EN 485-1-2016 en Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery《铝及铝合金板-带材和板材-第1部分 检验和交货技术条件》.pdf

《EN 485-1-2016 en Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery《铝及铝合金板-带材和板材-第1部分 检验和交货技术条件》.pdf》由会员分享，可在线阅读，更多相关《EN 485-1-2016 en Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery《铝及铝合金板-带材和板材-第1部分 检验和交货技术条件》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 485-1:2016Aluminium and aluminiumalloys Sheet, strip and platePart 1: Technical conditions for inspectionand deliveryBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 485-1:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation

2、 of EN 485-1:2016. Itsupersedes BS EN 485-1:2008+A1:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can beobtained on request to its secretary.This publicat

3、ion does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 91766 0ICS 77.150.10Compliance with a British Standard cannot confer immunity from

4、legal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2016.Amendments issued since publicationDate Text affectedBS EN 485-1:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 485-1 July 2016 ICS 77.150.10 Supersedes

5、 EN 485-1:2008+A1:2009English Version Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery Aluminium et alliages daluminium - Tles, bandes et tles paisses - Partie 1: Conditions techniques de contrle et de livraison Aluminium und Aluminiu

6、mlegierungen - Bnder, Bleche und Platten - Teil 1: Technische Lieferbedingungen This European Standard was approved by CEN on 12 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a natio

7、nal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A vers

8、ion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, C

9、zech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

10、 EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 485-1:2016

11、EBS EN 485-1:2016EN 485-1:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 6 4 Ordering information 6 5 Requirements . 8 6 Test methods 9 7 Inspection document 16 8 Marking of products 16 9 Packaging 16 10 Complaints of non conformity . 16 A

12、nnex A (normative) European Standards for strip, sheet and plate of special form and for special applications . 17 Bibliography . 18 BS EN 485-1:2016EN 485-1:2016 (E) 3 European foreword This document (EN 485-1:2016) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys

13、”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017. Att

14、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 485-1:2008+A1:2009. EN 485 comprises the following parts under the general t

15、itle “Aluminium and aluminium alloys Sheet, strip and plate”: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions and form for hot-rolled products Part 4: Tolerances on shape and dimensions for cold-rolled products CEN/TC 132 affirm

16、s it is policy that in the case when a patentee refuses to grant licences on standardized standard products under reasonable and not discriminatory condition, then this product should be removed from the corresponding document. According to the CEN-CENELEC Internal Regulations, the national standard

17、s organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

18、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 485-1:2016EN 485-1:2016 (E) 4 1 Scope This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought alumi

19、nium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing. It applies to products with a thickness over 0,20 mm up to and including 400 mm. For many special applications of aluminium strip, sheet and plate, specific European Standards exist, whe

20、re different or additional requirements are formulated and the appropriate alloys and tempers are selected: see Annex A. Most of these special European Standards refer to provisions of this document. The selection of the relevant special European Standards is under the responsibility of the purchase

21、r. Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue strength, surface appearance and welding properties, the user should consult the supplier and consider the relevant special European Standard, as applicable. 2 Normative references The following

22、 documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-2, Aluminium

23、and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances o

24、n shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations EN 541, Aluminium and aluminium alloys - Rolled products for cans, closures and lids - Specifications EN 573-3, Aluminium and aluminium alloys - Chemical composition and fo

25、rm of wrought products - Part 3: Chemical composition and form of products EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff EN 603 (all parts), Aluminium and aluminium all

26、oys Wrought forging stock EN 683-1, Aluminium and aluminium alloys - Finstock - Part 1: Technical conditions for inspection and delivery EN 851, Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications EN 941, Aluminium and aluminium alloys -

27、Circle and circle stock for the production of general applications - Specifications EN 1386, Aluminium and aluminium alloys - Tread plate - Specifications EN 1396, Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications BS EN 485-1:2016EN 485-1:2016 (E)

28、 5 EN 1669, Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip EN 2004-1, Aerospace series - Test methods for aluminium and aluminium alloy products - Part 1: Determination of electrical conductivity of wrought aluminium alloys EN 10204, Metallic products - Types of insp

29、ection documents EN 12258-1, Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms EN 12392, Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment EN 12482-1, Aluminium and al

30、uminium alloys - Reroll stock for general applications - Part 1: Specifications for hot rolled reroll stock EN 12482-2, Aluminium and aluminium alloys - Reroll stock for general applications - Part 2: Specifications for cold rolled reroll stock EN 13195, Aluminium and aluminium alloys - Specificatio

31、ns for wrought and cast products for marine applications (shipbuilding, marine and offshore) EN 13981-2, Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 2: Plates and sheets EN 14121, Aluminium and aluminium allo

32、ys - Sheet, strip and plate for electrotechnical applications EN 14242, Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectral analysis EN 14286, Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation

33、of dangerous goods EN 14287, Aluminium and aluminium alloys - Specific requirements on the chemical composition of products intended to be used for the manufacture of packaging and packaging components EN 14361, Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts EN 14392,

34、 Aluminium and aluminium alloys - Requirements for anodised products for use in contact with foodstuff EN 15088, Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery EN ISO 6892-1, Metallic materials - Tensile testing - Part 1

35、: Method of test at room temperature (ISO 6892-1) EN ISO 7438, Metallic materials - Bend test (ISO 7438) EN ISO 20482, Metallic materials - Sheet and strip - Erichsen cupping test (ISO 20482) ISO 9591, Corrosion of aluminium alloys Determination of resistance to stress corrosion cracking ASTM G34, S

36、tandard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) BS EN 485-1:2016EN 485-1:2016 (E) 6 ASTM G47, Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products ASTM G66, Standard

37、Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test) ASTM G67, Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test) 3

38、Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1 and the following apply. 3.1 sheet/plate flat rolled product of rectangular cross-section with uniform thickness between 0,20 mm and 6 mm for sheet or above 6 mm for plate, supplied in straight len

39、gths (i.e. flat) usually with trimmed or sawn edges Note 1 to entry: For sheet, the thickness does not exceed one-tenth of the width. Note 2 to entry: Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges), coated, edge conditioned and perforated products

40、 in this general form when derived from sheet as defined above are classified as sheet. Note 3 to entry: Flat sheets and plates material between 3 mm and 15 mm are sometimes called “shate”. 3.2 strip flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in co

41、ils usually with trimmed edges Note 1 to entry: The thickness does not exceed one-tenth of the width. Note 2 to entry: Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges), coated, edge conditioned and perforated products in this general form when deriv

42、ed from sheet as defined above are classified as sheet. Note 3 to entry: “Strip” is sometimes called “coil”. 3.3 order document document or set of documents agreed between supplier and purchaser at the time of ordering Note 1 to entry: An order document can be an order of the purchaser confirmed by

43、the supplier or a quotation of the supplier confirmed by the purchaser. 4 Ordering information The order document shall contain the following: a) form and type of product: form of the product (sheet, strip, plate, etc.); BS EN 485-1:2016EN 485-1:2016 (E) 7 designation of the aluminium or aluminium a

44、lloy; b) temper of the material for delivery according to EN 515 and, if different, the temper for use; c) reference to this European Standard; d) specification of mechanical properties, if additional to or different from EN 485-2 or as disclosed in any application standard (see Annex A); e) referen

45、ce to the standard for tolerances of form and dimensions (e.g. EN 485-3, EN 485-4 or as disclosed in any application standard (see Annex A); f) dimensions of the product: thickness; width; length of sheet and plate, as applicable (in the rolling direction); internal and external diameters of the coi

46、l, or dimension and type of the core, as applicable. NOTE 1 Unless otherwise agreed, the length is the largest dimension of the sheet or plate and corresponds to the rolling direction. g) quantity: mass or number of pieces; quantity tolerances if required; h) any requirements for inspection document

47、s; i) any other test, in addition to chemical analysis and tensile testing; j) any additional requirements, such as: quality assurance; specific inspection schemes; marking of products; references of drawing, etc.; special packing requirements; k) for products intended for decorative anodizing by th

48、e purchaser, the order document shall also contain the following: statement that the product is intended to be anodized; intended particular surface treatment (according to the relevant standard); BS EN 485-1:2016EN 485-1:2016 (E) 8 whether a decorative appearance after anodizing is required for bot

49、h sides and, if only one side, its position with respect to the strip (inside or outside of the coil) or the sheet or plate (upside or downside). Products intended to form a specific area after anodizing (such as a faade) should be ordered in a single batch. The order document should indicate the intended application. NOTE 2 The codification scheme specified in EN 5735 will preferably be used. 5 Requirements 5.1 Responsibilities of the supplier and manufacturer The supplier shall be responsible that all inspections and tests r