EN 112001-1991 en Blank Detail Specification Image Converter and Image Intensifier Tubes《空白详细规范 图象转换器和图象增强管》.pdf

《EN 112001-1991 en Blank Detail Specification Image Converter and Image Intensifier Tubes《空白详细规范 图象转换器和图象增强管》.pdf》由会员分享，可在线阅读，更多相关《EN 112001-1991 en Blank Detail Specification Image Converter and Image Intensifier Tubes《空白详细规范 图象转换器和图象增强管》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 112001:1997 Incorporating Amendment No.1to BSCECC12001:1980 (renumbers BS as BSEN112001:1997) Harmonized system of quality assessment for electronic components Blank detail specification: Image converter and image intensifier tubes The European Standard EN112001:1991 has the s

2、tatus of a BritishStandard ICS 31.100BSEN112001:1997 BSI04-2000 ISBN 058034941 1 National foreword This BritishStandard has been prepared by Technical Committee EPL/39and is the English language version of EN112001:1991 Harmonized system of quality assessment for electronic components Blank detail s

3、pecification: Image converter and image intensifier tubes, published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). Cross-references The BritishStandards which implement international or European publications referred to in this docum

4、ent may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of Briti

5、sh Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to8 and a back cover. This s

6、tandard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN112001:1997 BSI 04-2000 i Contents Page National foreword Inside front cover

7、Foreword 2 Text of EN112001 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN112001 December 1991 UDC: Descriptors: Quality, electronic components, tubes English version Blank Detail Specification: Image converter and image intensifier tubes Spcification Particulire Cadre: Tubes converti

8、sseurs dimage et tubes intensificateurs dimage Vordruck fr Bauartspezifikation: Eine deutsche Version liegt zur Zeit nicht vor* This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on 20November1991. The text of this standard consists of the text of CECC12001 Iss

9、ue11980 of the corresponding CECC Specification. CENELEC members are bound to comply with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concer

10、ning such national standards may be obtained on application to the General Secretariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German*). A version in any other language made by translation under the responsibility of a CENELEC

11、member into its own language and notified to the CECC General Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norwa

12、y, Portugal, Spain, Sweden, Switzerland, and UnitedKingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrote

13、chnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1991 Copyright reserved to CENELEC members Ref. No. EN112001:1991 EEN112001:1991 BSI 04-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member cou

14、ntries of the European Committee for Electronical Standardization (CENELEC) who wish to take part in a harmonized system for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment proc

15、edures for electronic components and by the grant of an internationally recognised Mark, or Certificate, of Conformity. The components produced under the System are thereby accepted by all member countries without further testing. This document has been formally approved by the CECC, and has been pr

16、epared for those member countries taking part in the System who wish to issue national harmonized specifications for IMAGE CONVERTER AND IMAGE INTENSIFIER TUBES. It should be read in conjunction with document CECC00100: Basic Rules (1974). Preface This blank detail specification was proposed by CECC

17、 Working Group11: “ELECTRO-OPTICAL DEVICES”. It is a blank detail specification for image converter and image intensifier tubes relating to the generic specification printed as CECC12000. The text of this specification was circulated to the CECC, for voting, in document CECC(Secretariat)381in July19

18、75, and following ratification of the Report on the Voting in CECC(Secretariat)555in December1976 was approved by the CECC Management Committee for printing as a CECC Specification. It is recognised that the layout proposed cannot be applied to all detail specifications based on this document. The C

19、ECC Management Committee at its meeting in Copenhagen in March1979 decided that as the German National Authorized Institution would not be implementing the requirements of this CECC generic specification, the text should be published in the English and French versions only. Contents Page Foreword 2

20、Appendix A Inspection drawing 8 Appendix B Blemish specification 8EN112001:1991 BSI 04-2000 3 Key for page4 The numbers between square brackets on page4 correspond to the following indications which should be given: Identification of the detail specification Identification of the component NOTEWhen

21、a device is so designed that it can satisfy several applications, this should be stated in the detail specification, in which case the characteristics and inspection requirements relevant to these applications should be met simultaneously (these may appear in different columns of a detail specificat

22、ion or in different detail specifications, as the case may be). 1 The name of the National Standards Organization under whose authority the detail specification is drafted 2 The CECC Symbol and the number allotted to the national detail specification by the CECC General Secretariat 3 The number and

23、issue number of the national generic and sectional specifications 4 The national number of the detail specification, date of issue and any further information required by the national system, together with any amendment numbers if issued. 5 A short description of the type of component 6 Information

24、on typical construction (where applicable) 7 Outline drawing and/or reference to the relevant document outlines 8 Application or group of applications covered (seenote below) 9 Reference data on the most important properties, to allow comparison between the various component types.EN112001:1991 4 BS

25、I 04-2000 1 2 page: of: CECC 12001XXX ELECTRONIC COMPONENT OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 4 DETAIL SPECIFICATION FOR:IMAGE CONVERTER TUBE or IMAGE INTENSIFIER TUBE 5 DESCRIPTION and CONSTRUCTION Number of stages Type of stages (state if channel multiplier) Integral or non-integral power s

26、upply Windows (fibre optic or plain) Overall gain Phosphor colour and persistence Photocathode type Useful photocathode diameter Useful screen diameter Magnification 6 OUTLINE DRAWING SHOWING: 7 8 (not for inspection purposes) Overall length APPLICATION(S) Diameter Terminal identification Positions

27、of photocathode and screen Optical axes LEVEL OF QUALITY ASSESSMENT DATA (not for inspection purposes) Mechanical Mounting position and accessories Mass (weight) a Environmental (where appropriate) Limiting values (absolute maximum rating system IEC134) 9 Instantaneous input supply voltage(s) Contin

28、uous input supply voltage(s) Supply frequency(ies) for tubes with a.c.input Photocathode illuminance/irradiance a Storage temperature Storage temperature of specified duration (short term) Operating temperature of specified duration (ambient, short term) Min. a a a a Max. a a a a a a a Unit V V Hz a

29、 C C C Seethe relevant Qualified Products List for availability of components qualified under this detail specification. a denotes that a value or unit shall be inserted in the detail specification unless precluded by the design of the tube.EN112001:1991 BSI 04-2000 5 Operating conditions and charac

30、teristics When the tube is operated under the conditions given below, the characteristic values which follow them are attainable: Marking See2.4 of CECC12000. Ordering Information Related documents Structural similarity X-radiation (if applicable) Additional information Tube discharge procedure (if

31、applicable) Test conditions and inspection requirements These are given in the following tables. The test conditions to be used shall be specified in the detail specification as required for a given type, in line with the requirements given in CECC12000 for the relevant test. All references to claus

32、e numbers are made with respect to CECC12000, unless otherwise stated. Operating supply voltage(s) a Supply frequency(ies) for tubes with a.c.input a Ambient temperature a C Min. Max. Unit Gain a a Photocathode luminous sensitivity or absolute spectral sensitivityatspecified wavelengths a a Resoluti

33、on a lp/mm Equivalent background input (EBI) a a Magnification a a a denotes that a value or unit shall be inserted in the detail specification unless precluded by the design of the tube.EN112001:1991 6 BSI 04-2000GROUP A Lot by lot Overall test conditions (except when modified under “Conditions of

34、test”). Supply voltage(s) a Frequency of supply voltage(s) for tubes with a.c.input a Ambient temperature a C a C Test equipment (See4.3 of CECC12000) Focusing system for magnetically focused tubes All potentials with respect to a All tests are non-destructive AQL: given in% Inspection or Test Refer

35、ence CECC12000 Conditions of test Inspection requirements Min Max Units IL AQL SUB-GROUP A1 100% Visual inspection 4.4 As specified 4.4 Photocathode sensitivity Equivalent background input (EBI) Gain 4.6.1 4.6.2 4.6.3 As specified As specified As specified a a a a a a Output luminance uniformity Res

36、olution Gas test Spurious output Blemishes 4.6.5 4.6.12 4.6.14 4.6.15 4.6.16 As specified As specified As specified As specified As specified 4.6.5 4.6.12 4.6 14 4.6.15 Seeblemish specification (Appendix B) a denotes that a value or unit shall be inserted in the detail specification unless precluded

37、 by the design of the tube. GROUP B Lot by lot General test conditions as for Group A Only tests marked D are destructive. AQL: given in% Inspection or Test Reference CECC12000 Conditions of test Inspection requirements Min Max Units IL AQL Dimensions, major 4.5 See4.5 Seeinspection drawing (Appendi

38、x A) S4 4,0 If the specification writer includes additional tests which are destructive tests, these shall be marked (D).EN112001:1991 BSI 04-2000 7GROUP C Periodic General test conditions as for Group A Only tests marked D are destructive. AQL: given in% Inspection or Test Reference CECC12000 Condi

39、tions of test Inspection requirements Min Max Units IL AQL SUB GROUP C1 Periodicity up to three months Detail dimensions Useful photocathode diameter 4.5 4.6.19 See4.5 As specified Seeinspection drawing (Appendix A) 4.6.19 1 4,0 If the detail specification includes additional tests which are destruc

40、tive tests, these shall be marked (D). GROUP D Qualification approval only General test conditions as for Group A The sample size and acceptance criteria are given in 3.3 and 3.4. Only tests marked (D) are destructive Inspection or Test Reference CECC12000 Conditions of test Inspection requirements

41、Min Max Units IL AQL Image alignment Magnification Magnification distortion “S” distortion Operating endurance (D) Post endurance tests 1) Gain 2) Equivalent background input 3) Gas test 4.6.9 4.6.17 4.6.18 4.6.21 4.9.3 4.6.3 4.6.2 4.6.14 As specified As specified As specified As specified Operating

42、 conditions a Switched or continuous Operating hours aortotalnumber of cycles (if switched) As in A1 As in A1 As in A1 a a a a a a a mm % deg a a See3.3 and 3.4. 4.6.14 If the detail specification includes additional tests which are destructive tests, these shall be marked (D). a denotes that a valu

43、e or unit shall be inserted in the detail specification unless precluded by the design of the tube.EN112001:1991 8 BSI 04-2000 Appendix A Inspection drawing An inspection drawing shall be included in the detail specification. The input and output optical axes shall be shown on the drawing. A table o

44、f dimensions shall be included showing the allocation of dimensions to the test groups. These dimensions shall include those essential to both mechanical and optical interchangeability. Appendix B Blemish specification A complete blemish specification shall be included in the detail specification an

45、d shall include, for example the following: Minimum contrast of a blemish to the immediately adjacent area of the image Rules for defining the size of all shapes of blemishes Rules for classifying a cluster of small blemishes Rules for classifying the equivalent size of groups of closely spaced blem

46、ishes Definitions of the shape, size and location on the screen of the quality zones A table of the maximum number of blemishes of each size range permitted in each quality zone.blankBS EN 112001:1997 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent nati

47、onal body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the

48、latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of whic

49、h can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, i