to be tested 5.3 Operation conditions of EUT during testing IEC 61326-1 applies, except as follows: Addition: 5.3.101 Operational conditions When both battery and a.c. options are available, both modes of operation shall comply. 5.3.102 Oscillos

32、copes The oscilloscope ports shall be set for maximum sweep speed, maximum sensitivity and continuous acquisition mode unless other modes are known to provide worst-case emission or immunity results within normal applications. 5.3.103 Logic analysers The logic analyser shall be set for data analysis

33、 modes during emissions testing and continuous data acquisition mode during immunity testing unless other modes are known to provide worst-case emission or immunity results within normal applications. 5.3.104 Digital multimeters (DMM) Typical set-ups include: peak detect, maximum sensitivity (usuall

34、y auto-range, if available, will suffice) and continuous acquisition mode. 4 EN 61326-2-1:20065.3.105 Other equipment For equipment not mentioned in 5.3.102 to 5.3.104, the following philosophy shall apply. A selection of representative operation modes shall be made, taking into account that not all

35、 functions, but only the most typical functions of the equipment can be tested. The estimated worst-case operating modes for normal application shall be selected 5.4 Specification of performance criteria IEC 61326-1 applies. 5.5 Test description IEC 61326-1 applies. 6 Immunity requirements 6.1 Condi

36、tions during the tests IEC 61326-1 applies. 6.2 Immunity test requirements IEC 61326-1 applies, except as follows: Addition: 6.2.101 Tests with transient electromagnetic phenomenon During testing, the EUT may have temporary degradation or loss of function or performance which is self-recovering. Sel

37、f-recovery times greater than 10 s shall be specified by the manufacturer. Trigger functions shall not be evaluated. No change in actual operating state or loss of stored data is allowed. Electrostatic discharges shall be applied to the housing shield, but not to the inner pins of shielded port or c

38、able connectors. Examples include: BNC, D-subminiature, IEEE 488 (GPIB), RS232 and IEEE 1284-B (parallel printer port), etc. 6.2.102 Tests with continuously present electromagnetic phenomenon No visual degradation of parameters of the EUT is allowed during application of the test, except as specifie

39、d by the manufacturer. No test for power frequency magnetic field is required. 6.3 Random aspects IEC 61326-1 applies. 5 EN 61326-2-1:20066.4 Performance criteria IEC 61326-1 applies, except as follows: Addition: 6.4.101 Oscilloscopes Typical parameters observed during immunity testing include trace

40、 width deviation, trace offset and display noise. 6.4.102 Logic analysers Typical parameters observed during immunity testing include logic analyser functional operations that may cause system lock-up or change of function or mode. 6.4.103 Digital multimeters (DMM) Typical parameters observed during

41、 immunity testing include the displayed measurement value. 7 Emission requirements IEC 61326-1 applies. 8 Test results and test report IEC 61326-1 applies. 9 Instructions for use IEC 61326-1 applies. 6 EN 61326-2-1:2006Bibliography IEEE 488, IEEE Standard For Higher Performance Protocol for the Stan

42、dard Digital Interface for Programmable Instrumentation IEEE 1284, IEEE Standard Signaling Method for a Bidirectional Parallel Peripheral Interface For Personal Computers _ 7 EN 61326-2-1:2006Annex ZA (normative) Normative references to international publications with their corresponding European pu

43、blications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publicatio

44、n has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60050-161 1990 International Electrotechnical Vocabulary Chapter 161: Electromagnetic compatibility IEC 61326-1 2005 Electrical equipment for measurement, control and la

45、boratory use EMC requirements Part 1: General requirements EN 61326-1 2006 8 EN 61326-2-1:2006Annex ZZ (informative) Coverage of Essential Requirements of EC Directives This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade As

46、sociation and within its scope the standard covers all relevant essential requirements as given in Article 4 of the EC Directive 89/336/EEC. Compliance with this standard provides one means of conformity with the specified essential requirements of the Directive concerned. WARNING: Other requirement

47、s and other EC Directives may be applicable to the products falling within the scope of this standard. _ 9 EN 61326-2-1:2006BS EN 61326-2-1:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It p

48、resents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BS

49、I to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest edition