EN 16263-2-2015 en Pyrotechnic articles - Other pyrotechnic articles - Part 2 Requirements《烟火制品 其他烟火制品 第2部分 要求》.pdf

《EN 16263-2-2015 en Pyrotechnic articles - Other pyrotechnic articles - Part 2 Requirements《烟火制品 其他烟火制品 第2部分 要求》.pdf》由会员分享，可在线阅读，更多相关《EN 16263-2-2015 en Pyrotechnic articles - Other pyrotechnic articles - Part 2 Requirements《烟火制品 其他烟火制品 第2部分 要求》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 16263-2:2015Pyrotechnic articles Other pyrotechnic articlesPart 2: RequirementsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 16263-2:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16263-2:2015. The UK particip

2、ation in its preparation was entrusted to TechnicalCommittee CII/47, Pyrotechnic articles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible f

3、or its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 74544 7 ICS 71.100.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Pol

4、icy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 16263-2:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16263-2 August 2015 ICS 71.100.30 English Version Pyrotechnic articles - Other pyrotechnic articles - Part 2

5、: Requirements Articles pyrotechniques - Autres articles pyrotechniques - Partie 2 : Exigences Pyrotechnische Gegenstnde - Sonstige pyrotechnische Gegenstnde - Teil 2: Anforderungen This European Standard was approved by CEN on 6 February 2015. CEN members are bound to comply with the CEN/CENELEC In

6、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to a

7、ny CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

8、versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw

9、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of explo

10、itation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16263-2:2015 EBS EN 16263-2:2015 EN 16263-2:2015 (E) 2 Contents Page European foreword .4 1 Scope 5 2 Normative references 6 3 Terms and definitions .6 4 General and safety requirements .6 4.1 Incompatible

11、substances 6 4.2 Safe disposal 6 4.3 Means of ignition .6 4.4 Safety features .7 4.5 Toxicity .7 5 Performance requirements .7 5.1 Verification of performance 7 5.2 Verification of design 8 5.3 Verification of labelling and instructions for use .8 5.4 Resistance to mechanical impact 8 5.5 Loose pyro

12、technic composition after mechanical conditioning and mechanical impact test .8 5.6 Resistance to moisture .9 5.7 Resistance to high and low temperatures 9 5.8 Integrity .9 6 Requirements for semi-finished pyrotechnic articles and rocket motors .9 6.1 Semi-finished pyrotechnic articles 9 6.2 Rocket

13、motors 9 7 Primary pack 9 8 Type testing . 10 8.1 General . 10 8.2 Number of items to be tested 10 8.2.1 General . 10 8.2.2 Additional items for specific tests 10 8.3 Number of primary packs to be examined . 11 8.4 Test report . 11 9 Batch testing . 11 9.1 General . 11 9.2 Sampling plans . 11 9.3 Un

14、it of product 12 9.4 Non-conformities 12 9.5 Labelling 14 9.6 Test report . 14 9.7 Acceptance or rejection of a batch . 14 9.7.1 Non-conforming units 14 9.7.2 Critical non-conforming units . 14 9.7.3 Major non-conforming units 14 9.7.4 Minor non-conforming units 14 9.7.5 Pyrotechnic articles supplie

15、d in primary packs 14 Annex A (informative) Overview of essential safety requirements and corresponding clauses of all parts of EN 16263 . 15 BS EN 16263-2:2015 EN 16263-2:2015 (E) 3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 200

16、7/23/EC on the placing on the market of pyrotechnic articles 16 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2013/29/EU on the placing on the market of pyrotechnic articles 17 Bibliography 18 BS EN 16263-2:2015 EN 16263-2:2015 (E)

17、4 European foreword This document (EN 16263-2:2015) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorseme

18、nt, at the latest by February 2016, and conflicting national standards shall be withdrawn at the latest by February 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identif

19、ying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA or Annex ZB, wh

20、ich are an integral part of this document. This European standard is one of the series of standards as listed below: EN 16263-1, Pyrotechnic articles Other pyrotechnic articles Part 1: Terminology; EN 16263-2, Pyrotechnic articles Other pyrotechnic articles Part 2: Requirements; EN 16263-3, Pyrotech

21、nic articles Other pyrotechnic articles Part 3: Categories and types; EN 16263-4, Pyrotechnic articles Other pyrotechnic articles Part 4: Test methods; EN 16263-5, Pyrotechnic articles Other pyrotechnic articles Part 5: Minimum labelling requirements and instructions for use. According to the CEN-CE

22、NELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,

23、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16263-2:2015 EN 16263-2:2015 (E) 5 1 Scope This European Standard specifies requirements for the constru

24、ction and performances of other pyrotechnic articles, except pyrotechnic articles for vehicles, ignition devices and cartridges for powder actuated tools (PAT), of the following generic types: flares; flash devices; gas generators; heaters; other cartridges; pyromechanical devices; rockets and rocke

25、t motors; semi-finished pyrotechnic articles; smoke / aerosol generators; sound emitters; pyrotechnic liquid dispersers. This European Standard does not apply for articles containing pyrotechnic compositions that include any of the following substances: arsenic or arsenic compounds; polychlorobenzen

26、es; mercury compounds; lead compounds (except for those included in ignition devices); white phosphorus; picrates or picric acid. This European Standard does not apply to pyrotechnic articles that contain detonative explosives other than black powder and/or flash composition, if these detonative exp

27、losives: can be easily extracted from the pyrotechnic article, or; can initiate secondary explosives, or; can function in a detonative manner although the article is not designed to detonate and the article belongs to the category P2. BS EN 16263-2:2015 EN 16263-2:2015 (E) 6 2 Normative references T

28、he following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16263

29、-1:2015, Pyrotechnic articles Other pyrotechnic articles Part 1: Terminology EN 16263-3:2015, Pyrotechnic articles Other pyrotechnic articles Part 3: Categories and types EN 16263-4:2015, Pyrotechnic articles Other pyrotechnic articles Part 4: Test methods EN 16263-5:2015, Pyrotechnic articles Other

30、 pyrotechnic articles Part 5: Minimum labelling requirements and instructions for use prEN 16265:2013, Pyrotechnic articles Other pyrotechnic articles Ignition devices ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for

31、lot-by-lot inspection 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 16263-1:2015 apply. 4 General and safety requirements 4.1 Incompatible substances Pyrotechnic articles shall not contain incompatible substances as defined in EN 16263-1:2015, 2.2.2

32、3 unless effective measures have been taken to permanently segregate incompatible substances one from the other, effective measures have been taken to stabilize mixtures of incompatible substances, or the manufacturer can demonstrate that any mixtures of incompatible substances do not present a risk

33、 to safety. This requirement shall be verified by examination of the design from the manufacturers documentation. 4.2 Safe disposal Each pyrotechnic article shall be designed and manufactured in such a way that it can be disposed of safely by a suitable process with minimum effect on the environment

34、. This requirement shall be verified by examination of the information about safe disposal in the instructions for use. 4.3 Means of ignition Any means of ignition shall be protected to avoid accidental initiation of the article. This requirement shall be verified by visual examination. For pyrotech

35、nic articles equipped with ignition devices which are CE type certified, no further testing of the ignition devices is required. If the pyrotechnic article is equipped with ignition devices which are not CE type certified, the ignition devices shall comply with the following requirements of prEN 162

36、65:2013: safety features (see 4.5 and prEN 16265:2013, 5.5); BS EN 16263-2:2015 EN 16263-2:2015 (E) 7 mechanical resistance of leading wires (if any) or leading optical fibre (if any) (see prEN 16265:2013, 5.8.1 and 5.8.2); determination of all-fire and no-fire thresholds (see prEN 16265:2013, 5.9);

37、 electrical characteristics (see prEN 16265:2013, 5.11); resistance to ESD (see prEN 16265:2013, 5.12). These tests may be performed on the articles or on subcomponents of the pyrotechnic articles which include their ignition device provided that their functioning remains representative of the norma

38、l behaviour of the ignition device in the article. Manufacturers may provide test reports proving these requirements are fulfilled. 4.4 Safety features Each pyrotechnic article shall be equipped with safety features which are appropriate to its mode of initiation. For articles that are sensitive to

39、mechanical shocks, drops or other stimuli with the potential to cause unintended initiation, if the safety feature is not already a part of the included ignition device, the pyrotechnic article shall be equipped: with a safe / arm device, a safety pin or any other device intended to stop propagation

40、 of ignition along the whole pyrotechnic train; or with other means of protection to prevent inadvertent initiation. The presence of the safety features shall be checked by visual examination and their effectiveness shall be verified in accordance with EN 16263-4:2015, 5.7 (mechanical conditioning),

41、 5.8 (mechanical impact test), and 5.13.1.2 (electrostatic discharge). No initiation shall take place during these tests and the safety features shall remain in their safe position. This last requirement shall be verified by visual examination. Integral safety features shall be checked by verificati

42、on of construction and design according to 5.1 and their effectiveness shall be verified in accordance with EN 16263-4:2015, 5.7 (mechanical conditioning), 5.8 (mechanical impact test), and 5.13.1.2 (electrostatic discharge). No initiation shall take place during these tests and the safety features

43、shall remain in their safe position. This last requirement shall be verified by function test in accordance EN 16263-4:2015, 5.10.3.4. When the user could be exposed to the pyrotechnic effects during the ignition operation, the pyrotechnic article shall be equipped with an appropriate delay to allow

44、 the user to retire to the safe firing distance or assume the safe article orientation for hand-held devices as specified in the instructions for use. This requirement shall be verified according to EN 16263-4:2015, 5.10.3.1 and 5.6. 4.5 Toxicity When the article is designed to generate toxic substa

45、nces as intended use (e.g. pesticides), the manufacturer or importer shall supply corresponding information on the appropriate means of limiting exposure to these reaction products. This requirement shall be verified by examination of the instructions for use. 5 Performance requirements 5.1 Verifica

46、tion of performance When tested in accordance with EN 16263-4:2015, 5.10, each pyrotechnic article shall function completely and attain the performance characteristics specified by the manufacturer. BS EN 16263-2:2015 EN 16263-2:2015 (E) 8 The articles that have been exposed to mechanical conditioni

47、ng (EN 16263-4:2015, 5.7) and/or mechanical impact test (EN 16263-4:2015, 5.8 see list in 5.4 of this standard) and to thermal conditioning (EN 16263-4:2015, 5.9.2.1) shall function safely and completely. When a use by date is specified by the manufacturer and is greater than two years after the man

48、ufacturing of the article, its correct functioning at the use by date shall be demonstrated by the manufacturer: either by results of firings of articles at the use by date where available; or by function test in accordance with EN 16263-4:2015, 5.10, after extension of the thermal conditioning test

49、 over a period of time that shall be determined from the use by date according to EN 16263-4:2015, 5.9.2.4. 5.2 Verification of design When tested in accordance with EN 16263-4:2015, 5.2 and 5.3, the pyrotechnic article shall be in accordance with the manufacturers documentation regarding construction, dimensions, mass and composition of pyrotechnic substances and mixtures, etc. including tolerances as specified by the manufacturer. 5.3 Verification of labell