EN 505-2013 en Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet《金属薄板屋顶制品 全支撑薄钢板屋顶制品规格》.pdf

《EN 505-2013 en Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet《金属薄板屋顶制品 全支撑薄钢板屋顶制品规格》.pdf》由会员分享，可在线阅读，更多相关《EN 505-2013 en Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet《金属薄板屋顶制品 全支撑薄钢板屋顶制品规格》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 505:2013Roofing products from metal sheet Specification for fully supported roofing products of steel sheetBS EN 505:2013 BRITISH STANDARDNational forewordThis British Stan

2、dard is the UK implementation of EN 505:2013. It supersedes BS EN 505:2000, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e B / 5 4 2 / 6 , C o r r u g a t e d s h e e t i n g m a t e r i a l s .A list of organizations represented on th

3、is committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013.ISBN 978 0 580 79138 3

4、ICS 77.140.50; 91.060.20 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2013.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 505:20

5、13EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 505 March 2013 ICS 77.140.50; 91.060.20 Supersedes EN 505:1999English Version Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet Produits de couverture en tle mtallique - Spcification pour les p

6、roduits de couverture en feuille dacier totalement supports Dachdeckungsprodukte aus Metallblech - Spezifikation fr vollflchig untersttzte Dachdeckungsprodukte aus Stahlblech This European Standard was approved by CEN on 5 February 2013. CEN members are bound to comply with the CEN/CENELEC Internal

7、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

8、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official version

9、s. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

10、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form

11、 and by any means reserved worldwide for CEN national Members. Ref. No. EN 505:2013: EBS EN 505:2013EN 505:2013 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions, symbols, units and abbreviated terms . 5 3.1 Terms and definitions . 5 3.2 Symbol

12、s and abbreviated terms 7 4 Requirements 7 4.1 General 7 4.2 Materials 8 4.3 Products 9 5 Sampling and test methods 11 5.1 Flat products . 11 5.2 Formed (prefabricated) products . 12 6 Designation . 12 7 Marking, labelling and packaging 12 7.1 Marking and labelling . 12 7.2 Packaging and any special

13、 ordering conditions . 13 7.3 Transport, storage and handling 13 Annex A (informative) Aluminium coated steel sheet (type A) 14 A.1 General 14 A.2 Roof covering products 14 Annex B (normative) Multilayer coated steel sheet . 16 B.1 General 16 B.2 Substrate materials . 16 B.3 Specific requirements .

14、16 B.4 Freedom from defects 17 Annex C (informative) Metallic coatings 18 Annex D (informative) A-deviations 20 Bibliography 21 BS EN 505:2013EN 505:2013 (E) 3 Foreword This document (EN 505:2013) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying an

15、d products for wall cladding“, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the

16、 latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 505:1999. In comparison to the

17、previous edition, the following sections were changed or added: Clause 2, Clause 3, 4.3.1, Annex B, B.3.2, Table C.1, Table C.2 and Annex D. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standar

18、d: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain

19、, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 505:2013EN 505:2013 (E) 4 Introduction Figure 1 indicates the position of this European Standard in the CEN framework of standards concerning roofing product of metal. Roofing products of metal Self supporting products Fully supported produ

20、cts Zinc EN 501 Stainless steel EN 502 Copper EN 504 Steel EN 505 Aluminium EN 507 References regarding Materials Quality assurance Figure 1 Framework of standards In this European Standard, the performance of the product has been defined in terms of a number of type tests. The performance of a roof

21、 constructed with these products depends not only on the properties of the product as it is required by this European Standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use. Metallic coated steel sheet can be easily

22、fabricated. It can be sheared, punched, pressed, drawn, folded, roll-formed without difficulty within the given limits of the properties listed in the respective material specifications. Coil coated sheet can be fabricated like metallic coated steel sheet in most applications, but minimum bend radii

23、, design of forming tools, process temperature etc are chosen according to material properties. BS EN 505:2013EN 505:2013 (E) 5 1 Scope This European Standard specifies requirements for roofing products used for assembly into coverings for pitched roofs, made from metallic coated steel sheet with or

24、 without additional organic coatings. The European Standard establishes general characteristics, definitions and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that thei

25、r products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semiformed products as well as

26、 strip, coil and sheet for on-site-formed applications (e.g. standing-seam and clip fixroofs). The European Standard applies to all discontinuously laid and fully supported roofing products made of steel sheets. No requirements for supporting construction, design of roof system and execution of conn

27、ections and flashings are included. NOTE The European Standard deals partly with flat products, partly with formed (prefabricated) products. Requirements for preformed self-supporting products are given in EN 508-1. 2 Normative references The following documents, in whole or in part, are normatively

28、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 508-1, Roofing products from metal sheet Specification for self-s

29、upporting products of steel, aluminium or stainless steel sheet Part 1: Steel EN 1427, Bitumen and bituminous binders Determination of the softening point Ring and Ball method EN 10079:2007, Definition of steel products EN 10143, Continuously hot-dip metal coated steel sheet and strip Tolerances on

30、dimensions and shape EN 10169, Continuously organic coated (coil coated) steel flat products Technical delivery conditions EN 10204, Metallic products Types of inspection documents EN 10346, Continuously hot-dip coated steel flat products Technical delivery conditions EN ISO 6270-1, Paints and varni

31、shes Determination of resistance to humidity Part 1: Continuous condensation (ISO 6270-1) EN ISO 6988, Metallic and other non-organic coatings Sulfur dioxide test with general condensation of moisture (ISO 6988) EN ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests (ISO 9227) 3 Ter

32、ms, definitions, symbols, units and abbreviated terms 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079:2007 and the following apply. BS EN 505:2013EN 505:2013 (E) 6 3.1.1 hot-dip zinc coated steel sheet (type Z) product obtained by continuously

33、 hot-dip zinc coating cold reduced strips of either low carbon steel for cold forming to EN 10346 or steel of structural quality to EN 10346 3.1.2 hot-dip zinc-aluminium coated steel sheet (type ZA) product obtained by continuously hot-dip coating cold reduced strips of low carbon steel for cold for

34、ming steel or steel of structural quality on a production line using an alloy consisting of: 5 % aluminium (mass fraction); 95 % zinc (mass fraction); small amounts of mischmetal Note 1 to entry: EN 10346 refers to this type of steel. 3.1.3 hot-dip aluminium-zinc coated steel sheet (type AZ) product

35、 obtained by continuously hot-dip coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a production line using an alloy consisting of: 55 % aluminium (mass fraction); 1,5 % silicon (mass fraction); balance zinc Note 1 to entry: EN 10346 refers to this ty

36、pe of steel. 3.1.4 hot-dip aluminium-coated steel sheet (type A) product obtained by continuously hot-dip aluminium coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a continuous production line Note 1 to entry: See Annex A. 3.1.5 organic coated steel

37、 sheet product obtained by factory application of paint by roller or spray processes, or factory applied organic film, on substrates of type Z, type ZA, type AZ or type A coated steel sheet Note 1 to entry: EN 10169 refers to this type of coated steel. 3.1.6 multilayer coated steel sheet product obt

38、ained by continuously coating on both sides hot-dip zinc coated cold reduced strips of low carbon steel for cold forming or steel of structural qualities with one or multiple applications of thermoplastic asphalt compounds and subsequent lamination of a metal foil with or without decorative painting

39、 Note 1 to entry: See Annex B. Note 2 to entry: Minimum thickness of coating 1,5 mm. 3.1.7 fully supported installation conditions such that the bottom flat portions of the product are supported by a continuous construction BS EN 505:2013EN 505:2013 (E) 7 3.2 Symbols and abbreviated terms Z Hot-dip

40、zinc coated steel ZA Hot-dip zinc/aluminium coated steel AZ Hot-dip aluminium/zinc coated steel A Hot-dip aluminium coated steel ML Multilayer coated steel AY Acrylic paint coating SP Polyester paint coating SP-SI Silicone-modified polyester paint coating PVDF Polyvinylidenefluoride paint coating PV

41、F(F) Polyvinylfluoride-film coating PVC(P) Polyvinylchloride (plastisol)-coating, applied by coil coating process. PUR Polyurethane paint coating SP-PA Polyamid-modified polyester paint coating EXAMPLES Z275 PVDF PVDF paint coating, applied to steel sheet with hot-dip zinc coating. Nominal zinc coat

42、ing mass 275 g/m2total both sides. Z275 Hot-dip zinc coating, nominal coating mass 275 g/m2total both sides. ZA255 Hot-dip 5 % Al-Zn alloy-coating, nominal coating mass 255 g/m2total both sides. AZ185 Hot-dip 55 % Al-Zn alloy-coating, nominal coating mass 185 g/m2total both sides. 4 Requirements 4.1

43、 General The product shall be manufactured from materials complying with 4.2. The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (

44、according to EN 10204) on request. NOTE The symbols and abbreviations that are used to designate the steel grade, the type and mass of the metallic coating are those of the standards referred to in Clause 2. A permanent quality control system shall be adopted by the manufacturer.1)1) For example, a

45、Quality Management System based on EN ISO 9000. BS EN 505:2013EN 505:2013 (E) 8 4.2 Materials 4.2.1 Steel All steel grades in EN 10346 are suitable for fabrication of fully supported roofing products, either in an industrial process or by an on-site-process. Depending on processing conditions and/or

46、 requested mechanical properties, higher steel grades may be chosen according to the grade values given in the respective material standards. 4.2.2 Nominal metallic coating The minimum nominal metallic coating mass depends on geographic and climatic conditions and shall be chosen from Table 1. The m

47、etallic coating mass shall be the sum of the coating masses on both sides in grams per square metre measured and with tolerances as specified in the appropriate standard. NOTE The minimum nominal metallic coating masses specified in some countries in their regulations or codes of practice are listed

48、 in Annex C. Table 1 Nominal metallic coating masses Hot-dip coating type Coating designation with organic coating without organic coating Zinc type Z Z200 Z225 Z275 Z275 Z350 Z450 5 % Al-Zn type ZA ZA200 ZA255 ZA255 ZA300 55 % Al-Zn type AZ AZ150 AZ150 AZ185 Aluminium-coating type A A195 A230 4.2.3

49、 Organic coatings The main weather resistant organic coatings suitable for application to metallic coated steel substrates are given in Table 2. Table 2 Factory applied organic coatings Type of coating Designation Factory applied coatings Acrylic Polyester Silicone-modified polyester Polyvinylidene fluoride Polyvinyl chloride (Plastisol) Polyurethane Polyamide-modified polyester Multicoat polyvinylidenefluoride Multicoat polyurethane AY SP SP-SI PVDF PVC (P) PUR SP-PA - - Factory applied laminated film Polyvinylfluoride PVF (F) B