EN 3645-010-2006 en Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 or 200 continuous - Part 010 Receptacle h.pdf

《EN 3645-010-2006 en Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 or 200 continuous - Part 010 Receptacle h.pdf》由会员分享，可在线阅读，更多相关《EN 3645-010-2006 en Aerospace series - Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 or 200 continuous - Part 010 Receptacle h.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3645-010:2006Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 010: Receptacle, hermetic, round flange, jam nut mounting Product standardThe European Standard EN 3645-010:2006 has

2、 the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3645-010:2006This British Standard was published un

3、der the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978-0-580-49952-4National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3645-010:2006.The UK participation in its preparation was entrusted by Technical Committee

4、ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users

5、are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3645-010 December 2006 ICS 49.060 English Version Aerospace serie

6、s - Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 010: Receptacle, hermetic, round flange, jam nut mounting - Product standard Srie arospatiale - Connecteurs lectriques circulaires contacts protgs, accouplement p

7、ar filetage pas rapide trois filets, tempratures dutilisation 175 C ou 200 C continu - Partie 010 : Embase collerette ronde, hermtique fixation par crou - Norme de produit Luft- und Raumfahrt - Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung, Dauerbetriebstemper

8、aturen 175 C oder 200 C - Teil 010: Hermetischer Fester Steckverbinder mit runden Schwei und Mutternbefestigung - Produktnorm This European Standard was approved by CEN on 28 September 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

9、giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official v

10、ersions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu

11、m, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZA

12、TION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3645-010:2006: E2 Contents Page Foreword3 1 Scope 4 2 No

13、rmative references 4 3 Terms and definitions .4 4 Required characteristics.5 5 Designation 8 6 Marking .8 7 Technical specification .8 EN 3645-010:20063 Foreword This document (EN 3645-010:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-ST

14、AN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the stat

15、us of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject o

16、f patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,

17、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3645-010:20064 1 Scope This standard

18、specifies the characteristics of hermetic receptacles with jam nut mounting in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in Table 3. For plugs and protective covers, see EN 3645-006, EN 3645-008, EN 3645-011 and EN 3645-012 respectively.

19、 The contacts are unremovable and soldered termination. These connectors are derived from and interchangeable with model Y in specification MIL-DTL-38999/23. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t

20、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3645-001, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 001: T

21、echnical specification. EN 3645-002, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements. EN 3645-006, Aerospace series Connectors, electrical,

22、circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 006: Protective cover for receptacle Product standard. EN 3645-008, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C

23、or 200 C continuous Part 008: Non release plug with grounding ring Product standard. EN 3645-011, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 011: Lanyard release plug with grounding fingers Type

24、 1 Product standard. EN 3645-012, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 012: Lanyard release plug with grounding fingers Type 2 Product standard. MIL-DTL-38999/23, Connectors, electrical, c

25、ircular, threaded, receptacle, jam-nut mounting, hermetic, hermetic solder contacts, series III, metric.1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3645-001 apply. 1) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301

26、 USA. EN 3645-010:20065 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Red strip 3 H on flats 2 3 holes 1,5 min. for brake wire (see option according to Detail D) 4 B on flat 5 Seal NOTE One disengagement is permissibl

27、e to accept the accessory mounting. Figure 1 Hermetic jam nut receptacle Option D (Slot with close edges) (without seal) Seal EN 3645-010:20066 Table 1 Hermetic jam nut receptacle - Dimensions A B C aD E F bG H K max. Shell size 0,3 + 0,10 0,15 + 0,10 0,20 + 0,13 0,03 0,13 max. Thread Male contact F

28、emale contact09 30,2 16,53 17,40 15,9 M171 6g 0,1 R 24,00 21,82 11 34,9 19,07 20,60 18,8 M201 6g 0,1 R 27,00 24,99 5,3 5,9 13 38,1 23,82 25,40 23,8 M251 6g 0,1 R 32,00 29,77 15 41,3 26,97 28,50 26,8 M281 6g 0,1 R 36,00 32,91 17 44,5 30,15 31,85 2,39 1,14 30,8 M321 6g 0,1 R c37,00 36,12 19 49,2 33,32

29、 34,90 33,8 M351 6g 0,1 R 41,00 39,25 21 52,4 36,50 37,9036,8 M381 6g 0,1 R 46,00 42,47 23 55,6 39,67 41,20 39,8 M411 6g 0,1 R 50,00 45,61 25 58,7 42,85 44,40 3,58 1,91 42,8 M441 6g 0,1 R 51,23 49,25 5,1 5,7 L M N P S W X Y Z Mass g + 0,3 0 0,13 + 0,4 0,1 0,4 + 0,7 0,1 max. Stainless steel 9,10 16,3

30、 15,30 27,0 20,5020,19 34 9,10 19,4 16,40 14,1 31,8 29,2 25,2724,97 41 9,10 22,7 21,60 34,9 28,4528,14 50 9,10 25,9 24,80 38,1 31,6231,32 62 9,10 29,0 28,00 41,3 2,2 29,3 34,8034,49 1,85 1,70 83 9,70 32,2 31,20 46,0 37,9237,62 108 9,70 35,4 34,30 49,2 41,2040,69 141 9,70 38,6 37,50 52,4 44,3743,86 1

31、72 9,70 41,7 40,70 14,3 55,6 3,0 30,1 47,5547,04 2,69 2,54 203 aDimensions C and 1,5 mm shall be compatible with the panel hole bDiameter F corresponds to the start of the thread cUpper diameter modified as follow: 31,95 max. 31,80 min. EN 3645-010:20067 4.2 Materials and surface treatment See Table

32、 3. 4.3 Recommended panel cut-out See Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Figure 2 Panel cut-out Table 2 Panel cut-out - Dimensions A B C Shell size + 0,25 0 0 0,25 min. 09 17,70 16,99 31,80 11 20,88 19,53 35,00 13 25,58 24,26 39,40 15 28,80 27,53 42,50 17 31,98 30,68

33、 45,70 19 35,15 33,86 48,50 21 38,28 37,06 51,70 23 41,50 40,24 54,90 25 44,68 43,41 58,00 4.4 Electrical, mechanical and climatic characteristics See EN 3645-002. EN 3645-010:20068 5 Designation EXAMPLE Description block JAM NUT ELECTRICAL CONNECTOR Identity block EN3645-Y7GN35MA Number of the basi

34、c standard Model according to Table 3 Shell code for nut mounting receptacle Shell size code according to Table 4 Only N: no grounded cavity Contact arrangement according to EN 3645-002 except those containing coaxial or triaxial contacts or size 10 contacts Contact code M: male with solder cup X: m

35、ale with eyelet Polarization: N, A, B, C, D, E NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Model coding Model Description Y Hermetic receptacles, with shell in stainless steel Soldered contacts Maximum operating temperature 200 C co

36、ntinuous Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G23 H 25 J 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001. EN 3645-010:2006blankBS EN 3645-010:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is th

37、e independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure tha

38、t they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, t

39、he identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, inte

40、rnational and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to sup

41、ply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BS

42、I electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substan

43、tial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found a

44、t http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

45、 Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of neces

46、sary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.