EN 14617-9-2005 en Agglomerated stone - Test methods - Part 9 Determination of impact resistance《烧结石料的试验方法 第9部分 耐冲击性测定》.pdf

《EN 14617-9-2005 en Agglomerated stone - Test methods - Part 9 Determination of impact resistance《烧结石料的试验方法 第9部分 耐冲击性测定》.pdf》由会员分享，可在线阅读，更多相关《EN 14617-9-2005 en Agglomerated stone - Test methods - Part 9 Determination of impact resistance《烧结石料的试验方法 第9部分 耐冲击性测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 14617-9:2005 Agglomerated stone Test methods Part 9: Determination of impact resistance The European Standard EN 14617-9:2005 has the status of a British Standard ICS 91.100.15 BS EN 14617-9:2005 This British Standard was published under the authority of the Standards Policy a

2、nd Strategy Committee on 31 March 2005 BSI 31 March 2005 ISBN 0 580 45801 6 National foreword This British Standard is the official English language version of EN 14617-9:2005. The UK participation in its preparation was entrusted to Technical Committee B/545, Natural stone, which has the responsibi

3、lity to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Interna

4、tional Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a Brit

5、ish Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international an

6、d European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issue

7、d. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN146179 March2005 ICS91.100.15 Englishversion AgglomeratedstoneTestmethodsPart9:Determinationof impactresistance PierreagglomreMthodesdessaiPartie9: Dterminationdelnergiederupture Knstlichher

8、gestellterSteinPrfverfahrenTeil9: BestimmungderSchlagfestigkeit ThisEuropeanStandardwasapprovedbyCENon3February2005. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelists

9、andbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguagean

10、dnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Sl

11、ovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.E

12、N146179:2005:EEN 14617-9:2005 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Principle4 4 Apparatus .4 5 Preparation of the specimens 4 6 Test procedure.4 7 Expression of results 5 8 Test report 5 Bibliography 6 EN 14617-9:2005 (E) 3 Foreword This document (EN 14617-9:2005) has b

13、een prepared by Technical Committee CEN/TC 246 “Natural stones”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national s

14、tandards shall be withdrawn at the latest by September 2005. Test methods for agglomerated stones consist of the following: EN 14617-1, Agglomerated stone - Test methods Part 1: Determination of apparent density and water absorption EN 14617-2, Agglomerated stone Test methods Part 2: Determination o

15、f flexural strength (bending) prEN 14617-3, Agglomerated stone - Test methods Part 3: Determination of slipperiness EN 14617-4, Agglomerated stone - Test methods Part 4: Determination of the abrasion resistance EN 14617-5, Agglomerated stone - Test methods Part 5: Determination of freeze and thaw re

16、sistance EN 14617-6, Agglomerated stone - Test methods Part 6: Determination of thermal shock resistance prEN 14617-7, Agglomerated stone Test methods Part 7: Determination of ageing prEN 14617-8, Agglomerated stone Test methods Part 8: Determination of resistance to fixing (dowel hole) EN 14617-9,

17、Agglomerated stone - Test methods Part 9: Determination of impact resistance EN 14617-10, Agglomerated stone Test methods Part 10: Determination of chemical resistance EN 14617-11, Agglomerated stone Test methods Part 11: Determination of linear thermal expansion coefficient EN 14617-12, Agglomerate

18、d stone Test methods Part 12: Determination of dimensional stability EN 14617-13, Agglomerated stone Test methods Part 13: Determination of electrical resistivity prEN 14617-14, Agglomerated stone Test methods Part 14: Determination of surface hardness EN 14617-15, Agglomerated stone Test methods Pa

19、rt 15: Determination of compressive strength EN 14617-16, Agglomerated stone Test methods Part 16: Determination of dimensions, geometric characteristics and surface quality of modular tiles prEN 14617-17, Agglomerated stone Test methods Part 17: Determination of biological resistance According to t

20、he CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

21、bourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14617-9:2005 (E) 4 1 Scope This document specifies a method for determining the impact resistance of agglomerated flat stone products. 2 Normative references The following refer

22、enced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Not applicable. 3 Principle The impact resistance is determined by t

23、he dropping of a spherical steel ball from given increasing heights until the specimen breaks. 4 Apparatus 4.1 A steel sphere with mass of 1,0 kg 0,1 kg and diameter of about 6,3 cm. 4.2 An electromagnet with a ball bearing housing and a switch. 4.3 A vertical stick graduated at 5 cm intervals from

24、0 cm to 120 cm, along which the electromagnet can travel. 4.4 A box of minimum section 40 cm X 40 cm and no less than 30 cm high, containing a bed of dry sand at least 20 cm deep. The sand grain size distribution should be in the 1 mm 1,5 mm range. 5 Preparation of the specimens At least four specim

25、ens should be prepared with 20 cm X 20 cm sides. The sample thickness should be between 0,5 cm and 3 cm and should equal the one of the final product. The main faces must be parallel and with the finishing of the end product (sand blasted, gauged or polished surface) faced to the falling sphere but

26、without any chemical surface treatment. 6 Test procedure Lay the sample in the centre of the box on the bed of sand so that the whole thickness is buried. It should be placed so that the centre of the face with the larger size lies on the vertical passing through the vertical of the sphere. A spirit

27、 level should be used to check that the upper face of the sample lies horizontal. The electromagnet should be attached to the stick at a point corresponding to the 6 cm drop (from the bottom) of the sphere. Switch off the electromagnet and let the sphere fall. The drop height (h) should be measured

28、between the lowest point of the sphere and the impact surface. Repeat the test by progressively increasing the drop height 5 cm at a time until the sample is broken. Any surface damage caused by the steel sphere drop will be visually noticed in comparison with reference specimens, recorded and repor

29、ted in the test results. EN 14617-9:2005 (E) 5 7 Expression of results The fracture work L in joule is expressed by the formula L = M h g where M is the sphere mass in kg; h is the drop height in meters of the sphere which causes the sample to break; g is the gravity acceleration equal to 9,806 m /s

30、 2The final data must be obtained by averaging the results from at least four specimens. 8 Test report The test report shall contain the following information: a) unique identification number of the report; b) number, title and date of issue of this document; c) name and address of the test laborato

31、ry and the address where the test was carried out if different from the test laboratory; d) name and address of the client; e) it is the responsibility of the client to supply the following information: name of the supplier; name of the person or organization which carried out the sampling; surface

32、finish of the specimens (if relevant to the test); nature of the binders f) date of delivery of the sample or of the specimens; g) date when the specimens were prepared and the date of testing; h) number, shape and size of the specimens in the sample; i) any observed damage for each specimen; j) fra

33、cture work value of each specimen and the average value on at least four specimens; k) all deviations from the standard and their justification; l) remarks. The test report shall contain the signature(s) and role(s) of the responsible(s) for the testing and the written consent of the test laboratory

34、. It shall also stated that the report shall not be partially reproduced without the written consent of the test laboratory. EN 14617-9:2005 (E) 6 Bibliography EN 12440, Natural stone - Denomination criteria EN 14618, Agglomerated stone- Terminology and classification blankBS EN 14617-9:2005 BSI 389

35、 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are up

36、dated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

37、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically

38、receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/

39、www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international

40、 standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscri

41、bing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information

42、regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

43、 of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission

44、from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.