EN 50289-3-2-2001 en Communication Cables - Specifications for Test Methods Part 3-2 Mechanical Test Methods - Tensile Strength and Elongation for Conductor《通信电缆 试验方法规范 第3-2部分 机械试验.pdf

《EN 50289-3-2-2001 en Communication Cables - Specifications for Test Methods Part 3-2 Mechanical Test Methods - Tensile Strength and Elongation for Conductor《通信电缆 试验方法规范 第3-2部分 机械试验.pdf》由会员分享，可在线阅读，更多相关《EN 50289-3-2-2001 en Communication Cables - Specifications for Test Methods Part 3-2 Mechanical Test Methods - Tensile Strength and Elongation for Conductor《通信电缆 试验方法规范 第3-2部分 机械试验.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Communication cables - Specifications for test methods - Part 3-2: Mechanical test methods - Tensile strength and elongation for conductor The European Standard EN 50289-3-2:2001 has the status of a British Standard ICs 33.120.10 BS EN 50 289-3-2 :20 O 1 NO COPYING WITHOUT BSI PERMI

2、SSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 50289-3-2:ZOOl National foreword This British Standard is the official English language version of The UK participation in its preparation was entrusted by Technical Committee EPL46, Cables, wire and waveguides, RF connectors, and accessories for comm

3、unication and signalling, to Subcommittee EPL/46/1, Communication cables, which has the responsibility to: EN 50289-3-2:2001. - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interest

4、s informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications ref

5、erred to in this document may be found in the BSI Standards Catalogue under the section entitled lnternational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a

6、contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having Summary of pages This document comprises a front cover, an inside front cover, the EN title

7、page, been prepared under the direction of the Electrotechnical Sector policv and Strategy Committee, was published under the authority ofthe Standards policy and pages 2 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the Strategy Committee on 14 November 200

8、1 document was last issued. Amendments issued since publication Amd. No. IDate I Comments Q BSI 14 November 2001 ISBN O 580 38687 2 EUROPEAN STANDARD EN 50289-3-2 NORME EUROPENNE EUROPISCHE NORM August 2001 ICs 33.120.10 English version Communication cables - Specifications for test methods Part 3-2

9、: Mechanical test methods - Tensile strength and elongation for conductor Cbles de communication - Spcification des mthodes dessais Partie 3-2: Mthodes dessais mcaniques - Rsistance la traction et allongement des conducteurs Kommuni kations ka bel - Spezifikationen fr Prfverfahren Teil 3-2: Mechanis

10、che Prfverfahren - Zugfestigkeit und Dehnung fr Leiter This European Standard was approved by CENELEC on 2001-07-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

11、 any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language

12、made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Ger

13、many, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Se

14、cretariat: rue de Stascart 35, B - 1050 Brussels O 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 502893-2:2001 E EN 50289-3-212001 -2- Foreword This European Standard was prepared by the Technical Committee CENELEC TC 46X,

15、Communication cables. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50289-3-2 on 2001-07-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standa

16、rd or by endorsement (dop) 2002-08-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2004-08-01 This European Standard has been prepared under the European Mandate M212 given to CENELEC by the European Commission and the European Free Trade Associati

17、on. -3- EN 50289-3-2:2001 Contents 1 Scope . 4 2 Normative references . 4 3 Definitions . 4 4 Test method . 4 4 . I Tensile strength and elongation after break for metals 4 4 . I . I Principle . 4 4.1.2 Procedure 4 Tensile strength and elongation at break for metals . 5 4.2. I Principle . 5 4.2.2 Te

18、st equipment . 5 4.2.4 Expression of results . 5 4.2 4.2.3 Procedure 5 5 Test report . 5 EN 50289-3-2:2001 -4- 1 Scope This Part 3-2 of EN 50289 details the methods of test to determine the tensile strength and elongation of conductors of cables used in analogue and digital communication systems. It

19、 is to be read in conjunction with Part 3-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate plac

20、es in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication refer

21、red to applies (including amendments). EN 50289-3-1 2001 Communication cables - Specifications for test methods - Part 3-1: Mechanical test methods - General requirements EN 50290-1-2 Communication cables - Part 1-2: Definitions ISOIR402 Tensile testing of copper and copper alloy wire 3 Definitions

22、For the purposes of this European Standard the definitions of EN 50290-1-2 apply. 4 Test method 4. I Tensile strength and elongation after break for metals. 4.1 .I Principle The test determines the maximum load and the plastic extension of the solid conductor with high elongation. (e.g. aluminium, c

23、opper) 4.1 -2 Procedure At least five test specimens shall be tested in accordance with the method specified in ISOIR 402 with a rate of separation of the jaws of 1 O0 mm f 20 mmhin. ) At draft stage. -5- EN 50289-3-2:2001 4.2 Tensile strength and elongation at break for metals 4.2.1 Principle The t

24、est determines the percentage elongation at the time of break of a solid conductor with low elongation of about 1% (e.g. steel). 4.2.2 Test equipment An extensometer or other device suitable for measuring elongation of a gauge length of 250 mm shall be used. The equipment shall have a resolution not

25、 worse than 0,25 mm. 4.2.3 Procedure At least five test specimens shall tested. Each of them shall successively be fitted in the jaws of the testing machine and loaded to 10 percent of the minimum specified breaking load. An extensometer or other suitable device shall be attached to the test specime

26、n to measure the extension. The elongation versus the load shall be observed while applying a tensile load to the specimen. The reading of elongation and tensile load at break shall be recorded. The rate of separation of the jaws shall not be greater than 100 rnm f 20 mm/min. Tests in which the frac

27、ture occurs within 25 mm apart from the jaws or extensometer clamps shall be disregarded and a repeat test shall be carried out 4.2.4 Expression of results The elongation at break shall be expressed as a percentage of the original sample length. Tensile load shall be expressed in N/rnm2. 5 Test repo

28、rt The test report shall include: - temperature, - sample length, - - elongation of each of the specimens, breaking load for each of the specimens. BS EN 5 O 289-3-2:2 O0 1 BSI 389 Chiswick High Road London W4 4AL BSI - British Standards Institution BSI is the independent national body responsible f

29、or preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or

30、 editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on t

31、he inside front cover. Tel: O20 8996 9000. Fax: O20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications sh

32、ould be addressed to Customer Services. Tel: O20 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at htta:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Stand

33、ards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on

34、all its products and services. Contact the Information Centre. Tel: O20 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Memb

35、ership Administration. Tel: O20 8996 7002. Fax: O20 8996 7001. Further information about BSI is available on the BSI website at :/www. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Excep

36、t as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use,

37、in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: O20 8996 7070.