EN 479-2018 en Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion.pdf

《EN 479-2018 en Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion.pdf》由会员分享，可在线阅读，更多相关《EN 479-2018 en Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics Poly(vinyl chloride) (PVC) based profiles Determination of heat reversionBS EN 479:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 479 January 2018 ICS 83.080.20; 83.140.99 Supersedes EN 479:1995Englis

2、h Version Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion Plastiques - Profils base de poly(chlorure de vinyle) (PVC) - Dtermination du retrait chaud Kunststoffe - Profile auf Basis von Polyvinylchlorid (PVC) - Bestimmung des Wrmeschrumpfes This European Standa

3、rd was approved by CEN on 6 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s

4、uch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its o

5、wn language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,

6、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE

7、E FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 479:2018 ENational forewordThis British Standard is the UK implementation of EN 479:2018. It sup

8、ersedes BS EN 479:1999, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the n

9、ecessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 94815 2ICS 83.080.20; 83.140.99Compliance with a British Standard cannot confer immunity from legal obligations.This Brit

10、ish Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 479:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 479 January 2018 ICS 83.080.20; 83.140.99

11、Supersedes EN 479:1995English Version Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion Plastiques - Profils base de poly(chlorure de vinyle) (PVC) - Dtermination du retrait chaud Kunststoffe - Profile auf Basis von Polyvinylchlorid (PVC) - Bestimmung des Wrmesch

12、rumpfes This European Standard was approved by CEN on 6 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograph

13、ical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibilit

14、y of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of

15、 Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORM

16、ALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 479:2018 EBS EN 479:2018EN 479:2018 (E) 2 Contents Page European for

17、eword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus . 4 6 Test specimens . 4 7 Conditioning 4 8 Procedure. 5 9 Expression of results 5 10 Test report . 5 BS EN 479:2018EN 479:2018 (E) 3 European foreword This document (EN 479:2018) has been prepared b

18、y Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2018, and conflicting national standards shall be withdra

19、wn at the latest by July 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights. This document supersedes EN 479:1995. According to the CEN/CENELEC Internal

20、Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

21、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 479:2018EN 479:2018 (E) 4 1 Scope This European Standard specifies a method for determining the heat reversion

22、of unplasticized poly(vinyl chloride) (PVC-U) profiles at 100 C in air. It is also applicable to PVC-based profiles at specified temperatures/other test conditions. 2 Normative references There are no normative references in this document. 3 Terms and definitions No terms and definitions are listed

23、in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Principle A test specimen of a specified length of prof

24、ile is maintained in an oven at 100 C for 1 h. A marked length of this test specimen is measured under identical conditions, before and after heating in the oven. The heat reversion is calculated as the percentage change of the final length relative to the initial length per pair of marks. 5 Apparat

25、us 5.1 Air oven, thermostatically controlled, with forced air circulation, in which the test specimens can be exposed to a temperature of 100 C. The oven shall be equipped with a thermostat capable of maintaining the temperature at (100 3) C and a support system which keeps the specimen in position

26、and enables heat transfer. NOTE The use of talc or PTFE foil can be convenient to avoid sticking. 5.2 Measuring device, to measure the length of the test specimen to an accuracy of 0,1 mm. 6 Test specimens 6.1 The test specimen shall be of a minimum length of 250 mm of profile. 6.2 Prepare three sim

27、ilar test specimens per length of profile. 7 Conditioning Condition the test specimens for at least 1 h at room temperature. In cases of dispute the test specimens shall be conditioned at (23 2) C. BS EN 479:2018EN 479:2018 (E) 5 8 Procedure 8.1 Using, a scriber or similar implement, trace on each t

28、est specimen two marks, perpendicular to the profile axis, 200 mm apart, so that one of them is approximately 25 mm from one end of the test specimen. 8.2 Measure for every test specimen at room temperature the distance between the two marks in one pair with an accuracy of 0,1 mm. 8.3 Set the oven t

29、emperature to 100 C. 8.4 When the oven has reached 100 C, place the test specimens horizontally in the oven on the support system. 8.5 Maintain the test specimens in the oven for (6030+) min, after the temperature has regained to 100 C. 8.6 Remove the support system with the test specimens from the

30、oven and let them cool down in air to room temperature on the support system. Under identical conditions to those used in 8.2, measure the distance between the two marks per pair. 8.7 In cases of dispute the cooling of the profiles and the measuring of the distance between the marks shall be perform

31、ed at (23 2) C. 9 Expression of results For each test specimen, calculate the heat reversion R for each pair of marks, as a percentage using the following formula 0100LRL= where L = L0 L1; L0is the distance between the marks before heating in the oven in millimetres; L1is the distance, between the m

32、arks, after heating in the oven in millimetres. Where relevant, calculate for each test specimen the difference of the values of the heat reversion, R, expressed as a percentage, between the two opposing surfaces, as defined in the referring standard. 10 Test report The test report shall include the

33、 following information: a) reference to this document (i.e. EN 479); b) the test laboratory; c) full identification of the profile; BS EN 479:2018EN 479:2018 (E) 6 d) the date of testing; e) the distance between the marks before heating in the oven (L0) for each pair of marks of each test specimen;

34、f) the distance between the marks after heating in the oven (L1) for each pair of marks of each test specimen; g) the value R for each pair of marks for each test specimen; h) the difference of the values of the heat reversion, R, for each test piece, where relevant; i) all operating details not spe

35、cified in this document, as well as any incidents likely to have influenced the results. BS EN 479:2018This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and serv

36、ices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and

37、expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on

38、standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including

39、British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI public

40、ationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial p

41、ublication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior writt

42、en consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole name

43、d user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further re

44、produced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor per

45、mission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have in

46、stant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both

47、 in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Memb

48、er and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current.

49、 For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email