EN 60154-1-2016 en Flanges for waveguides - Part 1 General requirements.pdf

《EN 60154-1-2016 en Flanges for waveguides - Part 1 General requirements.pdf》由会员分享，可在线阅读，更多相关《EN 60154-1-2016 en Flanges for waveguides - Part 1 General requirements.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Flanges for waveguidesPart 1: General requirementsBS EN 60154-1:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 60154-1:2016. It isidentical to IEC 60154-1:2016. It supersedes BS EN 60154-1:199

2、6 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its sec

3、retary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 87379 9ICS 33.120.10Compliance with a British Standard cannot

4、 confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60154-1:2016EUROPEAN STANDARD NORME EUROPENNE EUROPI

5、SCHE NORM EN 60154-1 September 2016 ICS 33.120.10 Supersedes EN 60154-1:1994English Version Flanges for waveguides - Part 1: General requirements (IEC 60154-1:2016) Brides pour guides dondes - Partie 1: Exigences gnrales (IEC 60154-1:2016) Flansche fr Hohlleiter - Teil 1: Allgemeine Anforderungen (I

6、EC 60154-1:2016) This European Standard was approved by CENELEC on 2016-06-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

7、 bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under t

8、he responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estoni

9、a, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee fo

10、r Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Mem

11、bers. Ref. No. EN 60154-1:2016 EBS EN 60154-1:2016EN 60154-1:2016 2 European foreword The text of document 46F/304/CDV, future edition 3 of IEC 60154-1, prepared by SC 46F “RF and microwave passive components“, of IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF and microwave passive componen

12、ts and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60154-1:2016. The following dates are fixed: x latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-03-2

13、2 x latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-06-22 This document supersedes EN 60154-1:1994. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall

14、 not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60154-1:2016 was approved by CENELEC as a European Standard without any modification. BS EN 60154-1:2016EN 60154-1:2016 3 Annex ZA (normative) Normative references to

15、 international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edi

16、tion of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex

17、is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60050 series International Electrotechnical Vocabulary (IEV) - - IEC 60068 series Environmental testing EN 60068 series IEC 60153 series Hollow metallic waveguides EN 60153 series BS EN 60154-1:2016 2 IEC 60154-1:2016 IEC 2016

18、CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms and definitions 6 4 General . 6 4.1 Flange designation 6 4.2 Standard atmospheric conditions for testing . 7 4.3 Visual inspection . 7 5 Mechanical requirements . 7 5.1 General requirements both for mounted and unmoun

19、ted flanges 7 5.1.1 Holes . 7 5.1.2 Shank diameter of bolts used for alignment 7 5.1.3 Relation between shank or alignment pin and alignment hole diameters 8 5.1.4 Overall dimensions and thickness of flanges . 8 5.1.5 Surface roughness of contact area of contact flanges . 9 5.1.6 Flatness of contact

20、 area . 9 5.1.7 Perpendicularity of the axis of the holes . 9 5.1.8 General requirements for mounted flanges (assemblies) . 9 5.2 Additional requirements for unmounted flanges 9 5.2.1 General . 9 5.2.2 Shape of aperture 9 5.2.3 Positioning of the holes 10 5.2.4 Ordering information 10 Table 1 Shank

21、diameters . 8 BS EN 60154-1:2016IEC 60154-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FLANGES FOR WAVEGUIDES Part 1: General requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrot

22、echnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specificati

23、ons, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International,

24、 governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decis

25、ions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for intern

26、ational use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In ord

27、er to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be cle

28、arly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification

29、bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, prop

30、erty damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in

31、this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any

32、 or all such patent rights. International Standard IEC 60154-1 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories. This third edition cancels and repl

33、aces the second edition published in 1982. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) define the alignment pin and hole for waveguide alignment; b) specify the dimensions in the metric syst

34、em. BS EN 60154-1:2016 4 IEC 60154-1:2016 IEC 2016 The text of this standard is based on the following documents: CDV Report on voting 46F/304/CDV 46F/318/RVCFull information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publi

35、cation has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60154 series, published under the general title Flanges for waveguides, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged unt

36、il the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be x reconfirmed, x withdrawn, x replaced by a revised edition, or x amended. BS EN 60154-1:2016IEC 60154-1:2016 IEC 2016 5 INTRODUCTIO

37、N This International Standard relates to straight hollow metallic tubing for use as waveguides in electronic equipment. In recent years, the operation frequency of waveguide components and systems has been extended to 1 THz and above. However, the IEC 60154 series of standards for flanges for wavegu

38、ides, currently specifies the interface design up to 40 GHz for rectangular waveguides. In addition to this, the current issues of the IEC 60154 series of standards were issued in the 1970s and do not meet the needs of current applications. This new edition of IEC 60154-1 addresses these two issues.

39、 BS EN 60154-1:2016 6 IEC 60154-1:2016 IEC 2016 FLANGES FOR WAVEGUIDES Part 1: General requirements 1 Scope This part of IEC 60154 specifies the dimensions of waveguide flanges for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It shou

40、ld be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well a

41、s to ensure adequate electrical performance. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of

42、 the referenced document (including any amendments) applies. IEC 60050 (all parts), International Electrotechnical Vocabulary (available at http:/www.electropedia.org/) IEC 60068 (all parts), Environmental testing IEC 60153 (all parts), Hollow metallic waveguides 3 Terms and definitions For the purp

43、oses of this document, the terms and definitions given in IEC 60050-726 apply. 4 General 4.1 Flange designation Waveguide flanges covered by this standard shall be indicated by a reference number comprising the following information: a) the number of the present IEC publication (60154); b) the lette

44、rs “IEC“; c) a dash; d) a letter relating to the basic construction of the flange style, i.e.: P = a flange having a gasket groove but no choke groove (formerly called pressurizable); C = a choke flange with a gasket groove (formerly called choke, pressurizable); BS EN 60154-1:2016IEC 60154-1:2016 I

45、EC 2016 7 U = a flange having neither a gasket groove nor a choke groove (formerly called unpressurizable1); e) a letter for the type according to the drawing. Flanges with the same letter and of the same waveguide size can be mated; f) the letter and number of the waveguide for which the flange is

46、designed. Example: “60154 IEC-CBR 100“ denotes a choke flange of type B for ordinary rectangular waveguide 60153 IEC-R 100. 4.2 Standard atmospheric conditions for testing Unless otherwise specified, all tests shall be carried out under standard atmospheric conditions for testing as specified in IEC

47、 60068. Before the measurements are made, the flanges shall be stored at the measuring temperature for a time sufficient to allow the entire waveguide to reach this temperature. When measurements are made at a temperature other than the specified temperature, the results shall, where necessary, be c

48、orrected to the specified temperature. The ambient temperature at which the measurements are made shall be stated in the test report. 4.3 Visual inspection Waveguide flanges shall be uniform in composition. There shall be no burrs, cracks, die marks, dirt, grease, scale nor splinters. Contact surfac

49、es shall have a clean appearance in accordance with good current practice. Compliance is checked by visual inspection. 5 Mechanical requirements 5.1 General requirements both for mounted and unmounted flanges 5.1.1 Holes Holes which are intended as alignment holes shall be precision drilled and clearly indicated on the drawing. Holes which are not intended for alignment, i.e. attachment holes, may be less accurately located than are the alignment holes, but shall then be of correspondingly larger diameter t