EN 60603-2-1998 en Connectors for Frequencies Below 3 MHz for Use with Printed Boards Part 2 Detail Specification for Two-Part Connectors with Assessed Quality for Printed Boards f.pdf

《EN 60603-2-1998 en Connectors for Frequencies Below 3 MHz for Use with Printed Boards Part 2 Detail Specification for Two-Part Connectors with Assessed Quality for Printed Boards f.pdf》由会员分享，可在线阅读，更多相关《EN 60603-2-1998 en Connectors for Frequencies Below 3 MHz for Use with Printed Boards Part 2 Detail Specification for Two-Part Connectors with Assessed Quality for Printed Boards f.pdf（86页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60603-2:1998IEC 60603-2: 1995QC 010000XX0002:1995Incorporating Amendment No. 1Harmonized system of quality assessment for electronic componentsConnectors for frequencies below 3 MHz for use with printed boards Part 2: Detail specification for two-part connectors with assessed q

2、uality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting featuresThe European Standard EN 60603-2:1998, with the incorporation of amendment A1:2005, has the status of a British StandardICS 31.220.10BS EN 60603-2:1998This British Standard, having been prepared under the dir

3、ection of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 October 1998 BSI 24 March 2006ISBN 0 580 30403 5National forewordThis British Standard is the official English language version of EN 60603-2:1998, including amendment A1

4、:2005. It is identical with IEC 60603-2:1995, including amendment 1:2000.The start and finish of text introduced or altered by IEC amendment is indicated in the text by tags !“. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is

5、 indicated by !“.The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present t

6、o the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained

7、 on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the

8、 BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of

9、pagesThis document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 81 and a back cover.This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.A

10、mendments issued since publicationAmd. No. Date Comments15818 March 2006 See national forewordBS EN 60603-2:1998 BSI 24 March 2006 iContentsPageNational foreword Inside front coverForeword 2Text of EN 60603-2 5iiblankEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 60603-2August 1998+ A1May 2005ICS

11、 31.220.10English versionConnectors for frequencies below 3 MHz for use with printed boards Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features(IEC 60603-2:1995 + A1:2000)(includes amendment

12、A1:2005)Connecteurs pour frquences infrieures 3 MHz pour utilisation avec cartes imprimes Partie 2: Spcification particulire pour connecteurs en deux parties pour cartes imprimes, avec assurance de la qualit, pour grilles de base de 2,54 mm (0,1 in) avec caractristiques de montage communes (CEI 6060

13、3-2:1995 + A1:2000) (inclut lamendement A1:2005)Steckverbinder fr gedruckte Schaltungen fr Frequenzen unter 3 MHz Teil 2: Bauartspezifikation fr gtebesttigte indirekte Steckverbinder fr gedruckte Schaltungen, Rasterma 2,54 mm (0,1 in), mit gemeinsamen Einbaumerkmalen (IEC 60603-2:1995 + A1:2000) (en

14、thlt nderung A1:2005)This European Standard was approved by CENELEC on 1998-08-01. Amendment A1 was approved by CENELEC on 2005-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nation

15、al standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in an

16、y other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finl

17、and, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENELECEuropean Committee for Electrotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normun

18、gCentral Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 60603-2:1998 + A1:2005 EEN 60603-2:1998 BSI 24 March 20062ForewordThe text of the International Standard IEC 60603-2:1995,

19、 prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as EN 60603-2 on 1998-08-01 without any modification.The following dates were fixed: Annexes designated “normat

20、ive” are part of the body of the standard.Annexes designated “informative” are given for information only.In this standard, Annex A and Annex ZA are normative and Annex B is informative.Annex ZA has been added by CENELEC.Endorsement noticeThe text of the International Standard IEC 60603-2:1995 was a

21、pproved by CENELEC as a European Standard without any modification.Foreword to amendment A1The text of amendment 1:2000 to the International Standard IEC 60603-2:1995, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was s

22、ubmitted to the formal vote and was approved by CENELEC as amendment A1 to EN 60603-2:1998 on 2005-04-01 without any modification.The following dates were fixed: Endorsement noticeThe text of amendment 1:2000 the International Standard IEC 60603-2:1995, was approved by CENELEC as an amendment to the

23、 European Standard without any modification. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1999-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1999-08-

24、01 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-04-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2008-04-01EN 60603-2:1998 BSI 24 Mar

25、ch 2006 3ContentsPageForeword ii1Scope 52 Normative references 53 IEC type designation 74 Common features 84.1 Mounting dimensions 84.2 Mating information 114.3 Survey of styles 125 Dimensions 135.1 General 135.2 Fixed board connectors 145.3 Free board connectors 305.4 Mating information 445.5 Acces

26、sories 445.6 Mounting information for fixed board connectors 465.7 Mounting information for free board connectors 496Gauges 526.1 Sizing gauges and retention force gauges 526.2 Test panel (for voltage proof test) 537 Characteristics 537.1 Climatic category 537.2 Electrical 547.3 Mechanical 598Test s

27、chedule 608.1 General 609 Quality assessment procedures 739.1 Qualification approval testing 739.2 Quality conformance inspection 739.3 Delayed delivery, re-inspection 7410 Ordering information 75Annex A (normative) Test phase BP 3.2: Corrosion, industrial atmosphere 76Annex B (informative) Special

28、contacts for connectors Style M 77Annex C (normative) Inductance test method 79Annex ZA (normative) Normative references to international publications with their corresponding European publications 80Figure 1 Isometric view 9Figure 2 Plug-in direction 11Figure 3 Perpendicular to plug-in direction 11

29、Figure 4 Inclination 12PageFigure 5 Styles B, C, D and E 14Figure 6 Terminations 17Figure 7 Styles F and G 19Figure 8 Terminations 21Figure 9 Style M 22Figure 10 Styles Q, R, S and T 24Figure 11 Styles U and V 26Figure 12 Style H 28Figure 13 Termination 29Figure 14 Styles B, C, D and E 30Figure 15 S

30、tyles F and G 34Figure 16 Style M 36Figure 17 Styles Q, R, S and T 38Figure 18 Styles U and V 40Figure 19 Style H 42Figure 20 Terminations 43Figure 21 Example for external coding 45Figure 22 Hole pattern on printed boards for Styles B, C, D, E, Q, R, S and T 46Figure 23 Hole pattern on printed board

31、s for Styles F, G, U and V 47Figure 24 Mounting on panels 47Figure 25 Hole pattern on printed boards for Style M 48Figure 26 Mounting information for free board connectors 49Figure 27 Mounting information for free board connectors 50Figure 28 Mounting information for free board connectors 51Figure 2

32、9 Gauge dimensions 52Figure 30 Test panel (for voltage proof test) 53Figure 31 Styles B, C, M, Q and R 54Figure 32 Styles D, E, F, G, S, T, U and V 55Figure 33 Style H 55Figure 34 Solder and wrapped connections 56Figure 35 Insulation displacement 56Figure 36 Flat tab 56Figure 37 Screw terminal 56Fig

33、ure 38 Arrangement for connectors without cable/wires 61Figure 39 Arrangement for connectors with ribbon cable (insulation displacement) 61Figure 40 Arrangement for connectors with wires (flat tab, screw terminal) 62Figure 41 Arrangement for flammability test 62EN 60603-2:19984 BSI 24 March 2006Page

34、Figure 42 Arrangement for static load, axial 63Figure 43 Wiring arrangement for insulation resistance, voltage proof and polarization voltage during damp heat test 63Figure B.1 Mating conditions (plug-in direction) for special contacts 77Figure B.2 Example of a tool used for insertion and extraction

35、 78Figure C.1 Inductance test measuring points 79Table 1 Isometric view and values 8Table 2 Survey of styles 12Table 3 Dimensions common to Styles B, C, D and E15Table 4 Dimensions peculiar to Styles B, C, D and 6Table 5 Contact arrangement of Styles B, C, D, E, Q, R, S and T 16Table 6 Dimensions of

36、 Styles B, C, D, E, Q, R, S, T, M and H terminations 18Table 7 Dimensions common to Styles F and G 20Table 8 Dimensions peculiar to Styles F and G 20Table 9 Contact arrangement of Styles F, G, U and V 20Table 10 Dimensions of Styles F, G, U and V terminations 21Table 11 Dimensions common to Style M

37、23Table 12 Dimensions peculiar to Style M 23Table 13 Contact arrangement of Style M 23Table 14 Dimensions common to Styles Q, R, S and T 25Table 15 Dimensions peculiar to Styles Q, R, S and T 25Table 16 Dimensions common to Styles U and V27Table 17 Dimensions peculiar to Styles U and V 27Table 18 Di

38、mensions of Style H terminations 29Table 19 Dimensions common to Styles B, C, D and E 31Table 20 Dimensions peculiar to Styles B, C, D and E 32Table 21 Contact arrangement of Styles B, C, D, E, Q, R, S and T 33Table 22 Dimensions common to Styles F and G35PageTable 23 Dimensions peculiar to Styles F

39、 and G 35Table 24 Contact arrangements of Styles F, G, U and V 35Table 25 Dimensions common to Style M 37Table 26 Dimensions peculiar to Style M 37Table 27 Dimensions common to Styles Q, R, S and T 39Table 28 Dimensions peculiar to Styles Q, R, S and T 39Table 29 Dimensions common to Styles U and V4

40、1Table 30 Dimensions peculiar to Styles U and Table 31 Dimensions of Style H terminations 43Table 32 Dimensions 45Table 33 Mounting dimensions 47Table 34 Mounting on panels 48Table 35 Hole pattern on printed boards for Style M48Table 36 Mounting dimensions for free board connectors 51Table 37 Gauges

41、 52Table 38 Test panel (for voltage proof test) 53Table 39 Climatic category 53Table 40 Voltage proof (applicable for PL 1, 2, 3) 54Table 41 Insertion and withdrawal forces 59Table 42 Vibration (sinusoidal) 59Table 43 Mechanical operation 59Table 44 Test specimens 60Table 45 Performance levels 73Tab

42、le 46 Lot-by-lot tests 73Table 47 Periodic tests 74Table 48 Delayed delivery, re-inspection assessment level 75Table B.1 Survey of special contacts for use with connectors 78EN 60603-2:1998 BSI 24 March 2006 51 ScopeThis International Standard applies to groups of related connectors for use with pri

43、nted boards. They range from connectors with high contact density for low-voltage applications (Styles B and C) to connectors for heavy currents and high voltages having fewer contacts (Styles D, E, F, G and H). !It also applies to style W two-part connectors which have ground planes added to type C

44、 connectors to provide additional ground required for frequencies above 3 MHz.“It also applies to Style M two-part connectors supplied in alternative versions having 2, 4 or 6 holes for fitting special contacts, for example coaxial, for high voltages or heavy currents (see Annex B), as well as 78, 6

45、0 or 42 normal contacts identical with those of style C.It applies further to two-part connectors of Styles Q, R, S, T, U and V whose male contacts are fitted to the fixed board connectors and the female contacts to the free board connectors.All these connectors have the same fitting characteristics

46、 irrespective of their various utilization characteristics. The part of the connector fitted to the board is provided with terminations suitable for printed boards in accordance with IEC 326-3 using a grid of 2,54 mm (0,1 in), as defined in IEC 97.The free board connectors are provided either with s

47、older or flat quick-connect terminations. The fixed board connectors are provided either with solder, insulation displacement, wrapped connections or with screw terminals and flat quick-connect terminations. The terminations of the fixed board connectors are located in such a way as to be suitable f

48、or use with mother boards using a grid of 2,54 mm (0,1 in) as defined in IEC 97 as well as for automating wiring techniques.2 Normative referencesThe following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 603. At the time of

49、publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this part of IEC 603 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.