EN 845-1-2013 en Specification for ancillary components for masonry - Part 1 Wall ties tension straps hangers and brackets (Incorporates Amendment A1 2016)《砌体用辅助部件规格 第1部分 壁锚 拉力带 吊架.pdf

《EN 845-1-2013 en Specification for ancillary components for masonry - Part 1 Wall ties tension straps hangers and brackets (Incorporates Amendment A1 2016)《砌体用辅助部件规格 第1部分 壁锚 拉力带 吊架.pdf》由会员分享，可在线阅读，更多相关《EN 845-1-2013 en Specification for ancillary components for masonry - Part 1 Wall ties tension straps hangers and brackets (Incorporates Amendment A1 2016)《砌体用辅助部件规格 第1部分 壁锚 拉力带 吊架.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 845-1:2013Specification for ancillarycomponents for masonryPart 1: Wall ties, tension straps, hangersand bracketsBS EN 845-1:2013Incorporating corrigendum September 2013BS EN 845-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of

2、EN 845-1:2013. Itsupersedes BS EN 845-1:2003+A1:2008 which is withdrawn.EN 845-1 specifies the characteristics and performance requirementsfor ties, joist hangers, straps and brackets available throughout theCEN member countries. It aims to do so in product performanceterms, avoiding as far as possi

3、ble prescriptive requirements and allthe traditional designations of these products available throughoutEurope.EN 845-1 includes clauses covering initial type tests, factoryproduction control, sampling for initial type testing andindependent testing of consignments. These are similar in allmasonry p

4、roduct specifications.The UK National Annex NA attached to this standard providesan informative commentary on the use of BS EN 845-1 in theUK. Nothing in this annex should be construed as specifyingrequirements other than those contained in the normative parts ofthis European Standard.If CE marking

5、is performed, the procedures in Annex ZA will apply.The significance of the CE marking is that the product manufacturerclaims compliance with the “harmonized” requirements given in thenormative text of the product standard. These relate to the essentialrequirements of the EU Construction Products Di

6、rective. Not allproduct characteristics need necessarily be given on the CE marking,but those product characteristics covered by regulations in force ineach EU Member State, where the manufacturer intends that theproduct will be used, do need to be stated.The UK participation in its preparation was

7、entrusted to TechnicalCommittee B/519/3, Ancillary components.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The

8、 British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79415 5ICS 91.060.10; 91.080.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committ

9、ee on 31 July 2013.Amendments issued since publicationDate Text affectedBS EN 845-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 845-1:2013. Itsupersedes BS EN 845-1:2003+A1:2008 which is withdrawn.EN 845-1 specifies the characteristics and performance r

10、equirementsfor ties, joist hangers, straps and brackets available throughout theCEN member countries. It aims to do so in product performanceterms, avoiding as far as possible prescriptive requirements and allthe traditional designations of these products available throughoutEurope.EN 845-1 includes

11、 clauses covering initial type tests, factoryproduction control, sampling for initial type testing andindependent testing of consignments. These are similar in allmasonry product specifications.The UK National Annex NA attached to this standard providesan informative commentary on the use of BS EN 8

12、45-1 in theUK. Nothing in this annex should be construed as specifyingrequirements other than those contained in the normative parts ofthis European Standard.If CE marking is performed, the procedures in Annex ZA will apply.The significance of the CE marking is that the product manufacturerclaims co

13、mpliance with the “harmonized” requirements given in thenormative text of the product standard. These relate to the essentialrequirements of the EU Construction Products Directive. Not allproduct characteristics need necessarily be given on the CE marking,but those product characteristics covered by

14、 regulations in force ineach EU Member State, where the manufacturer intends that theproduct will be used, do need to be stated.The UK participation in its preparation was entrusted to TechnicalCommittee B/519/3, Ancillary components.A list of organizations represented on this committee can beobtain

15、ed on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79415 5ICS 91.060.10; 91.080.30Complia

16、nce with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationDate Text affectedStandards Policy and Strategy Committee on 31 August 201

17、3.Amendments/corrigenda issued since publicationBS EN 845-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 845-1 June 2013 ICS 91.080.30 Supersedes EN 845-1:2003+A1:2008English Version Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brack

18、ets Spcification pour composants accessoires de maonnerie - Partie 1 : Attaches, brides de fixation, triers de support et consoles Festlegungen fr Ergnzungsbauteile fr Mauerwerk - Teil 1: Maueranker, Zugbnder, Auflager und Konsolen This European Standard was approved by CEN on 21 March 2013. CEN mem

19、bers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicat

20、ion to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manage

21、ment Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

22、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 B

23、russels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 845-1:2013: EBS EN 845-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 845-1:2013. It supersedes BS EN 845-1:2003+A1:2008 whi

24、ch will be withdrawn on 31 December 2013.EN 845-1 is the subject of transitional arrangements agreed under the Commission mandate. The Member States have agreed a transition period for the co-existence of EN 845-1 and their corresponding national standard(s). At the end of this co-existence period,

25、that is at the end of December 2013, BS EN 845-1:2003+A1:2008 will be superseded and withdrawn.Date Text affected30 September 2013 Correction to supersession detailsISBN 978 0 580 84264 1echnical Committee B/519, Masonry and associated testing.BS EN 845-1:2013 BRITISH STANDARDNational forewordThis B

26、ritish Standard is the UK implementation of EN 845-1:2013. Itsupersedes BS EN 845-1:2003+A1:2008 which is withdrawn.EN 845-1 specifies the characteristics and performance requirementsfor ties, joist hangers, straps and brackets available throughout theCEN member countries. It aims to do so in produc

27、t performanceterms, avoiding as far as possible prescriptive requirements and allthe traditional designations of these products available throughoutEurope.EN 845-1 includes clauses covering initial type tests, factoryproduction control, sampling for initial type testing andindependent testing of con

28、signments. These are similar in allmasonry product specifications.The UK National Annex NA attached to this standard providesan informative commentary on the use of BS EN 845-1 in theUK. Nothing in this annex should be construed as specifyingrequirements other than those contained in the normative p

29、arts ofthis European Standard.If CE marking is performed, the procedures in Annex ZA will apply.The significance of the CE marking is that the product manufacturerclaims compliance with the “harmonized” requirements given in thenormative text of the product standard. These relate to the essentialreq

30、uirements of the EU Construction Products Directive. Not allproduct characteristics need necessarily be given on the CE marking,but those product characteristics covered by regulations in force ineach EU Member State, where the manufacturer intends that theproduct will be used, do need to be stated.

31、The UK participation in its preparation was entrusted to TechnicalCommittee B/519/3, Ancillary components.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are

32、 responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79415 5ICS 91.060.10; 91.080.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

33、 of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationDate Text affectedBS EN 845-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 845-1:2013. Itsupersedes BS EN 845-1:2003+A1:2008 which is withdrawn.EN 845-1 spe

34、cifies the characteristics and performance requirementsfor ties, joist hangers, straps and brackets available throughout theCEN member countries. It aims to do so in product performanceterms, avoiding as far as possible prescriptive requirements and allthe traditional designations of these products

35、available throughoutEurope.EN 845-1 includes clauses covering initial type tests, factoryproduction control, sampling for initial type testing andindependent testing of consignments. These are similar in allmasonry product specifications.The UK National Annex NA attached to this standard providesan

36、informative commentary on the use of BS EN 845-1 in theUK. Nothing in this annex should be construed as specifyingrequirements other than those contained in the normative parts ofthis European Standard.If CE marking is performed, the procedures in Annex ZA will apply.The significance of the CE marki

37、ng is that the product manufacturerclaims compliance with the “harmonized” requirements given in thenormative text of the product standard. These relate to the essentialrequirements of the EU Construction Products Directive. Not allproduct characteristics need necessarily be given on the CE marking,

38、but those product characteristics covered by regulations in force ineach EU Member State, where the manufacturer intends that theproduct will be used, do need to be stated.The UK participation in its preparation was entrusted to TechnicalCommittee B/519/3, Ancillary components.A list of organization

39、s represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978

40、0 580 79415 5ICS 91.060.10; 91.080.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationDate Text affectedStandards Po

41、licy and Strategy Committee on 31 August 2013.Amendments/corrigenda issued since publicationBS EN 845-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 845-1 June 2013 ICS 91.080.30 Supersedes EN 845-1:2003+A1:2008English Version Specification for ancillary components for masonry - Part 1:

42、Wall ties, tension straps, hangers and brackets Spcification pour composants accessoires de maonnerie - Partie 1 : Attaches, brides de fixation, triers de support et consoles Festlegungen fr Ergnzungsbauteile fr Mauerwerk - Teil 1: Maueranker, Zugbnder, Auflager und Konsolen This European Standard w

43、as approved by CEN on 21 March 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na

44、tional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own lan

45、guage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greec

46、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG M

47、anagement Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 845-1:2013: EBS EN 845-1:2013EN 845-1:2013 (E)2Contents PageForeword. 4 1 Scope 5 2 Normative references . 5 3 Terms, definiti

48、ons and symbols 7 3.1 Terms and definitions. 7 3.2 Symbols . 10 4 Materials. 23 4.1 General. 23 4.2 Fixings and materials not supplied by the manufacturer . 23 5 Requirements 24 5.1 General. 24 5.2 Dimensions and limit deviations . 24 5.2.1 Method of measurement and accuracy 24 5.2.2 Length, applica

49、ble cavity width, embedment and fixings (number, size and location) . 24 5.2.3 Thickness or diameter 25 5.2.4 Other information 25 5.3 Mechanical strength . 25 5.3.1 Wall ties and associated fixings 25 5.3.2 Joist hangers. 28 5.3.3 Brackets . 28 5.3.4 Tension straps. 29 5.4 Resistance to water crossing a cavity 30 5.5 Safety during installation . 30 5.6 Durability 30 5.7 Dangerous substances. 30 6 Description and designation 31 7 Marking 33 8 Evaluation of conformity 33 8.1 General. 33 8.2 Initial type tests . 33 8.3 Factory production control 34 8.3.1 General