EN 60626-3-2008 en Combined flexible materials for electrical insulation - Part 3 Specifications for individual materials (Incorporates Amendment A1 2012)《电气绝缘用复合柔性材料 第3部分 单项材料规范》.pdf

《EN 60626-3-2008 en Combined flexible materials for electrical insulation - Part 3 Specifications for individual materials (Incorporates Amendment A1 2012)《电气绝缘用复合柔性材料 第3部分 单项材料规范》.pdf》由会员分享，可在线阅读，更多相关《EN 60626-3-2008 en Combined flexible materials for electrical insulation - Part 3 Specifications for individual materials (Incorporates Amendment A1 2012)《电气绝缘用复合柔性材料 第3部分 单项材料规范》.pdf（78页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60626-3:2008Combined flexible materials for electrical insulation Part 3: Specifications for individual materialsICS 29.035.01 BS EN +A1:2012BS EN 60626-3:2008This British Standard waspublished under the authorityof the Standards Policy andStrategy Committee on 30 September 200

2、8 BSI 2008ISBN 978 0 580 56462 8National forewordThis British Standard is the UK implementation of EN 60626-3:2008. It isidentical to IEC 60626-3:2008. It supersedes BS EN 60626-3:1997 which iswithdrawn.The UK participation in its preparation was entrusted by Technical Committee GEL/15, Solid electr

3、ical insulating materials, to Subcommittee GEL/15/10,Combined flexible materials.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its corr

4、ect application.Compliance with a British Standard cannot confer immunity fromlegal obligations.Amendments/corrigenda issued since publicationDate CommentsBS EN 60626-3:2008This British Standard waspublished under the authorityof the Standards Policy andStrategy Committee on 30 September 2008 BSI 20

5、08IS N 978 0 580 56462 8National forewordThis British Standard is the UK implementation of EN 60626-3:2008. It isidentical to IEC 60626-3:2008. It supersedes BS EN 60626-3:1997 which iswithdraw .The UK participation in its preparation was entrusted by Technical CommitteeGEL/15, Solid electrical insu

6、lating materials, to Subcommittee GEL/15/10,Combined flexible materials.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not p rport to include all the necessary provisions of acontract. Us rs are responsible for its correct appli

7、cation.Compliance with a British Standard cannot confer immunity fromlegal obligations.Amendments/corrigenda issued since publicationDate Comments - : +A1:2012BS EN 60626-3:2008+A1:2012I 9 0 78647 1Amendments/corrigenda issued since publicationDate Comments28 February 2013 Implementation of IEC amen

8、dment 1:2012 withCENELEC endorsement A1:2012This British Standard waspublished under the authorityof the Standards Policy andStrategy Committee on 30 September 2008 The British StandardsInstitution 2013.Published by BSI StandardsLimited 2013is r is the UK i plementation of EN 60626-3:20 8+A1:2012.It

9、 is identical to IEC 60626-3:2008, incorporating amendment :2012. Itsupersedes BS EN 60626-3:2008, which will be withdrawn on 21 August 2015.The start and finish of text introduced or altered by amendment is indicatedin the text by tags. Tags indica g changes to IEC text carry the number of the IEC

10、amendmen . For example, text altered by IEC amendment 1 isindicated by .EUROPEAN STANDARD EN 60626-3NORME EUROPENNE EUROPISCHE NORMAugust 2008CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normun

11、gCentral Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 60626-3:2008 EICS 29.035.01 Supersedes EN 60626-3:1996 + A1:1999English versionCombined flexible materials for electri

12、cal insulation -Part 3: Specifications for individual materials(IEC 60626-3:2008)Matriaux combins souplesdestins lisolement lectrique -Partie 3: Spcificationspour matriaux particuliers (CEI 60626-3:2008)FlexibleMehrschichtisolierstofe zur elektrischen Isolation -Teil 3: Bestimmungenfr einzelne Mater

13、ialien (IEC 60626-3:2008)This European Standard was approved by CENELEC on 2008-08-01. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li

14、sts and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the re

15、sponsibility of a CENELEC member into its own language and notifiedto the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, theCzech Republic, Denmark, Estonia, Finland, France, Germany

16、, Greece, Hungary, Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.EN 60626-3:2008+A1September 2012Foreword The text of document 15/442/FDIS, future edition 3 of IE

17、C 60626-3, prepared by IEC TC 15 “Solidelectrical insulating materials“, was submitted to the IEC-CENELEC parallel vote and was approved byCENELEC as EN 60626-3 on 2008-08-01.This European Standard supersedes EN 60626-3:1996 + A1:1999.The main changes from EN 60626-3:1996 are as follows: consolidati

18、on of Amendment 1 published in 1999 which was mainly describing the sheets from 340 to459; revision and reordering of previous tables of EN 60626-3:1996.The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identicalnational standard

19、 or by endorsement (dop) 2009-05-01 latest date by which the national standards conflictingwith the EN have to be withdrawn (dow) 2011-08-01Annex ZA has been added by CENELEC._Endorsement noticeThe text of the International Standard IEC 60626-3:2008 was approved by CENELEC as a EuropeanStandard with

20、out any modification._ 2 BS EN 60626-3:2008- 2 -BS EN 60626-3:2008+A1:2012EN 60626-3:2008+A1:2012EN 60626-3:2008/A1:2012 - 2 - Foreword The text of document 15/647/CDV, future edition 1 of IEC 60626-3:2008/A1, prepared by IEC TC 15 “Solid electrical insulating materials“ was submitted to the IEC-CEN

21、ELEC parallel vote and approved by CENELEC as EN 60626-3:2008/A1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-05-21 latest date by which the national standa

22、rds conflicting with the document have to be withdrawn (dow) 2015-08-21 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement no

23、tice The text of the International Standard IEC 60626-3:2008/A1:2012 was approved by CENELEC as a European Standard without any modification. Foreword to amendment A1CONTENTSINTRODUCTION.51Scope62Normative references63Requirements74Designation.75Thermal clasification76Specification shets.7Sheet 100

24、Requirements for combined flexible duplex materials of two layers F-ET/P-C (23 m PET film with presspaper or paper)9Sheet 101 Requirements for combined flexible duplex materials of two layers F-ET/P-C (36 m PET film with presspaper or paper)11Sheet 102 Requirements for combined flexible duplex mater

25、ials of two layers F-PET/P-C (50 m PET film with presspaper or paper)13Sheet 110 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C (23 m PET film with presspaper or paper).15Sheet 111 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C

26、(36 m PET film with presspaper or paper).17Sheet 112 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C (50 m PET film with presspaper or paper).19Sheet 113 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C (75 m PET film with presspap

27、er or paper).21Sheet 114 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C (100 m PET film with presspaper or paper).23Sheet 115 Requirements for combined flexible triplex materials of three layers P-C/F-PET/P-C (125 m PET film with presspaper or paper).25Sheet 302 R

28、equirements for combined flexible duplex materials of two layers P-PAa/F-PET (50 m aramid calendered paper with PET film).27Sheet 303 Requirements for combined flexible duplex materials of two layers P-PAa/F-PET (80 m aramid calendered paper with PET film).29Sheet 312 Requirements for combined flexi

29、ble triplex materials of three layers P-PAa/F-PET/P-PAa (50 m aramid calendered paper on both sides of PET film)31Sheet 313 Requirements for combined flexible triplex materials of three layers P-PAa/F-PET/P-PAa (80 m aramid calendered paper on both sides of PET film)33Sheet 315 Requirements for comb

30、ined flexible triplex materials of three layers P-PAa/F-PET/P-PAa (130 m aramid calendered paper on both sides of PET film)35Sheet 320 Requirements for combined flexible triplex materials of three layers P-PAa/F-PET/P-PAa (130 m aramid uncalendered paper on both sides of PET film)37Sheet 330 Require

31、ments for combined flexible triplex materials of three layers P-PAa/F-PI/P-PAa (aramid calendered paper on both sides of PI film)39Sheet 340 Requirements for combined flexible duplex materials of two layers P-H/F-PET (hybrid inorganic-organic paper with PET film).41Sheet 350 Requirements for combine

32、d flexible triplex materials of three layers P-H/F-PET/P-H (75 m hybrid inorganic-organic paper on both sides of PET film)43Sheet 351 Requirements for combined flexible triplex materials of three layers P-H/F-PET/P-H (125 m hybrid inorganic-organic paper on both sides of PET film).45 3 BS EN 60626-3

33、:2008BS EN 60626-3:2008+A1:2012IEC 60626-3:2008+A1:2012- 3 -Sheet 352 Requirements for combined flexible triplex materials of three layers P-H/F-PET/P-H (60 nullm hybrid inorganic-organic paper on both sides of PET film) 47Sheet 360 Requirements for combined flexible triplex materials of three layer

34、s P-H/P-FG type 1/P-H (hybrid inorganic-organic paper on both sides of type 1 filled glass paper)47Sheet 400 Requirements for combined flexible duplex materials of two layers P-FG type 1/F-PET (type 1 filled glass paper with 25 m PET film).49Sheet 401 Requirements for combined flexible duplex materi

35、als of two layers P-FG type 1/F-PET (type 1 filled glass paper with 50 m PET film).51Sheet 402 Requirements for combined flexible duplex materials of two layers P-FG type 1/F-PET (type 1 filled glass paper with 75 m PET film).53Sheet 403 Requirements for combined flexible duplex materials of two lay

36、ers P-FG type 2/F-PET (type 2 filled glass paper with PET film).55Sheet 410 Requirements for combined flexible duplex materials of two layers P-FG type 1/C-G (type 1 filled glass paper with woven glass cloth)57Sheet 411 Requirements for combined flexible duplex materials of two layers P-FG type 2/C-

37、G (type 2 filled glass paper with woven glass cloth)59Sheet 420 Requirements for combined flexible triplex materials of three layers P-FG type 1/F-PET/P-FG type 1 (type 1 filled glass paper on both sides of PET film)61Sheet 421 Requirements for combined flexible triplex materials of three layers P-F

38、G type 2/F-PET/P-FG type 2 (type 2 filled glass paper on both sides of PET film)63Sheet 502 Requirements for combined flexible triplex materials of three layers P-PET/F-PET/P-PET (50 m PET mat on both sides of PET film)65Sheet 503 Requirements for combined flexible triplex materials of three layers

39、P-PET/F-PET/P-PET (75 m PET mat on both sides of PET film)67Sheet 505 Requirements for combined flexible triplex materials of three layers P-PET/F-PET/P-PET (125 m PET mat on both sides of PET film)69Bibliography71Annex ZA (normative) Normative references to international publications with their 4 B

40、S EN 60626-3:2008Table 1 Master listing for IEC 60626-3 sheet identification8corresponding European publications.72BS EN 60626-3:2008+A1:2012IEC 60626-3:2008+A1:2012 - 4 -4951535557596163656769717473INTRODUCTION This standard contains 31 sheets of Part 3, as follows: 100, 101, 102, 110, 111, 112, 11

41、3, 114, 115, 302, 303, 312, 313, 315, 320, 330, 340, 350, 351, 360, 400, 401, 402, 403, 410, 411, 420, 421, 502, 503, 505. 5 BS EN 60626-3:2008BS EN 60626-3:2008+A1:2012IEC 60626-3:2008+A1:2012- 5 -COMBINED FLEXIBLE MATERIALS FOR ELECTRICAL INSULATION Part 3: Specifications for individual materials

42、1 Scope This part of IEC 60626 specifies dimensional and performance requirements for individual combined flexible materials for electrical insulation. This part is in the form of groups of sheets.Sheets are numbered in accordance with Table 1, which provides a complete list of all the specification

43、 sheets belonging to this standard. Materials which conform to this specification meet established levels of performance. However,the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not b

44、ased on thisspecification alone. SAFETY WARNING It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. 2 Normative referencesThe following referenced documents are indispensable for the application of this document

45、. Fordated references, only the edition cited applies. For undated references, the latest edition ofthe referenced document (including any amendments) applies.The list of normative references is extensive because, in order to obtain a combination of two or more materials for electrical insulation, i

46、t is necessary that those base materials (paper, film, etc.) shall conform to the requirements set forth, in the appropriate specification of the base material alone, for that purpose. This rule shall be applied also in the development of newpossible combinations; to this end, specifications of mate

47、rials not actually used, but referenced, may be eligible for future developments.IEC 60554-1:1977, Specification for cellulosic papers for electrical purposes Part 1: Definitions and general requirementsIEC 60554-3 (all parts), Specification for cellulosic papers for electrical purposes Part 3: Spec

48、ifications for individual materialsIEC 60626-1:1995, Combined flexible materials for electrical insulation Part 1: Definitions and general requirementsIEC 60626-2:1995, Combined flexible materials for electrical insulation Part 2: Methodsof test IEC 60641-1:2008, Pressboard and presspaper for electrical purposes Part 1: Definitions and general requirementsIEC 60641-3-2:2008, Pressboard and presspaper for electrical purposes Part 3: Specifications for individual materials Sheet 2: Requirements for presspaper types P.2.1, P.4.1,