EN 60153-1-2016 en Hollow metallic waveguides - Part 1 General requirements and measuring methods.pdf

《EN 60153-1-2016 en Hollow metallic waveguides - Part 1 General requirements and measuring methods.pdf》由会员分享，可在线阅读，更多相关《EN 60153-1-2016 en Hollow metallic waveguides - Part 1 General requirements and measuring methods.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、Hollow metallic waveguidesPart 1: General requirements and measuring methodsBS EN 60153-1:2016Incorporating corrigendum February 2017BSI Standards PublicationBS EN 60153-1:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 60153-1:2016, incorporating corrigend

2、um February 2017. It is identical to IEC 60153-1:2016.The UK participation in its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee c

3、an be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 97920 0ICS 33.120.10Com

4、pliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate Text affected31 March 2017 Implementation of CE

5、NELEC corrigendum February 2017: CENELEC supersession information correctedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60153-1 September 2016 ICS 33.120.10 English Version Hollow metallic waveguides - Part 1: General requirements and measuring methods (IEC 60153-1:2016) Guides dondes mtalli

6、ques creux - Partie 1: Exigences gnrales et mthodes de mesure (IEC 60153-1:2016) Metallische Hohlleiter - Teil 1: Allgemeine Anforderungen und Messverfahren (IEC 60153-1:2016) This European Standard was approved by CENELEC on 2016-06-22. CENELEC members are bound to comply with the CEN/CENELEC Inter

7、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

8、CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offi

9、cial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

10、Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENEL

11、EC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60153-1:2016 ESupersedes HD 123.1 S1:1977EN 60153-1:2016 2 European foreword The text of document 46F/302/CDV, future editi

12、on 2 of IEC 60153-1, prepared by SC 46F “RF and microwave passive components“, of IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60153-1:2016. The following dates a

13、re fixed: g120 latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-03-22 g120 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-06-22 Attention

14、is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60153-1:2016 was approved by CENEL

15、EC as a European Standard without any modification. BS EN 60153-1:2016This document supersedes HD 123.1 S1:1977.EN 60153-1:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are n

16、ormatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified

17、 by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60050 series International Electrotechnical Vocabular

18、y (IEV) - - IEC 60068 series Environmental testing EN 60068 series IEC 60154 series Flanges for waveguides EN 60154 series IEC 60261 - Sealing test for pressurized waveguide tubing and assemblies HD 138 S2 - BS EN 60153-1:2016 2 IEC 60153-1:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scop

19、e 6 2 Normative references. 6 3 Terms and definitions 6 4 Type designation . 7 4.1 Type . 7 4.2 Designation . 7 5 Standard atmospheric conditions for testing . 8 6 Visual inspection . 8 7 Mechanical requirements . 8 7.1 Dimensions . 8 7.1.1 General . 8 7.1.2 Ordinary rectangular waveguides . 9 7.1.3

20、 Rectangularity of cross-section . 10 7.1.4 Flat rectangular waveguides . 10 7.1.5 Circular waveguides . 11 7.2 Other mechanical requirements . 11 7.2.1 Bow . 11 7.2.2 Twist 12 7.2.3 Surface roughness . 12 7.2.4 Internal stress 12 8 Electrical tests . 12 8.1 Attenuation . 12 8.2 Internal reflections

21、 from irregularity of internal dimensions . 13 9 Additional tests Gas tightness . 14 BS EN 60153-1:2016IEC 60153-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HOLLOW METALLIC WAVEGUIDES Part 1: General requirements and measuring methods FOREWORD 1) The International Electrotechnical

22、Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end

23、and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Commit

24、tee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in acco

25、rdance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all in

26、terested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held respo

27、nsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergenc

28、e between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks

29、 of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts

30、and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publi

31、cation or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publi

32、cation may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60153-1 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF con

33、nectors, RF and microwave passive components and accessories. This second edition cancels and replaces the first edition published in 1964. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) expand

34、 the operation frequency range; b) revise the equation of attenuation. BS EN 60153-1:2016 4 IEC 60153-1:2016 IEC 2016 The text of this standard is based on the following documents: CDV Report on voting 46F/302/CDV 46F/316/RVCFull information on the voting for the approval of this standard can be fou

35、nd in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. It is to be read in conjunction with IEC 60154: Flanges for waveguides. A list of all parts in the IEC 60153 series, published under the general title Hollow

36、metallic waveguides, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publicati

37、on will be g120 reconfirmed, g120 withdrawn, g120 replaced by a revised edition, or g120 amended. BS EN 60153-1:2016IEC 60153-1:2016 IEC 2016 5 INTRODUCTION This International Standard relates to straight hollow metallic tubing for use as waveguides in electronic equipment. In recent years, the oper

38、ation frequency of waveguide components and systems has been extended to 1 THz and above. However, the first edition of the IEC 60153 series of standards only specified the aperture dimensions for ordinary rectangular waveguide for frequencies up to 325 GHz. In addition, the first edition of the IEC

39、 60153 series of standards, dating from the 1960s, does not meet the needs of the current applications. This new edition of IEC 60153-1 addresses these two issues by extending the frequency coverage to 3 300 GHz and by addressing current applications for this type of waveguide. This standard takes i

40、nto account IEC 60068 when necessary. When there is a difference between the general requirements and the relevant specification sheet, the latter prevails. BS EN 60153-1:2016 6 IEC 60153-1:2016 IEC 2016 HOLLOW METALLIC WAVEGUIDES Part 1: General requirements and measuring methods 1 Scope This part

41、of IEC 60153 specifies straight hollow metallic tubing for use as waveguides in electronic equipment. It covers: a) the details necessary to ensure compatibility and, as far as essential, interchangeability; b) test methods; c) uniform requirements for the electrical and mechanical properties. It sh

42、ould be noted that no recommendations are made for the materials to be used for waveguides. The choice of material is agreed between customer and manufacturer. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for i

43、ts application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050 (all parts), International Electrotechnical Vocabulary (available at g31http:/www.electropedia.org/) IEC 60068 (al

44、l parts), Environmental testing IEC 60154, Flanges for waveguides IEC 60261, Sealing test for pressurized waveguide tubing and assemblies 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60050, as well as the following apply. 3.1 type test complete se

45、ries of tests to be carried out on a number of specimens representative of the type, with the object of determining whether a particular manufacturer can be considered to be able to produce products meeting the specification 3.2 type approval decision by the proper authority (the customer himself or

46、 his nominee) that a particular manufacturer can be considered to be able to produce in reasonable quantities the type meeting the specification BS EN 60153-1:2016IEC 60153-1:2016 IEC 2016 7 3.3 acceptance tests tests carried out to determine the acceptability of a consignment on the basis of an agr

47、eement between customer and manufacturer Note 1 to entry: The agreement shall cover: a) the sample size, b) the selection of tests, c) the extent to which the specimens shall conform to the requirements for the selected tests of the specification. Note 2 to entry: In cases of divergent test results,

48、 the IEC standard test methods shall be used for acceptance tests. As these recommendations only cover type tests, these definitions are included only for brief information of testing specification. 3.4 factory tests tests carried out by the manufacturer to verify that their products meet the specif

49、ication 4 Type designation 4.1 Type Type of products comprises similar design features manufactured by the same techniques and falling within the manufacturers usual range of ratings for these products. NOTE 1 Mounting accessories are ignored, provided they have no significant effect on the test results. NOTE 2 Ratings cover the combination of: a) electrical ratings, b) sizes, c) environmental group. NOTE 3 The limits of the range of ratings shall be agreed between customer and manufacturer. 4.2 Designation The reference i