EN 856-2015 en Rubber Hoses and Hose Assemblies - Rubber-Covered Spiral Wire Reinforced Hydraulic Type - Specification《橡胶软管和软管组件 橡胶覆盖钢丝增强液压型 分类》.pdf

《EN 856-2015 en Rubber Hoses and Hose Assemblies - Rubber-Covered Spiral Wire Reinforced Hydraulic Type - Specification《橡胶软管和软管组件 橡胶覆盖钢丝增强液压型 分类》.pdf》由会员分享，可在线阅读，更多相关《EN 856-2015 en Rubber Hoses and Hose Assemblies - Rubber-Covered Spiral Wire Reinforced Hydraulic Type - Specification《橡胶软管和软管组件 橡胶覆盖钢丝增强液压型 分类》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 856:2015Rubber hoses and hoseassemblies Rubber-coveredspiral wire reinforced hydraulictype SpecificationBS EN 856:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 856:2015.It supersedes BS EN 856:1997 which is withdrawn.BSI, as

2、 a member of CEN, is obliged to publish EN 853 as a British Standard. However, attention is drawn to the fact that duringthe development of this European Standard, the UK committeevoted against its approval as a European Standard. This is due to concerns about the abrasion test method detailed inAnn

3、ex A (normative). It is the opinion of the UK committee that theabrasion test method is not reliable and gives inconsistent results.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations repres

4、ented on this committee can be obtainedon request to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 7

5、6536 0ICS 23.040.70 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 May 2015.Amendments/corrigenda issued since publicationDate Text affectedBS EN 856:2015EURO

6、PEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 856 April 2015 ICS 23.100.40 Supersedes EN 856:1996English Version Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature hlicodale de

7、fils mtalliques - Spcification Gummischluche und -schlauchleitungen - Hydraulikschluche mit Drahtspiraleinlage - Spezifikation This European Standard was approved by CEN on 31 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

8、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

9、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

10、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

11、n, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide

12、 for CEN national Members. Ref. No. EN 856:2015 EBS EN 856:2015EN 856:2015 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Types of hose .5 4 Materials and construction .5 4.1 Hoses 5 4.2 Hose assemblies 5 5 Dimensions .5 5.1 Diameters and concentricity .5 5.2 Length .7 5.2.1 Hos

13、es 7 5.2.2 Hose assemblies 7 6 Requirements .8 6.1 Hydrostatic requirements .8 6.2 Minimum bend radius 8 6.3 Impulse test requirements 9 6.4 Leakage of hose assemblies 9 6.5 Cold flexibility 9 6.6 Adhesion between components .9 6.7 Abrasion resistance 9 6.8 Fluid resistance9 6.8.1 Test pieces .9 6.8

14、.2 Oil resistance 10 6.8.3 Water based fluid resistance . 10 6.8.4 Water resistance . 10 6.9 Ozone resistance 10 7 Designation . 10 8 Marking 10 8.1 Hoses . 10 8.2 Hose assemblies . 11 Annex A (normative) Procedure for the measurement of abrasion 12 A.1 Apparatus 12 A.2 Method . 13 A.3 Test pieces 1

15、3 A.4 Condition of test pieces . 13 A.5 Procedure 14 A.6 Expression of results . 14 A.7 Test report . 14 Annex B (normative) Type and routine testing of production hoses . 16 Annex C (informative) Production acceptance testing . 17 BS EN 856:2015EN 856:2015 (E)BS EN 856:2015EN 856:2015 (E) 2 Content

16、s Page Foreword 3 1 Scope 4 2 Normative references 4 3 Types of hose .5 4 Materials and construction .5 4.1 Hoses 5 4.2 Hose assemblies 5 5 Dimensions .5 5.1 Diameters and concentricity .5 5.2 Length .7 5.2.1 Hoses 7 5.2.2 Hose assemblies 7 6 Requirements .8 6.1 Hydrostatic requirements .8 6.2 Minim

17、um bend radius 8 6.3 Impulse test requirements 9 6.4 Leakage of hose assemblies 9 6.5 Cold flexibility 9 6.6 Adhesion between components .9 6.7 Abrasion resistance 9 6.8 Fluid resistance9 6.8.1 Test pieces .9 6.8.2 Oil resistance 10 6.8.3 Water based fluid resistance . 10 6.8.4 Water resistance . 10

18、 6.9 Ozone resistance 10 7 Designation . 10 8 Marking 10 8.1 Hoses . 10 8.2 Hose assemblies . 11 Annex A (normative) Procedure for the measurement of abrasion 12 A.1 Apparatus 12 A.2 Method . 13 A.3 Test pieces 13 A.4 Condition of test pieces . 13 A.5 Procedure 14 A.6 Expression of results . 14 A.7

19、Test report . 14 Annex B (normative) Type and routine testing of production hoses . 16 Annex C (informative) Production acceptance testing . 17 BS EN 856:2015EN 856:2015 (E) 3 Foreword This document (EN 856:2015) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose

20、 assemblies”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015 and conflicting national standards shall be withdrawn at the latest by October 2

21、015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 856:1996. In comparison with EN 856:1996, the followi

22、ng significant changes have been made: updated normative references; tolerances for inside diameter in Table 1; added Annex A; added Annex B; added Annex C. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this

23、European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,

24、 Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 856:2015EN 856:2015 (E)BS EN 856:2015EN 856:2015 (E) 4 1 Scope This European Standard specifies requirements for four types of rubber-covered spiral wire reinforced hydraulic hoses and hose assemblies of nominal bore from 6

25、to 51: Types 4SP, 4SH, R12 and R13. They are all suitable for use with: hydraulic fluids in accordance with ISO 6743-4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from 40 C to +100 C for types 4SP and 4SH and 40 C to +120 C for types R12 and R13; water based fluids at temper

26、atures ranging from 40 C to 70 C; water fluids at temperatures ranging from 0 C to 70 C. This European Standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE 1 The hoses are not suitable for use with castor oil based nor ester bas

27、ed fluids. NOTE 2 Hoses and hose assemblies are not be operated outside the limits of this standard. NOTE 3 Requirements for hydraulic hoses for underground mining are standardised in a separate standard. 2 Normative references The following documents, in whole or in part, are normatively referenced

28、 in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 1302, Geometrical Product Specifications (GPS) - Indication of surface t

29、exture in technical product documentation (ISO 1302) EN ISO 1402:2009, Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009) EN ISO 4671, Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies

30、 (ISO 4671) EN ISO 6743-4, Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4) EN ISO 6803, Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803) EN ISO 7326, Rubber and pl

31、astics hoses - Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8033:2006, Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2006) EN ISO 10619-2, Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bendin

32、g tests at sub-ambient temperatures (ISO 10619-2) ISO 1817:2005, Rubber, vulcanized - Determination of the effect of liquids ISO 23529, Rubber - General procedures for preparing and conditioning test pieces for physical test methods BS EN 856:2015EN 856:2015 (E)BS EN 856:2015EN 856:2015 (E) 4 1 Scop

33、e This European Standard specifies requirements for four types of rubber-covered spiral wire reinforced hydraulic hoses and hose assemblies of nominal bore from 6 to 51: Types 4SP, 4SH, R12 and R13. They are all suitable for use with: hydraulic fluids in accordance with ISO 6743-4 with the exception

34、 of HFD R, HFD S and HFD T at temperatures ranging from 40 C to +100 C for types 4SP and 4SH and 40 C to +120 C for types R12 and R13; water based fluids at temperatures ranging from 40 C to 70 C; water fluids at temperatures ranging from 0 C to 70 C. This European Standard does not include requirem

35、ents for end fittings. It is limited to the performance of hoses and hose assemblies. NOTE 1 The hoses are not suitable for use with castor oil based nor ester based fluids. NOTE 2 Hoses and hose assemblies are not be operated outside the limits of this standard. NOTE 3 Requirements for hydraulic ho

36、ses for underground mining are standardised in a separate standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references

37、, the latest edition of the referenced document (including any amendments) applies. EN ISO 1302, Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302) EN ISO 1402:2009, Rubber and plastics hoses and hose assemblies - Hydrostatic testin

38、g (ISO 1402:2009) EN ISO 4671, Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 6743-4, Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic syst

39、ems) (ISO 6743-4) EN ISO 6803, Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803) EN ISO 7326, Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8033:2006, Rubber and plastics hoses - Determinat

40、ion of adhesion between components (ISO 8033:2006) EN ISO 10619-2, Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2) ISO 1817:2005, Rubber, vulcanized - Determination of the effect of liquids ISO 23529, R

41、ubber - General procedures for preparing and conditioning test pieces for physical test methods BS EN 856:2015EN 856:2015 (E) 5 3 Types of hose Four types of hose are specified: 1) Type 4SP a 4-steel wire spiral medium pressure hose; 2) Type 4SH a 4-steel wire spiral extra high pressure hose; 3) Typ

42、e R12 a 4 steel wire spiral heavy duty high temperature hose medium pressure rating; 4) Type R13 a multiple steel wire spiral heavy duty high temperature hose high pressure rating. 4 Materials and construction 4.1 Hoses Hoses shall consist of an oil and water resistant synthetic rubber lining, spira

43、l plies of steel wire wrapped in alternating directions, and an oil and weather resistant synthetic rubber cover. Each spiral wire ply shall be separated by an insulating layer of synthetic rubber. 4.2 Hose assemblies Hose assemblies shall only be manufactured with those hose fittings whose function

44、ality has been verified in accordance with subclauses 6.1, 6.3, 6.4 and 6.5 of this European Standard. 5 Dimensions 5.1 Diameters and concentricity When measured in accordance with EN ISO 4671, the diameters of the hoses shall conform to the values given in Table 1. Table 1 Diameters of hoses Dimens

45、ions in millimetres, except nominal bore Nominal bore Inside diameter Type 4SP Type 4SH Type R12 Type R13 min. max. min. max. min. max. min. max. 6 6,2 7,0 - - - - - - 10 9,4 10,1 - - 9,3 10,1 - - 12 12,6 13,5 - - 12,3 13,5 - - 16 15,8 16,7 - - 15,5 16,7 - - 19 18,8 19,8 19,1 19,8 18,6 19,8 18,6 19,

46、8 25 25,4 26,4 25,5 26,4 25,0 26,4 25,0 26,4 31 31,8 33,0 32,0 33,0 31,4 33,0 31,4 33,0 38 38,0 39,3 38,2 39,3 37,7 39,3 37,7 39,3 51 50,6 52,0 50,6 52,0 50,4 52,0 50,4 52,0 When measured in accordance with EN ISO 4671, the diameter over reinforcement and outside diameter of the hoses shall conform

47、to the values given in Table 2. BS EN 856:2015EN 856:2015 (E)BS EN 856:2015EN 856:2015(E)6Table2 Diameteroverreinforcementandoutside diameterDimensionsin millimetres,exceptnominalboreNominal boreType4SPType4SHTypeR12TypeR13DiameteroverreinforcementOutside diameterofhoseDiameteroverreinforcementOutsi

48、de diameterofhoseDiameteroverreinforcementOutside diameterofhoseDiameteroverreinforcementOutside diameterofhosemin.max.min.max.min.max.min.max.min.max.min.max.min.max.min.max.614,115,317,118,7-1016,918,120,622,2-16,617,819,521,0-1219,421,023,825,4-19,921,523,024,6-1623,024,627,429,0-23,825,426,628,8

49、-1927,429,031,433,027,629,231,433,026,928,429,931,528,229,831,033,22534,536,138,540,934,436,037,539,934,135,736,839,234,936,437,639,83145,047,049,252,440,942,943,947,142,745,145,448,645,648,048,351,33851,453,455,658,847,849,851,955,149,251,651,955,053,155,555,858,85164,366,368,271,462,264,266,569,762,564,865,168,366,969,369,572,7BS EN 856:2015 EN 856:2015 (E)BS EN 856:2015EN 856:2015(E)6Table2 Diameteroverreinforcementandoutside diameterDimensionsin millimetres,exceptnominalboreNominal