EN 15432-2008 en Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability (Incorporating Corrigendum June 2010 Remains Current)《冬季公路服务区的维.pdf

《EN 15432-2008 en Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability (Incorporating Corrigendum June 2010 Remains Current)《冬季公路服务区的维.pdf》由会员分享，可在线阅读，更多相关《EN 15432-2008 en Winter and road service area maintenance equipments - Front-mounted equipments - Interchangeability (Incorporating Corrigendum June 2010 Remains Current)《冬季公路服务区的维.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15432:2008Winter and road service area maintenance equipments Front-mounted equipments InterchangeabilityICS 43.160g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g

2、38g50g51g60g53g44g42g43g55g3g47g36g58IncorporatingJune 2010corrigendumNational forewordThis British Standard is the UK implementation of EN 15432:2008, incorporating corrigendum June 2010. The UK participation in its preparation was entrusted by Technical Committee B/513, Construction equipment and

3、plant and site safety, to Panel B/513/-/16, Winter maintenance and road surface and maintenance equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users

4、 are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 15432:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2010Amendments/corrigenda issu

5、ed since publicationDate Comments 30 November 2010Implementation of CEN corrigendum June 2010; replacement of figure 3ISBN 978 0 580 72983 6EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15432January 2008ICS 43.160English VersionWinter and road service area maintenance equipments - Front-mounted

6、equipments - InterchangeabilityMatriels de viabilit hivernale et dentretien desdpendances routires - Matriels monts lavant -InterchangeabilitWinterdienst- und Straenbetriebsdienstausstattung -Mechanische Schnittstelle an Fahrzeugen frfrontangebaute Maschinen - AustauschbarkeitThis European Standard

7、was approved by CEN on 21 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such n

8、ationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and

9、notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

10、alta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of explo

11、itation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15432:2008: EIncorporating corrigendum June 20102 Contents Foreword3 1 Scope.4 2 Normative references.4 3 Interchangeability requirements.4 3.1 Front mounting plate4 3.1.1 General provisions4 3.1.2 Mounting p

12、late classes.5 3.1.3 Strength requirements5 3.1.4 Designation.6 3.1.5 Interchangeability dimensions 6 3.1.6 Tool fixing systems.9 3.2 Electrical and hydraulic connections .9 3.2.1 General.9 3.2.2 Location on the vehicle.10 3.2.3 Clearance space.12 3.2.4 Connection types13 3.2.5 Identification and pr

13、eferred layout of hydraulic connections 13 3.3 Mechanical Power Take Off (PTO) .14 Annex A (normative) Quick-coupling VV95 system for front mounted equipments.16 A.1 General16 A.2 Interchangeability requirements16 A.2.1 Front mounting plate 16 A.2.2 Electrical and hydraulic connections19 A.2.3 Mecha

14、nical Power Take Off (PTO)20 Annex B (normative) Compact F1/C front mounting plate for combined road and off-road applications .21 B.1 General21 B.2 Interchangeability requirements Front Mounting Plate 21 B.2.1 General provisions .21 B.2.2 Mounting plate class 21 B.2.3 Strength requirements .21 B.2.

15、4 Designation 21 B.2.5 Interchangeability dimensions22 B.2.6 Tool fixing systems.23 Bibliography 24 BS EN 15432:2008EN 15432:2008 (E)3 Foreword This document (EN 15432:2008) has been prepared by CEN/TC 337/WG 3 “Interface between tools and vehicle“, the secretariat of which is held by UNI-CUNA, unde

16、r the direction of Technical Committee CEN/TC 337 “Winter maintenance and road service area maintenance equipment“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

17、 latest by July 2008, and conflicting national standards shall be withdrawn at the latest by July 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Bulgaria, Cypru

18、s, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15432:2008EN 15432:2008 (E)4 1 Scope

19、 This European Standard specifies the requirements for the various elements of carrying vehicles to ensure interchangeability between a vehicle and different equipments that are frontally mounted. It specifies certain interchangeability dimensions of the front mounting plate, including its height ab

20、ove the ground, as well as the locations of coupling devices for electrical and hydraulic connections and for mechanical power take off (PTO). This European Standard specifies two different classes of mounting plates in order to cover road vehicles, having a maximum design total mass higher than 3,5

21、 t, of the greatest possible variety (commercial vehicles, multi-purpose vehicles, communal vehicles, ), which are capable of carrying front-mounted equipments for winter maintenance and for road service area maintenance. This European Standard specifies, with regard to electrical and hydraulic conn

22、ections and to PTO, only location areas, clearance spaces and preferred layout in order to ensure interchangeability. Requirements applying to connectors, coupling devices and PTO splines are given in EN 15431. Normative Annex A specifies provisions for an advanced front coupling system that is able

23、 to allow for mounting and demounting equipments without the use of tools. Users having to address specific needs (e.g. extreme weather conditions) may require the vehicle be fitted with such automatic coupling system. Normative Annex B gives provisions for a compact and light front mounting plate i

24、ntended for combined road and off-road applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

25、g any amendments) applies. EN 15431, Winter and road service area maintenance equipments Power system and related controls Interchangeability and performance requirements 3 Interchangeability requirements 3.1 Front mounting plate 3.1.1 General provisions Mounting plates of all classes, as defined in

26、 following 3.1.2, shall be designed and installed to the carrying vehicle to allow for safe and easy tilting of the cabin (if the vehicle has been designed to provide for this facility). Mounting plates of all classes, as defined in following 3.1.2, shall be designed and installed to the carrying ve

27、hicle so as to allow for mounting a front towing hitch (if the vehicle has been designed to provide for this facility). Compliance to this requirement may be achieved in different ways, e.g. by a pivoting or folding mounting plate, by an appropriate non-obstructing design or by provisions for direct

28、 mounting of the hitch to the mounting plate itself. Characteristics of the quick-coupling system designed to allow for mounting and demounting of equipments without the use of tools are given in Annex A. Characteristics of the compact mounting plate designed for combined road and off-road applicati

29、ons are given in Annex B. BS EN 15432:2008EN 15432:2008 (E)5 3.1.2 Mounting plate classes Table 1 gives indications on installation heights and on the recommended range of the maximum design total mass (ISO-M07, item 4.7 of ISO 1176:1990) of the carrying vehicle for each of the two classes of mounti

30、ng plates that are defined in this European Standard. The installation height is measured with the carrying vehicle being at kerb mass (ISO-M06, item 4.6 of ISO 1176:1990) from the ground to the upper edge of the mounting plate, as shown in Figure 2 and Figure 3. Table 1 Installation heights of moun

31、ting plate classes Mounting plate class Height mm Recommended range of carrying vehicle maximum design total mass 1)t F 1 1 000 60 7,5 F 2 870 50 3,5 and 9 1)When mounting plates of classes F1 and F2 are being mounted on vehicles, which are not covered by ISO 1176, recommended ranges as given in the

32、 table may not be applicable. 3.1.3 Strength requirements Mounting plates shall be designed to withstand to the maximum loads and moments that are given in Table 2 for each appropriate class. The values given in Table 2 refer to static loads and moments applied by the greatest variety of equipments

33、(e.g. snow plough, grass cutting machine ) that may be fixed on the mounting plate. Equipments apply static loads and moment when they are being held in a raised position for transportation and transfer purposes. Table 2 Maximum static loads Mounting plate class Vertical load, Fz kN Bending moment,

34、My kNm Torsional moment, Mx kNm F 1 22 22 45 F 2 12 12 18 Loads and moments given in Table 2 refer to the vehicle coordinate system as shown in Figure 1. Mounting plates shall also be able to withstand to foreseeable dynamic forces which may arise when working with equipments having maximum static l

35、oads shown in Table 2. BS EN 15432:2008EN 15432:2008 (E)6 Figure 1 Vehicle coordinate system 3.1.4 Designation Mounting plates meeting the requirements of this European Standard shall be identified by the following information, in the order given: a) reference to this European Standard (EN 15432:200

36、8); b) indication of the mounting plate class. EXAMPLE Mounting plate of class F 2: Mounting plate EN 15432 F 2 3.1.5 Interchangeability dimensions Interchangeability dimensions of mounting plates shall be according to: Figure 2 for Class F 1 mounting plates; Figure 3 for Class F 2 mounting plates.

37、Dimensions not specified in Figure 2 and Figure 3 are left to the discretion of the manufacturer. BS EN 15432:2008EN 15432:2008 (E)7 Dimensions in millimetres Key 1 clearance for claw 2 clearance for swivel bolts 3 clearance for swivel bolt 4 clearance for passing bolt 5 cone 6 clearance for centrin

38、g cone NOTE 1 Additional cut-outs are allowed if the stiffness is not reduced thereby. NOTE 2 Additional elements, which do not conflict with the characteristic dimensions, may be provided to couple in-use implements using different fixing systems. Figure 2 Dimensions for F 1 mounting plates BS EN 1

39、5432:2008EN 15432:2008 (E)8 Dimensions in millimetres Key 1 clearance for claw 2 clearance for swivel bolt 3 clearance for swivel bolt 4 cone 5 clearance for centring cone NOTE 1 Additional cut-outs are allowed if the stiffness is not reduced thereby. NOTE 2 Additional elements, which do not conflic

40、t with the characteristic dimensions, may be provided to couple in-use implements using different fixing systems. Figure 3 Dimensions for F 2 mounting plates BS EN 15432:2008EN 15432:2008 (E)9 3.1.6 Tool fixing systems 3.1.6.1 General To ensure interchangeability with tools already in use, mounting

41、plates defined in this European Standard are designed in such a way as to allow for different fixing systems. The choice of the most appropriate fixing system shall be left to the tool manufacturer and to the user. The following subclauses give a description of all the fixing elements provided by ea

42、ch mounting plate class. Additional fixing elements that do not conflict with the characteristic dimensions given in Figure 2 and Figure 3, i.e., which do not interfere with fixing elements listed in following 3.1.6.2 and 3.1.6.3, may also be provided when there is a need of coupling in-use equipmen

43、ts having widespread fixing systems at National or Regional level. 3.1.6.2 Class F 1 mounting plate Class F 1 mounting plates provide for the following fixing elements: two pockets (centre to centre 630 mm 1 mm, section A-A in Figure 2) as a support for the relevant claws; two couples of lateral slo

44、ts ( 30 mm + 1/-0 mm, centre to centre 910 mm + 0/-2 mm, section B-B in Figure 2) for the relevant swivelling bolts; couple of upper slots ( 30 mm + 1/-0 mm, centre to centre 630 mm 1 mm, section C-C in Figure 2) for the relevant swivelling bolts; two threaded holes (M30, centre to centre 630 mm 1 m

45、m, section D-D in Figure 2) for the relevant passing bolts; two holes ( 82 mm + 1/-0 mm, centre to centre 400 mm 1 mm, section E-E in Figure 2) for the relevant centring cones. When using swivelling bolts, the use of appropriate washers is strongly recommended. 3.1.6.3 Class F 2 mounting plate Class

46、 F 2 mounting plates provide for the following fixing elements: two pockets (centre to centre 630 mm 1 mm, section A-A in Figure 3) as a support for the relevant claws; couple of lateral slots ( 26 mm + 1/-0 mm, centre to centre 720 mm + 0/-2 mm, section B-B in Figure 3) for the relevant swivelling

47、bolts; couple of upper slots ( 26 mm + 1/-0 mm, centre to centre 630 mm 1 mm, section C-C in Figure 3) for the relevant swivelling bolts; two holes ( 82 mm +1/-0 mm, centre to centre 400 mm 1 mm, section D-D in Figure 3) for the relevant centring cones. When using swivelling bolts, the use of approp

48、riate washers is strongly recommended. 3.2 Electrical and hydraulic connections 3.2.1 General Electrical connectors and hydraulic couplings for connecting the equipment to the vehicle shall be provided in the front of the vehicle, as close as possible to the front mounting plate. Electrical and hydr

49、aulic connections on the BS EN 15432:2008EN 15432:2008 (E)10 vehicle can be oriented either forward (towards the front of the vehicle) or outward (towards the sides of the vehicle). 3.2.2 Location on the vehicle The location for electrical and hydraulic connections, with respect to the front mounting plate, shall be in accordance with: Figure 4 and corresponding Table 3 for front-mounted connections (facing forward); Figure 5 and corresponding Table 4 for side-mounted connections (facing outward