EN 3475-302-2006 en Aerospace Series - Cables Electrical Aircraft use - Test Methods - Part 302 Voltage Proof Test《航空航天系列 飞机用电缆 测试方法 第302部分 电压保护试验》.pdf

《EN 3475-302-2006 en Aerospace Series - Cables Electrical Aircraft use - Test Methods - Part 302 Voltage Proof Test《航空航天系列 飞机用电缆 测试方法 第302部分 电压保护试验》.pdf》由会员分享，可在线阅读，更多相关《EN 3475-302-2006 en Aerospace Series - Cables Electrical Aircraft use - Test Methods - Part 302 Voltage Proof Test《航空航天系列 飞机用电缆 测试方法 第302部分 电压保护试验》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3475-302:2006Aerospace series Cable, electrical, aircraft use Test methods Part 302: Voltage proof testThe European Standard EN 3475-302:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g

2、50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3475-302:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49156 0National forewordThis

3、 British Standard was published by BSI. It is the UK implementation of EN 3475-302:2006. It supersedes BS EN 3475-302:2002 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee A

4、CE/6/-/2, Aerospace Cables.A list of organizations represented on ACE/6/-/2 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot

5、 confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3475-302May 2006ICS 49.060 Supersedes EN 3475-302:2002 English VersionAerospace series - Cable, electrical, aircraft use - Test methods- Part 302: Voltag

6、e proof testSrie arospatiale - Cbles lectriques usagearonautique - Mthodes dessais - Partie 302 : Tenue entensionLuft- und Raumfahrt - Elektrische Leitungen frLuftfahrtverwendung - Prfverfahren - Teil 302:SpannungsfestigkeitThis European Standard was approved by CEN on 13 January 2006.CEN members ar

7、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to th

8、e Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status

9、 as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slov

10、enia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN nati

11、onal Members.Ref. No. EN 3475-302:2006: EEN 3475-302:2006 (E) 2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Immersion test 4 4 Dry spark test (in production)4 5 Dry impulse test (test in production as an alternative to 4).5 6 Voltage test of components (screened cables) 6 EN 3475

12、-302:2006 (E) 3 Foreword This European Standard (EN 3475-302:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval

13、of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and confli

14、cting national standards shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This Europ

15、ean Standard supersedes EN 3475-302:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hu

16、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3475-302:2006 (E) 4 1 Scope This standard specifies a method of performing voltage proof tests on finished c

17、ables and cables in course of production. It shall be used together with EN 3475-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

18、the referenced document (including any amendments) applies. EN 3475-100, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. 3 Immersion test The specimens, each 15 m long, shall be immersed in the solution so that their ends are at least 150 mm from the surface of the

19、solution. The composition of the solution, at a temperature of between 15 C and 25 C, shall be as follows: sodium chloride 30 g distilled water 1 000 g wetting agent 2 g After immersion for 1 h, the voltage specified by the technical specification with a frequency of 40 Hz to 60 Hz, shall be applied

20、 between the conductor of the cable and the screen, if present, or an electrode in contact with the liquid for 5 min. Single and multicore (jacketed) without shield: between the conductor(s) and an electrode in contact with the liquid Shielded and jacketed cables between the shield and an electrode

21、in contact with the liquid The voltage rise time shall be between 300 V per second and 500 V per second. There shall be no perforation of the insulation or jacket. 4 Dry spark test (in production) All the finished cables shall pass, without flash-over, through the electrode of a suitable dry tester,

22、 at the voltage stated in the technical specification at a frequency of 40 Hz to 60 Hz. The electrode consists of an assembly of small chains or other metallic feelers suitable for making close contact with practically the whole surface of the cable. The length of the electrode and speed of the cabl

23、e shall be such that each portion of the insulation or jacket is subjected to the test voltage for at least 0,20 s. EN 3475-302:2006 (E) 5 The voltage shall be applied: Single and multicore (jacketed) without shield: between the conductor(s) and the electrode Shielded and jacketed cables between the

24、 shield and the electrode There shall be no perforation of the insulation or jacket. NOTE If a defect is found, a minimum length of 30 mm shall be cut away from each side of the defective point. 5 Dry impulse test (test in production as an alternative to 4) Apparatus The electrode through which the

25、cable passes when subjected to the voltage test shall be formed of beaded chains so that effectively the whole surface of the cable insulator is in contact with the beads. The characteristics and ancillary apparatus of the impulse test shall be as follows. Impulse test The form of the signal shall b

26、e negative pulse with a peak value of the cable test voltage followed by a damped oscillation. The peak voltage is stated in the technical specification. The rise time of the negative pulse of the signal between 0 % and 90 % of the peak voltage specified shall not be greater than 75 s. The peak valu

27、e of the first positive overshoot of the signal and each of the damped oscillations which flow from it shall be less than the initial negative pulse. The time during which each pulse and its damped oscillation (positive and negative) remain at a voltage equal to 80 % or higher than the specified pea

28、k voltage shall be between 20 s and 100 s. The pulse rate shall be between 200 pulses and 500 pulses per second inclusive. Apart from regulation of the peak voltage, conformity with the impulse test parameters shall be defined without capacitance load applied to the electrode. Capacity tolerance As

29、far as the capacitive load is concerned, the suitable tolerance for the apparatus shall be such that where there is an increase in the capacitive load between electrode and earth, the peak voltage shall not be reduced by more than 12 % from an initial load of 12,5 pF/25 mm to 25 pF/25 mm electrode l

30、ength. Voltmeter A voltmeter allowing continuous reading of the voltage at the electrode terminals is connected. The voltmeter shall be capable of showing a total deviation for a voltage not exceeding 15 kV and shall be accurate to within a minimum of 4 % of the test voltage. Error detection circuit

31、 The test apparatus shall consist of an error detection circuit with visual or audible indication of an insulation fault automatically cutting off the supply to the electrode and stopping the passage of the cable. The detection circuit shall be sensitive enough to show the fault at 75 % of the speci

32、fied test voltage when an arc occurs between the electrode and earth through a resistance of 20 k; it shall also be capable of detecting a fault with a duration corresponding to that of a pulse. EN 3475-302:2006 (E) 6 Calibration of apparatus The voltmeter shall be calibrated by comparison with anot

33、her voltmeter capable of detecting the peak voltage of the electrode with or without auxiliary circuit. During calibration, the calibrated voltmeter shall be directly connected to one of the electrodes or through a calibrated attenuator circuit. The pulse generator shall be switched on and the contr

34、ol voltage of the generator regulated until the voltage reading on the calibrated voltmeter corresponds to the specified voltage; at this moment the voltage reading on the voltmeter to be calibrated shall be noted. The calibration shall be repeated for each peak voltage at which it is intended to op

35、erate the equipment. A calibrated oscilloscope can also be used connected to the electrode through an attenuator. Thus the value of the negative pulse peak can be read directly on the wave form indicator. An oscilloscope connected to the electrode at appropriate different points can also be used to

36、check the conformity of the other waveform parameters specified for the impulse test. Method The finished cable shall be passed through the electrode and the conductor(s) earthed at one or both ends. The voltage shall be applied: Single and multicore (jacketed) without shield: between the conductor(

37、s) and the electrode Shielded and jacketed cables between the shield and the electrode The electrode shall be supplied with the specified voltage and after a final voltage adjustment the cable shall be passed from the pay-off reel to the take-up reel through the electrode. The line speed shall be su

38、ch that the cable is subjected to no fewer than three pulses and no more than 100 pulses at any given point. During the test, which includes the insertion of new lengths of cable, the cable shall be tested over its total length, including the ends, complying with the procedure. Any ends or other par

39、ts of the cable not tested in accordance with this method shall be withdrawn. There shall be no perforation of the insulation or jacket. NOTE If a defect is found, a minimum length of 50 mm shall be cut away from each side of the defective point. 6 Voltage test of components (screened cables) The ca

40、bles shall be subjected to a voltage test at ambient temperature. The r.m.s. value of the voltage shall be specified in the technical specification at a frequency between 40 Hz and 60 Hz. The voltage shall be applied for at least 1 min between one component and the other components and the screen co

41、nnected together. There shall be no perforation of the insulation. blankBS EN 3475-302:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the

42、 international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services

43、. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members

44、 an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89

45、96 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on stand

46、ardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information

47、Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:

48、 +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI pu

49、blications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing t