EN 477-1995 en Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Determination of the Resistance to Impact of Main Profiles by Falling Mas.pdf

《EN 477-1995 en Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Determination of the Resistance to Impact of Main Profiles by Falling Mas.pdf》由会员分享，可在线阅读，更多相关《EN 477-1995 en Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Determination of the Resistance to Impact of Main Profiles by Falling Mas.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-BSI BS EN 477-ENGL Lqq? 3b24bb7 0775083 Li27 BRITISH STANDARD Unplas ticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to impact of main profiles by falling mass The European Standard EN 4771995 has the status of a British Stan

2、dard ICs 83.140.99 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS EN 477:1999 _ - _ STD-BSI BS EN Li77-ENGL 1779 Lb24bb7 0775082 3b3 been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standa

3、rds Committee and comes into effect on 15 May 1999 Amd. No. Q BSI O51999 BS EN 477:1999 Date Text affected National foreword This British Standard is the English hguage vemion of EN 477 1%5. The K participation in its preparation was entrusted by kchnical Committee B/538, Doors, windows, shutters, h

4、ardware and curtajn walling, to Subcommittee B/Wl, Windows, which has the responsibihty to: - aid enquirers to understand the tee - present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor

5、reW intemational and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee cm be obtained on request to its secretary. This British Standard forms part of a package of standards on unpbticized polyvinylchloride (PVGU) proles for the fabrication

6、 of windows and doors which will not become fully effective until ail standards in the package have been published and any superseded standards have been withdram. The date of withdrawal for nationai standards will be agreed within CEN and will be notified. Cross-references The British Standards whi

7、ch impiement internationai or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “international Standards Correspondence Index”, or by using the “Find“ facility of the BSI standards Electronic Catalogue. A British Standard does n

8、ot purport to include all the necessary provisions of a conbct. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside fr

9、ont cover, the EN title page, pages 2 to 5 and a back cover. ISBN O 680 32276 9 STD.BSI BS EN Li77-ENGL 1999 Lb2Libb7 0775083 2TT EUROPEAN SrANDARD EN 477 Nom EUROPENNE EuROPISCHl3 NORM May 1995 ICs 83.140; 91.060.50 Descriptors: buildings, windows, non-metallic sections, unplascized polyvinyichiori

10、de, impact tests, shock resistance English version Urplastiw polymqychloride WGU) pmles for the f b) guide mils, fixed to the main frame to accommodate the falling mass and allowing it to fall freely in the vertid plane; c) test piece support, consisting of a rounded off support (see Figure 2) with

11、a distance between (200 i) mm. The support shall be made from steel and rigidly fixed in a solid foundation or on a table with a mass of more than 50 kg; d) relecLse mechanism, such tha the falling mass can fall through a height which can be musted up to (1 500“,0) mm, measured from the top surface

12、of the test piece to be M, e) fihg mass, of (1 O00 f 5) g, which has a hemispherical sr) OC for at least 1 h before testing. Each test piece shal be tested within 10 s of removal hm the conditioning chamber. 7 Procedure 7.1 The test shall be executed on the sight surface of the main profile (prefera

13、bly on the sight surface which is designed to be exposed to the weather). 7.2 Drop the failing mas from the given height as required in the product standard at a point mid-way between two supporting webs. NOTE 1 Where it is impracticable for the mass to hit the profile in accordance with 7.2 due to

14、its geometry, other impact positions for the falling mass should be agreed upon between the profile manufacturer and the testing laborahq. NOTE 2 When due to its geometry, the profile tends to tilt sideways at the impact of the falling mass, any tilting should be prevented, by attaching additionai s

15、tays to the two supports. NOTE 3 During the test care should be taken to prevent multiple impacts of the faiiing mass on the test piece. 8 Expression of results The number of test pieces tested and the number of test pieces broken shall be reported for each type of main profile. 9 Tbst report The te

16、st report shall include the following information: a) reference to this European Standard b) the testing laboratom c) fuli identification of the profile; d) date of testing; e) the height of the fahg mass; f) the number of test pieces tested; g) the number of test pieces broken; h) all operaljng det

17、ails not specified in this European Standard, as weil as incidents likely to have influenced the results. O BSI 061999 STD.BSI BS EN q77-ENGL 1779 = Lb24bb7 07750b TO9 Page 4 EN 477:1996 KEY 1 Faingmass Figure 1 - Example of impact resistance testing apparatus O BSI 06-1999 STD-BSI BS EN Li77-ENGL 1

18、777 I 1b2Libb7 0775087 945 Page 6 EN 477:1995 ! I I i I r i 20 I I 1 i .- I i Dimensions in millimetres Figure 2 - Example of a supporting device o BSI 05-1999 BS EN 4771999 BSI 389 Chiswick High Road London w4 4AL STD-BSI BS EN 477-ENGL 1777 1b24bb7 0775088 881 BSI - British Standards Institution B

19、SI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should mak

20、e sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while wing this British Standard would inform the Secretary of the technical committee resp

21、onsible, the identity of which can be found on the inside front cover. Tel 0181 996 9000. Fax: 0181 996 7400. BSI offers members an individuai updating service ded PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, intemat

22、ional and foreign standards publications should be addressed to Customer Services. Tel O181 996 9001. Fax: O181 996 7001. In response to orders for international sandards, it is BSI policy to supply the BSI implementation of those that have been published as British Stanhds, unless otherwise request

23、ed Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technid Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Co

24、ntact the Information Centre. Tel O181 996 7111. Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Admion. Tel 0181 996 7002.

25、Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardizaon bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extsact may be reproduced, stored in a retrieval

26、system or tsansmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. l%is does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designation

27、s. if these jetails are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if permission is granted, the terms may include royalty payments or a licensing greement. Detais and advice can be obtained from the Copyright Manager. Fel: 0181 996 7070.