EN 485-1-2008 6875 Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery (Incorporates Amendment A1 2009)《铝和铝合金 薄板材 带材和厚板.pdf

《EN 485-1-2008 6875 Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery (Incorporates Amendment A1 2009)《铝和铝合金 薄板材 带材和厚板.pdf》由会员分享，可在线阅读，更多相关《EN 485-1-2008 6875 Aluminium and aluminium alloys - Sheet strip and plate - Part 1 Technical conditions for inspection and delivery (Incorporates Amendment A1 2009)《铝和铝合金 薄板材 带材和厚板.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 485-1:2008Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspection and deliveryICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g5

2、5g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58A1:2009+Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of

3、EN 485-1:2008+A1:2009. It supersedes BS EN 485-1:2008 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indic

4、ated by !“.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions o

5、f a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 485-1:2008+A1:2009This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2009Ame

6、ndments/corrigenda issued since publicationDate Comments 31 December 2009 Implementation of CEN amendment A1:2009ISBN 978 0 580 66405 2Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS

7、-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 485-1:2008+A1 October 2009 ICS 77.150.10 Supersedes EN 485-1:2008English Version Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery Aluminium et alliages daluminium - Tles, bande

8、s et tles paisses - Partie 1: Conditions techniques de contrle et de livraison Aluminium und Aluminiumlegierungen - Bnder, Bleche und Platten - Teil 1: Technische Lieferbedingungen This European Standard was approved by CEN on 19 January 2008 and includes Amendment 1 approved by CEN on 20 September

9、2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

10、 on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management

11、 Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

12、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and

13、by any means reserved worldwide for CEN national Members. Ref. No. EN 485-1:2008+A1:2009: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 2 Contents Pa

14、ge Foreword 31 Scope 52 Normative references 53 Terms and definitions .64 Ordering information .65 Requirements .86 Test methods 97 Inspection documents 168 Marking of products . 169 Packaging 1710 Complaints of non conformity . 17Annex A (normative) !European Standards for strip, sheet and plate of

15、 special form and for special applications“ 18Bibliography . 19BS EN 485-1:2008+A1:2009Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 3 Foreword This d

16、ocument (EN 485-1:2008+A1:2009) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at t

17、he latest by April 2010, and conflicting national standards shall be withdrawn at the latest by April 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or al

18、l such patent rights. This document includes Amendment 1, approved by CEN on 2009-09-20. This European Standard supersedes !EN 485-1:2008“. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. Within its programme of work, Technical committee CEN/TC 1

19、32 entrusted CEN/TC 132/WG 7 “Sheets, strips and plates“ to revise EN 485-1:1993. EN 485 comprises the following parts under the general title “Aluminium and aluminium alloys Sheet, strip and plate“: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Toler

20、ances on dimensions and form for hot-rolled products Part 4: Tolerances on shape and dimensions for cold-rolled products Besides very slight additional adjustments in the text and update of normative references, the following technical changes have been made: Clause 1: thickness increased to 400 mm;

21、 addition of Clause 6 (previously in EN 485-2); Clause 7 amended; addition of Claude 10; addition of Bibliography. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying an

22、y or all such patent rights. CEN/TC 132 affirms it is policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory condition, then this product shall be removed from the corresponding document. According to the CEN/CENELE

23、C Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, BS EN 485-1:2008+A1:2009Copyright European Committee for Standardization Provided by IHS under license with CENNo

24、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 4 Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

25、 Spain, Sweden, Switzerland and United Kingdom. BS EN 485-1:2008+A1:2009Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 5 1 Scope This document specifie

26、s the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for !general applications“. It also includes !provisions“ for ordering and testing. It applies to products with a thickness over 0,20 mm up to and including 400 mm. !deleted

27、 text“ !For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where different or additional requirements are formulated and the appropriate alloys and tempers are selected: see Annex A. Most of these special European Standards refer to provisions of th

28、is document. The selection of the relevant special European Standards is under the responsibility of the purchaser. Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue strength, surface appearance and welding properties, the user should consult the

29、supplier and consider the relevant special European Standard, as applicable. “ 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the ref

30、erenced document (including any amendments) applies. !EN 485-2:2008“, Aluminium and aluminium alloys Sheet, strip and plate Part 2: Mechanical properties EN 485-3, Aluminium and aluminium alloys Sheet, strip and plate Part 3: Tolerances on dimensions and form for hot-rolled products EN 485-4, Alumin

31、ium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical

32、composition and form of products EN 1669, Aluminium and aluminium alloys Test methods Earing test for sheet and strip EN 2004-1, Aerospace series Test methods for aluminium and aluminium alloy products Part 1: Determination of electrical conductivity of wrought aluminium alloys EN 10002-1, Metallic

33、materials Tensile testing Part 1: Method of test at ambient temperature EN 10204, Metallic products Type of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 14242, Aluminium and aluminium alloys Chemical analysis Inductively coupled

34、plasma optical emission spectral analysis EN 14361, Aluminium and aluminium alloys Chemical analysis Sampling from metal melts EN ISO 7438, Metallic materials Bend test (ISO 7438:2005) BS EN 485-1:2008+A1:2009Copyright European Committee for Standardization Provided by IHS under license with CENNot

35、for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 6 EN ISO 20482, Metallic materials Sheet and strip Erichsen cupping test (ISO 20482:2003) ISO 9591, Corrosion of aluminium alloys Determination of resistance to stress corrosion cracking ASTM G34

36、, Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) ASTM G47, Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products ASTM G66, Standard Test Method for Visual Assessment

37、 of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test) ASTM G67, Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test) 3 Terms and definitions For the pur

38、poses of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 sheet/plate flat rolled product of rectangular cross-section with uniform thickness between 0,20 mm and 6 mm for sheet or above 6 mm for plate, supplied in straight lengths (i.e. flat) usually wit

39、h trimmed or sawn edges NOTE 1 For sheet, the thickness does not exceed one-tenth of the width. NOTE 2 Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges), coated, edge conditioned and perforated products in this general form when derived from sheet as

40、 defined above are classified as sheet. NOTE 3 Flat sheets and plates material between 3 mm and 15 mm are sometimes called “shate“. 3.2 strip flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils usually with trimmed edges NOTE 1 The thickness does n

41、ot exceed one-tenth of the width. NOTE 2 Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges), coated, edge conditioned and perforated products in this general form when derived from sheet as defined above are classified as sheet. NOTE 3 “Strip“ is some

42、times called “coil“. 3.3 order document document or set of documents agreed between supplier and purchaser at the time of ordering NOTE An order document can be an order of the purchaser confirmed by the supplier or a quotation of the supplier confirmed by the purchaser. 4 Ordering information The o

43、rder document shall contain the following: a) form and type of product: BS EN 485-1:2008+A1:2009Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 485-1:2008+A1:2009 (E) 7 form o

44、f the product (sheet, strip, plate, etc.); designation of the aluminium or aluminium alloy; b) temper of the material for delivery according to EN 515 and, if different, the temper for use; c) reference to this European Standard; d) specification of mechanical properties, if additional to or differe

45、nt from !EN 485-2“; e) reference to the standard for tolerances of form and dimensions (EN 485-3 or EN 485-4); f) dimensions and shape of the product: thickness; width; length of sheet and plate, as applicable (in the rolling direction); internal and external diameters of the coil, or dimension and

46、type of the core, as applicable. NOTE 1 Unless otherwise agreed, the length is the largest dimension of the sheet or plate and corresponds to the rolling direction. g) specification or tolerances, if additional to or different from EN 485-3 or EN 485-4; h) quantity: mass or number of pieces; quantit

47、y tolerances if required; i) any requirements for inspection documents; j) any other test, in addition to chemical analysis and tensile testing; k) any additional requirements, such as: quality assurance; specific inspection schemes; marking of products; references of drawing, etc.; special packing

48、requirements; l) for products intended for decorative anodizing by the purchaser, the order document shall also contain the following: statement that the product is intended to be anodized; intended particular surface treatment (according to the relevant European Standard); whether a decorative appearance after anodizing is required for both sides and, if only one side, its position with respect to the strip (inside or outside of the coil) or the sheet or plate (upside or downside). BS EN 485-1:2008+A1:2009Co