EN 506-2008 en Roofing products of metal sheet - Specification for selfsupporting products of copper or zinc sheet《金属薄板材制屋顶材料产品 铜或锌薄板材制直支撑式产品规范》.pdf

《EN 506-2008 en Roofing products of metal sheet - Specification for selfsupporting products of copper or zinc sheet《金属薄板材制屋顶材料产品 铜或锌薄板材制直支撑式产品规范》.pdf》由会员分享，可在线阅读，更多相关《EN 506-2008 en Roofing products of metal sheet - Specification for selfsupporting products of copper or zinc sheet《金属薄板材制屋顶材料产品 铜或锌薄板材制直支撑式产品规范》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 506:2008ICS 91.060.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRoofing productsof metal sheet Specification for self-supporting products ofcopper or zinc sheetThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCo

2、mmittee on 31 March2009 BSI 2009ISBN 978 0 580 59448 9Amendments/corrigenda issued since publicationDate CommentsBS EN 506:2008National forewordThis British Standard is the UK implementation of . It supersedes BSEN 506:2000 which is withdrawn.The UK participation in its preparation was entrusted to

3、TechnicalCommittee B/542/5, Sheet roof and wall coverings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Complia

4、nce with a British Standard cannot confer immunityfrom legal obligations.BS EN 506:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 506July 2008ICS 91.060.20 Supersedes EN 506:2000 English VersionRoofing products of metal sheet - Specification for self-supporting products of copper or zinc shee

5、tProduits de couverture en tle mtallique - Spcificationpour les plaques de couverture en tle de cuivre ou de zincDacheindeckungsprodukte aus Metallblech - Festlegungenfr selbsttragende Bedachungselemente aus Kupfer- oderZinkblechThis European Standard was approved by CEN on 30 May 2008.CEN members a

6、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to t

7、he CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same s

8、tatus as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania,

9、 Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwi

10、de for CEN national Members.Ref. No. EN 506:2008: EBS EN 506:2008EN 506:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions, symbols and abbreviations.6 3.1 General6 3.2 Materials .6 3.3 Profile definitions.7 3.4 Product geometry 10 3.5 Symbo

11、ls and abbreviations 12 4 Requirements.13 4.1 General13 4.2 Materials .13 4.2.1 Copper 13 4.2.2 Organic coatings or chemical treatments on zinc-copper-titanium.13 4.2.3 Material tolerances 13 4.3 Products .14 4.3.1 Mechanical resistance.14 4.3.2 Calculation14 4.3.3 Dimensions.14 4.3.4 Dimensional to

12、lerances for the profiled sheets .14 4.3.5 Safety in case of fire14 5 Test methods14 5.1 Material properties.14 5.2 Structural properties .14 6 Designation 15 7 Marking, labelling and packaging 15 7.1 Marking and labelling 15 7.2 Packaging and special ordering conditions .15 7.3 Transport, storage a

13、nd handling15 Annex A (normative) Dimensional tolerances .17 A.1 Tolerances for trapezoidal sheets17 A.1.1 General17 A.1.2 Depth of profile 17 A.1.3 Depth of stiffeners .18 A.1.4 Pitch 18 A.1.5 Widths of crown and valley 19 A.1.6 Cover width 19 A.1.7 Radius of bends.20 A.1.8 Deviation from straightn

14、ess .21 A.1.9 Deviation from squareness.22 A.1.10 Length .22 A.1.11 Deviation of side lap23 A.1.12 Curve radius and angles .23 A.2 Tolerances for sinusoidal profiles .24 A.3 Tolerances on tiles 24 A.3.1 General24 BS EN 506:2008EN 506:2008 (E) 3 A.3.2 Depth of tile25 A.3.3 Web angular displacement (F

15、igure A.12)26 A.3.4 Pitch26 A.3.5 Width of crown and valley (Figure A.14).26 A.3.6 Cover width 27 A.3.7 Radius of bends.27 A.3.8 Deviation from straightness.28 A.3.9 Deviation from squareness 28 A.3.10 Length.29 A.3.11 Contraction or bulging29 A.4 Methods for measuring profiles.30 A.4.1 General .30

16、A.4.2 Depth of profile 30 A.4.3 Depth of stiffeners.30 A.4.4 Pitch30 A.4.5 Width of crown and valley 31 A.4.6 Cover width 32 A.4.7 Radius of bends.32 A.4.8 Straightness.32 A.4.9 Squareness 32 A.4.10 Length.32 A.4.11 Side laps.32 A.4.12 Side lap ripple 32 Annex B (informative) Test methods for concen

17、trated load 34 Bibliography35 BS EN 506:2008EN 506:2008 (E) 4 Foreword This document (EN 506:2008) has been prepared by Technical Committee CEN/TC 128 “Roof covering for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be giv

18、en the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may

19、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 506:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impl

20、ement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

21、 and the United Kingdom. BS EN 506:2008EN 506:2008 (E) 5 Introduction Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing products of metal. Roofing products of metal Self-supporting products Fully supported products EN 14782 Copper / Zinc EN 506 Ste

22、el EN 508-1 Aluminium EN 508-2 Stainless steel EN 508-3 Figure 1 Framework of standards In this standard the performance of the product has been defined in terms of calculation and a number of type tests. The performance of a roof constructed with these products depends not only on the properties of

23、 the product as required by this standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use. BS EN 506:2008EN 506:2008 (E) 6 1 Scope This European Standard specifies requirements for self-supporting roofing products for

24、discontinuous laying made from copper or zinc-copper-titanium alloy sheet with or without additional organic coatings. The standard establishes general characteristics, definitions and labelling for the products, together with requirements for the materials from which the products can be manufacture

25、d. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service con

26、ditions. The standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transf

27、er any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of roof system and execution of connections and flashings are included. 2 Normative references The following referenced documents are indispensable for the application of thi

28、s document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 988, Zinc and zinc alloys - Specifications for rolled flat products for building EN 1172, Copper and copper alloys - Sheet an

29、d strip for building purposes 3 Terms and definitions, symbols and abbreviations For the purposes of this document, the following terms and definitions apply. 3.1 General 3.1.1 self-supporting product product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, w

30、ind, foot traffic) and transmit these loadings to discretely spaced structural supports. 3.2 Materials 3.2.1 copper cold rolled copper sheets of grade Cu-DHP, phosphorus-deoxidized copper - high residual phosphorus NOTE 1 The chemical composition is given in EN 1172. NOTE 2 The system used for desig

31、nating the materials specified in this standard is based on ISO 431 and ISO 1190-1. 3.2.2 zinc-copper-titanium alloy made from zinc grade Z1 conforming to EN 1179, that is 99,995 % minimum zinc content, with addition of alloying elements and the composition of which is as specified in EN 988 BS EN 5

32、06:2008EN 506:2008 (E) 7 3.2.3 organic coated zinc-copper-titanium painted, laminated or coil coated (continuously organic coated) zinc-copper-titanium sheet 3.3 Profile definitions 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, the cr

33、owns of which may be rounded and, in addition, the crowns, web and valley may be stiffened NOTE See Figures 2 to 5. Figure 2 Part of typical trapezoidal profile Figure 3 Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trapezoidal profile with stiffened crown and web

34、Figure 5 Part of typical trapezoidal profile with stiffened valley BS EN 506:2008EN 506:2008 (E) 8 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected with tangential webs N

35、OTE See Figure 6. Figure 6 Part of typical sinusoidal profiled sheet 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the weather NOTE 1 See Figures 7 and 8. NOTE 2 The profile shape is

36、 designed to allow the formation of side laps on site. NOTE 3 As these types of roof covering products are used in proprietary roofing systems, no structural requirements are given within this standard. NOTE 4 These products are normally designed by testing. Figure 7 Typical standing seam profile Fi

37、gure 8 Typical concealed fix profile BS EN 506:2008EN 506:2008 (E) 9 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to be side and/or end lapped NOTE 1 See figures 9a, 9b and 9c. NOTE 2 The tile profiles may include transverse steps. NOTE 3 As these types of roof

38、covering products are used in proprietary systems no structural requirements are given within this standard. NOTE 4 These products are normally designed by testing. Figure 9 Typical tile profiles BS EN 506:2008EN 506:2008 (E) 10 3.4 Product geometry NOTE The names for various parts of typical trapez

39、oidal profiles sheets are given in Figures 10 a) and 10 b), with additional definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12. Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Trough 11 Drainage groove 6 Web 12 Crown stiffen

40、er a) Definitions of the parts of typical trapezoidal profiled sheets BS EN 506:2008EN 506:2008 (E) 11 Key 1 Bend radius 2 End lap 3 Web angle 4 Overlap 5 Underlap 6 Side lap in principle the same on tiles b) Definitions of the parts of typical trapezoidal profiled sheets Figure 10: Definitions of t

41、he parts of typical profiled sheets BS EN 506:2008EN 506:2008 (E) 12 Key 1 Depth 2 Pitch Figure 10 Definitions of the parts of typical sinusoidal profiled sheets Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap Figure 11 Definitions of the parts of typical tile 3.5 Symbols a

42、nd abbreviations Cu-DHP see 3.2.1. Zn-Cu-Ti Zinc-copper-titanium (see EN 988) For Zn-Cu-Ti-alloy with additional organic coatings or chemical treatment: AY indicating acrylic paint coating SP indicating polyester paint coating SP-SI indicating silicone-modified polyester paint coating PVDF indicatin

43、g polyvinylidenefluoride paint coating BS EN 506:2008EN 506:2008 (E) 13 PVC(P) indicating polyvinylchloride (plastisol) coating, applied by coil coating process PW preweathered surface by chemical treatment 4 Requirements 4.1 General The product shall be manufactured from materials complying with 4.

44、2. NOTE The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. A permanent quality system shall be

45、 adopted by the manufacturer1. 4.2 Materials 4.2.1 Copper The copper used shall be of grade Cu-DHP in accordance with EN 1172. 4.2.2 Organic coatings or chemical treatments on zinc-copper-titanium Organic coating or chemical treatment shall be selected depending on processing and service conditions.

46、 For the purposes of this standard, the coating systems shall be as given in Table 1. NOTE The coatings referred to in this standard are mainly used for decorative purposes. Table 1 Factory applied organic coatings or chemical treatment Type of coating Designation Factory applied coatings Acrylic Po

47、lyester Silicone-modified polyester Polyvinylidene fluoride Polyvinyl chloride (Plastisol) AY SP SP-SI PVDF PVC(P) Chemical treatment Preweathered surface PW The reverse side coating should be chosen as appropriate. This is required for handling, storage and for corrosion protection in some conditio

48、ns. 4.2.3 Material tolerances The tolerances on material thicknesses shall be in accordance with EN 1172 for copper products and EN 988 for zinc-copper-titanium products. 1E.g. quality management system based on EN ISO 9001. BS EN 506:2008EN 506:2008 (E) 14 4.3 Products 4.3.1 Mechanical resistance T

49、he product shall resist the design loads from snow, wind and maintenance. These loads shall be factored such that they will not impair the performance of the roof in any respect. NOTE The load level, the levels of safety and permissible deflection are defined in national building regulations. 4.3.2 Calculation The mechanical performance of the product shall be stated by the manufacturer, together with details of how the values were determined in accordance with the national regulations of the country in which the products is to be used. NOTE 1 No