EN 14593-1-2018 en Respiratory protective devices - Compressed air line breathing devices with demand valve - Part 1 Devices with a full face mask - Requirements testing and markin.pdf

《EN 14593-1-2018 en Respiratory protective devices - Compressed air line breathing devices with demand valve - Part 1 Devices with a full face mask - Requirements testing and markin.pdf》由会员分享，可在线阅读，更多相关《EN 14593-1-2018 en Respiratory protective devices - Compressed air line breathing devices with demand valve - Part 1 Devices with a full face mask - Requirements testing and markin.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Respiratory protective devices - Compressed air line breathing devices with demand valvePart 1: Devices with a full face mask - Requirements, testing and markingBS EN 14593-1:2018National forewordThis British Standard i

2、s the UK implementation of EN 14593-1:2018. It supersedes BS EN 14593-1:2005, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PH/4, Respiratory protection.A list of organizations represented on this committee can be obtained on request to its secretary

3、.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 95721 5ICS 13.340.30Compliance with a British Standard cannot conf

4、er immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 14593-1:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORME

5、N 14593-1May 2018ICS 13.340.30 Supersedes EN 14593-1:2005EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 14593-1:2018: EAll rights of exploitation in any form and b

6、y any means reserved worldwide for CEN national MembersRespiratory protective devices - Compressed air line breathing devices with demand valve - Part 1: Devices with a full face mask - Requirements, testing and markingAppareils de protection respiratoire - Appareils de protection respiratoire isola

7、nts adduction dair comprim avec soupape la demande - Partie 1: Appareil avec masque complet - Exigences, essais et marquageAtemschutzgerte - Druckluft-Schlauchgerte mit Lungenautomat - Teil 1: Gerte mit einer Vollmaske - Anforderungen, Prfung und KennzeichnungThis European Standard was approved by C

8、EN on 16 March 2018.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

9、may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified

10、 to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland

11、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 14593-1:2018 (E)European foreword .iv1 Scope . 52 Normative references 53 Terms, description and

12、 symbols 63.1 Terms . 63.2 Description . 63.3 Symbols . 64 Requirements 64.1 General . 64.2 Nominal values and tolerances . 74.3 Ergonomics 74.4 Materials . 74.5 Practical performance 74.6 Connections . 84.6.1 General 84.6.2 Couplings 84.6.3 Strength of connections to full face mask, demand valve, m

13、edium pressure connecting tube and breathing hose 84.6.4 Connection between RPD and full face mask 84.6.5 Unacceptable connections . 84.7 Compressed air line breathing device used with self-contained breathing device - switch over device 94.7.1 General 94.7.2 Switch over warning device . 94.8 Body h

14、arness or belt . 104.9 Pre-conditioning . 104.10 Flammability 104.11 Resistance to pressure . 104.12 RPD with mobile high pressure air supply systems 104.12.1 General. 104.12.2 Pressure reducer .114.12.3 Pressure reducer relief valve 114.13 Warning devices for mobile high pressure air supply systems

15、 114.13.1 General. 114.13.2 Audible warning device 114.14 Compressed air supply tube . 124.14.1 Resistance to kinking 124.14.2 Resistance to collapse .124.14.3 Strength 124.14.4 Flexibility . 124.14.5 Heat resistance .124.14.6 Electrostatic properties 124.14.7 Couplings . 124.15 Breathing hose . 134

16、.15.1 Resistance to kinking 134.15.2 Resistance to collapse .134.16 Lung governed demand valve . 134.16.1 Without positive pressure 134.16.2 With positive pressure .134.16.3 Supplementary air supply . 134.16.4 Couplings . 134.17 Adjustable parts 144.18 Full face masks . 14iiContents PageBS EN 14593-

17、1:2018EN 14593-1:2018 (E)4.19 Total inward leakage . 144.20 Breathing resistance . 144.20.1 General. 144.20.2 Inhalation resistance .144.20.3 Exhalation resistance 144.21 Carbon dioxide content of inhalation air . 154.22 Leaktightness 155 Testing 155.1 General 155.2 Inspection . 165.3 Practical perf

18、ormance . 175.3.1 General. 175.3.2 Preparation of RPD to be tested 175.3.3 Test conditions175.3.4 Work simulation test .175.3.5 Information to be recorded . 185.3.6 Practical performance tests at low temperature.185.4 Strength of connections to facepiece, demand valve, medium pressure connecting tub

19、e and breathing hose 185.5 Resistance to collapse of breathing hose . 195.5.1 Principle . 195.5.2 Apparatus 195.5.3 Procedure 195.6 Strength of compressed air supply tube, body harness and couplings .205.7 Pre-conditioning . 215.8 Flammability 215.9 Pressure relief valve 215.10 Resistance to kinking

20、 of compressed air supply tube 215.11 Resistance to collapse of compressed air supply tube 245.11.1 Principle . 245.11.2 Apparatus 245.11.3 Procedure 245.12 Heat resistance of compressed air supply tube . 245.13 Tests for lung-governed demand valve . 255.13.1 Without positive pressure 255.13.2 With

21、positive pressure .255.13.3 Supplementary air supply . 255.14 Determination of carbon dioxide content of the inhalation air .265.15 Testing of audible warning device . 265.16 Switch over device 275.17 Leaktightness 275.18 Sound level measurement 276 Marking .287 Information supplied by the manufactu

22、rer 28Annex ZA (informative) Annex ZA Relationship between this European Standard and the essential health and safety requirements of Regulation 2016/425/EU 2016 OJ L81 aimed to be covered30Bibliography .32 ISO ISO pub-date year All rights reserved iiiBS EN 14593-1:2018EN 14593-1:2018 (E)European fo

23、rewordThis document (EN 14593-1:2018) has been prepared by Technical Committee CEN/TC 79 “Respiratory protective devices”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

24、 the latest by November 2018, and conflicting national standards shall be withdrawn at the latest by November 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent

25、rights.This document supersedes EN 14593-1:2005.This document has been prepared under a standardization request given to CEN by the European Commission and the European Free Trade Association, and supports essential health and safety requirements of EU Regulation(s).For relationship with EU Regulati

26、on(s) see informative Annex ZA, which is an integral part of this document.The following main technical changes have been made compared to EN 14593-1:2005:a) requirements for cleaning and disinfection deleted;b) visual inspection changed to inspection and detailed list inserted;c) test for leaktight

27、ness added;d) test for noise level adapted to the test procedure specified in ISO 16900-14;e) Annex B deleted;f) figures adapted to the changes made in the test procedures, where appropriate.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun

28、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po

29、land, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.ivBS EN 14593-1:2018EN 14593-1:2018 (E)1 ScopeThis document specifies minimum requirements for compressed air line breathing devices with demand valve for use with a full face mask as a res

30、piratory protective device (RPD).Diving RPD are not covered by this document.RPD used in abrasive blasting operations without additional protective features are not covered by this document.Escape RPD, although certain requirements addressing the use in conjunction with escape RPD and escape conditi

31、ons are given, are not covered by this document.Laboratory and practical performance tests are included for the assessment of conformance to the requirements.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirem

32、ents of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 132:1998, Respiratory protective devices Definitions of terms and pictogramsEN 134:1998, Respiratory protective dev

33、ices Nomenclature of componentsEN 136:1998, Respiratory protective devices Full face masks Requirements, testing, markingEN 137:2006, Respiratory protective devices Self-contained open-circuit compressed air breathing apparatus with full face mask Requirements, testing, markingEN 148-1, Respiratory

34、protective devices Threads for facepieces Part 1: Standard thread connectionEN 148-2, Respiratory protective devices Threads for facepieces Part 2: Centre thread connectionEN 148-3, Respiratory protective devices Threads for facepieces Part 3: Tread connection M 45 x 3EN 402:2003, Respiratory protec

35、tive devices Lung governed demand self-contained open-circuit compressed air breathing apparatus with full face mask or mouthpiece assembly for escape Requirements, testing, markingEN 12021, Respiratory equipment Compressed gases for breathing apparatusEN 13274-1:2001, Respiratory protective devices

36、 Methods of test Part 1: Determination of inward leakage and total inward leakageEN 13274-2:2001, Respiratory protective devices Methods of test Part 2: Practical performance testsEN 13274-3:2001, Respiratory protective devices Methods of test Part 3: Determination of breathing resistanceEN 13274-4:

37、2001, Respiratory protective devices Methods of test Part 4: Flame testsEN 13274-6, Respiratory protective devices Methods of test Part 6: Determination of carbon dioxide content of the inhalation airEN ISO 8031, Rubber and plastics hoses and hose assemblies Determination of electrical resistance an

38、d conductivity (ISO 8031)ISO 16900-14, Respiratory protective devices Methods of test and test equipment Part 14: Measurement of sound level5BS EN 14593-1:2018EN 14593-1:2018 (E)3 Terms, description and symbolsFor the purposes of this document, the terms, definitions and symbols given in EN 132:1998

39、, EN 134:1998 and the following apply.3.1 Terms3.1.1as receivednot pre-conditioned or modified to carry out a test3.1.2facepieceRespiratory Interface (RI)full face mask conforming to EN 136 (Class 2 or Class 3)3.1.3mobile high pressure air supply systemsupply system that can include a compressor, fi

40、lters, compressed air cylinders, for use as a mobile source of breathable air3.1.4switch over devicedevice that ensures that in the event of a malfunction or disconnection of the airline, the air supply, when airline is used in conjunction with self-contained breathing devices, automatically switche

41、s over to the self contained air supply, without interruption of supplied air to the wearer3.2 DescriptionThis RPD supplies the wearer with breathable air in accordance with EN 12021, which on inhalation, flows through a lung governed demand valve. The latter can operate at negative pressure or at p

42、ositive pressure and is connected to a suitable full face mask, possibly via a breathing hose. A compressed air supply tube connects the wearer to a supply of compressed air. Exhaled air flows into the ambient atmosphere via an exhalation valve.NOTE Conformance to EN 12021 can be ensured by a breath

43、able air supply system or an additional device such as a compressed air filter system.3.3 Symbols3.3.1See information supplied by the RPD manufacturer4 Requirements4.1 GeneralAll test samples specified in the related test clauses shall meet the relevant requirements.Where it is required in a specifi

44、c clause, the manufacturer shall declare that a risk assessment e.g. a Failure Modes and Effect Analysis (FMEA) concerning these specific requirements has been conducted.NOTE Further information is given in EN 60812 3.6 BS EN 14593-1:2018EN 14593-1:2018 (E)If the manufacturer claims that the RPD may

45、 be used in potentially explosive atmospheres it shall comply with the appropriate requirements.4.2 Nominal values and tolerancesUnless otherwise specified, the values stated in this document are expressed as nominal values. Except for temperature limits, values which are not stated as maxima or min

46、ima shall be subject to a tolerance of 5 %. Unless otherwise specified, the ambient conditions for testing shall be between 16 C and 32 C and (50 30) % relative humidity. Any temperature limits specified shall be subject to an accuracy of 1C.4.3 ErgonomicsThe requirements of this document are intend

47、ed to take account of the interaction between the wearer, the RPD, and where possible the working environment in which the RPD is likely to be used. The RPD shall satisfy 4.4 and 4.8 .Testing shall be performed accordance with 5.3.4.4 Materials4.4.1 All materials used in the construction shall have

48、adequate resistance to deterioration by heat and adequate mechanical strength.After any pre-conditioning according to 5.7, testing shall be performed in accordance with 5.3.The manufacturer shall supply a declaration that this was addressed by a risk assessment, e.g. a FMEA.Check in accordance with

49、5.2.4.4.2 If the manufacturer claims that the RPD may be used in potentially explosive atmospheres, exposed parts, i.e. those which can be subjected to impact during use of the RPD shall not be made of aluminium, magnesium, titanium or their alloys.The manufacturer shall supply a declaration that this was addressed by a risk assessment, e.g. a FMEA.Check in accordance with 5.2.4.4.3 Materials that can come into direct contact with the wearers skin or that can affect the quality of the breathed air sh